On Mon, Feb 18, 2013 at 03:06:10PM +0800, Mark Zhang wrote:
> On 02/18/2013 02:48 PM, Thierry Reding wrote:
> > On Mon, Feb 18, 2013 at 02:17:53PM +0800, Mark Zhang wrote:
> >> On 02/14/2013 12:05 AM, Thierry Reding wrote:
> >>> The sequence for replacing the scanout buffer is much shorter than a
> >>> full mode change operation so implementing this callback considerably
> >>> speeds up cases where only a new framebuffer is to be scanned out.
> >>>
> >>> Signed-off-by: Thierry Reding <thierry.reding@xxxxxxxxxxxxxxxxx>
> >>> ---
> >>> Changes in v3:
> >>> - split DC_CMD_STATE_CONTROL writes
> >>>
> >>> drivers/gpu/drm/tegra/dc.c | 31 +++++++++++++++++++++++++++++++
> >>> 1 file changed, 31 insertions(+)
> >>>
> >>> diff --git a/drivers/gpu/drm/tegra/dc.c b/drivers/gpu/drm/tegra/dc.c
> >>> index 8f97b1c..cc4c85e 100644
> >>> --- a/drivers/gpu/drm/tegra/dc.c
> >>> +++ b/drivers/gpu/drm/tegra/dc.c
> >>> @@ -114,6 +114,27 @@ static int tegra_dc_add_planes(struct drm_device *drm, struct tegra_dc *dc)
> >>> return 0;
> >>> }
> >>>
> >>> +static int tegra_dc_set_base(struct tegra_dc *dc, int x, int y,
> >>> + struct tegra_framebuffer *fb)
> >>> +{
> >>> + unsigned long value;
> >>> +
> >>> + tegra_dc_writel(dc, WINDOW_A_SELECT, DC_CMD_DISPLAY_WINDOW_HEADER);
> >>> +
> >>> + value = fb->base.offsets[0] + y * fb->base.pitches[0] +
> >>> + x * fb->base.bits_per_pixel / 8;
> >>> +
> >>> + tegra_dc_writel(dc, fb->obj->paddr + value, DC_WINBUF_START_ADDR);
> >>> +
> >>> + value = GENERAL_UPDATE | WIN_A_UPDATE;
> >>> + tegra_dc_writel(dc, value, DC_CMD_STATE_CONTROL);
> >>> +
> >>> + value = GENERAL_ACT_REQ | WIN_A_ACT_REQ;
> >>> + tegra_dc_writel(dc, value, DC_CMD_STATE_CONTROL);
> >>> +
> >>> + return 0;
> >>> +}
> >>
> >> Again, what do you think about the "line stride" problem I mentioned:
> >>
> >> http://lists.freedesktop.org/archives/dri-devel/2013-January/033561.html
> >>
> >> Don't get me wrong that I also don't want to add a line stride update
> >> here because that doesn't make sense. It's just a workaround. But we
> >> need to find a way to make multi-head page flip working.
> >
> > I'm not sure that it's something we need to support. .mode_set_base() is
> > explicitly used only for cases where the framebuffer configuration
> > doesn't change. That is, only in cases where the only thing that changes
> > is the physical address of the framebuffer to be displayed.
> >
> > The current case where one framebuffer is used as scanout for both
> > outputs isn't something that page-flipping can support. Page-flipping is
> > always per-CRTC because typically each CRTC would run at a different
> > frequency (or even if both ran at the same frequency the VBLANK is very
> > unlikely to coincide anyway).
> >
> > So an application that wants to support page-flipping on two outputs
> > also needs to take care to set them up with different framebuffers, in
> > which case what you're describing here can't really happen.
>
> Yes, the userspace application needs to setup different framebuffers for
> different crtcs. So if LVDS & HDMI are connected, here is what the
> application does:
>
> 1. drm reports that 2 connectors: LVDS & HDMI are present in the system
> 2. The resolution of them are: 1366x768 & 1080p
> 3. Userspace application allocates 2 fbs according to the resolution got
> above.
> 4. call drmModeSetCrtc to switch the fb shown in LVDS to the new fb we
> created.
> 5. At this time, remember the line stride setting in dc which connects
> with LVDS is calculated according to the 1080p resolution. So finally we
> got a corrupt display because we're showing a 1366x768 fb but with
> 1080p's line stride.
I don't see how the 1080p stride would still be relevant here. Setting
the LVDS to the new 1366x768 framebuffer should trigger a full modeset
and therefore set the stride to the value required by the new 1366x768
framebuffer.
Thierry
Attachment:
pgpRm4V4CPChi.pgp
Description: PGP signature
_______________________________________________ dri-devel mailing list dri-devel@xxxxxxxxxxxxxxxxxxxxx http://lists.freedesktop.org/mailman/listinfo/dri-devel
