V1:
1. The MCU FW controling ASPEED DP is loaded by BMC boot loader.
2. Driver starts after CR[3:1] == 111b that indicates Tx is ASTDP,
and CRD1[5] has been asserted by BMVC boot loader.
3. EDID is prioritized by DP monitor.
4. DP's EDID has high priority to decide resolution supporting.
V2:
Modules description:
1. ASTDP (ASPEED DisplayPort) is controlled by dedicated
AST-MCU (ASPEED propriatary MCU).
2. MCU is looping in charged of HPD, Read EDID, Link Training with
DP sink.
3. ASTDP and AST-MUC reside in BMC (Baseboard Management controller)
addressing-space.
4. ASPEED DRM driver requests MCU to get HPD and EDID by CR-scratched
register.
Booting sequence:
1. Check if TX is ASTDP // ast_dp_launch()
2. Check if DP-MCU FW has loaded // ast_dp_launch()
3. Read EDID // ast_dp_read_edid()
4. Resolution switch // ast_dp_SetOutput()
V3:
1. Remove unneeded semicolon.
2. Apply to git://anongit.freedesktop.org/drm/drm, instead of
git://anongit.freedesktop.org/drm/drm-misc
3. Resolve auto build test WARNINGs on V1 patch.
Signed-off-by: KuoHsiang Chou <kuohsiang_chou@xxxxxxxxxxxxxx>
Reported-by: kernel test robot <lkp@xxxxxxxxx>
---
drivers/gpu/drm/ast/Makefile | 2 +-
drivers/gpu/drm/ast/ast_dp.c | 292 +++++++++++++++++++++++++++++++++
drivers/gpu/drm/ast/ast_drv.h | 127 ++++++++++++++
drivers/gpu/drm/ast/ast_main.c | 5 +-
drivers/gpu/drm/ast/ast_mode.c | 46 +++++-
drivers/gpu/drm/ast/ast_post.c | 4 +-
6 files changed, 468 insertions(+), 8 deletions(-)
create mode 100644 drivers/gpu/drm/ast/ast_dp.c
diff --git a/drivers/gpu/drm/ast/Makefile b/drivers/gpu/drm/ast/Makefile
index 21f71160b..5a53ce51f 100644
--- a/drivers/gpu/drm/ast/Makefile
+++ b/drivers/gpu/drm/ast/Makefile
@@ -3,6 +3,6 @@
# Makefile for the drm device driver. This driver provides support for the
# Direct Rendering Infrastructure (DRI) in XFree86 4.1.0 and higher.
-ast-y := ast_drv.o ast_i2c.o ast_main.o ast_mm.o ast_mode.o ast_post.o ast_dp501.o
+ast-y := ast_drv.o ast_i2c.o ast_main.o ast_mm.o ast_mode.o ast_post.o ast_dp501.o ast_dp.o
obj-$(CONFIG_DRM_AST) := ast.o
diff --git a/drivers/gpu/drm/ast/ast_dp.c b/drivers/gpu/drm/ast/ast_dp.c
new file mode 100644
index 000000000..1daa25d92
--- /dev/null
+++ b/drivers/gpu/drm/ast/ast_dp.c
@@ -0,0 +1,292 @@
+// SPDX-License-Identifier: GPL-2.0
+// Copyright (c) 2021, ASPEED Technology Inc.
+// Authors: KuoHsiang Chou <kuohsiang_chou@xxxxxxxxxxxxxx>
+
+#include <linux/firmware.h>
+#include <linux/delay.h>
+#include <drm/drm_print.h>
+#include "ast_drv.h"
+
+bool ast_dp_read_edid(struct drm_device *dev, u8 *ediddata)
+{
+ struct ast_private *ast = to_ast_private(dev);
+ u8 i = 0, j = 0;
+
+#ifdef DPControlPower
+ u8 bDPState_Change = false;
+
+ // Check DP power off or not.
+ if (ast->ASTDP_State & AST_DP_PHY_SLEEP) {
+ // DP power on
+ ast_dp_PowerOnOff(dev, AST_DP_POWER_ON);
+ bDPState_Change = true;
+ }
+#endif
+
+ /*
+ * CRD1[b5]: DP MCU FW is executing
+ * CRDC[b0]: DP link success
+ * CRDF[b0]: DP HPD
+ * CRE5[b0]: Host reading EDID process is done
+ */
+ if (!(ast_get_index_reg_mask(ast, AST_IO_CRTC_PORT, 0xD1, ASTDP_MCU_FW_EXECUTING) &&
+ ast_get_index_reg_mask(ast, AST_IO_CRTC_PORT, 0xDC, ASTDP_LINK_SUCCESS) &&
+ ast_get_index_reg_mask(ast, AST_IO_CRTC_PORT, 0xDF, ASTDP_HPD) &&
+ ast_get_index_reg_mask(ast, AST_IO_CRTC_PORT, 0xE5,
+ ASTDP_HOST_EDID_READ_DONE_MASK))) {
+#ifdef DPControlPower
+ // Set back power off
+ if (bDPState_Change)
+ ast_dp_PowerOnOff(dev, AST_DP_POWER_OFF);
+#endif
+ return false;
+ }
+
+ ast_set_index_reg_mask(ast, AST_IO_CRTC_PORT, 0xE5, (u8) ~ASTDP_HOST_EDID_READ_DONE_MASK,
+ 0x00);
+
+ for (i = 0; i < 32; i++) {
+ /*
+ * CRE4[7:0]: Read-Pointer for EDID (Unit: 4bytes); valid range: 0~64
+ */
+ ast_set_index_reg_mask(ast, AST_IO_CRTC_PORT, 0xE4,
+ (u8) ~ASTDP_EDID_READ_POINTER_MASK, (u8) i);
+ j = 0;
+
+ /*
+ * CRD7[b0]: valid flag for EDID
+ * CRD6[b0]: mirror read pointer for EDID
+ */
+ while ((ast_get_index_reg_mask(ast, AST_IO_CRTC_PORT, 0xD7,
+ ASTDP_EDID_VALID_FLAG_MASK) != 0x01) ||
+ (ast_get_index_reg_mask(ast, AST_IO_CRTC_PORT, 0xD6,
+ ASTDP_EDID_READ_POINTER_MASK) != i)) {
+ mdelay(j+1);
+
+ if (!(ast_get_index_reg_mask(ast, AST_IO_CRTC_PORT, 0xD1,
+ ASTDP_MCU_FW_EXECUTING) &&
+ ast_get_index_reg_mask(ast, AST_IO_CRTC_PORT, 0xDC,
+ ASTDP_LINK_SUCCESS) &&
+ ast_get_index_reg_mask(ast, AST_IO_CRTC_PORT, 0xDF, ASTDP_HPD))) {
+ ast_set_index_reg_mask(ast, AST_IO_CRTC_PORT, 0xE5,
+ (u8) ~ASTDP_HOST_EDID_READ_DONE_MASK,
+ ASTDP_HOST_EDID_READ_DONE);
+ return false;
+ }
+
+ j++;
+ if (j > 200) {
+ ast_set_index_reg_mask(ast, AST_IO_CRTC_PORT, 0xE5,
+ (u8) ~ASTDP_HOST_EDID_READ_DONE_MASK,
+ ASTDP_HOST_EDID_READ_DONE);
+ return false;
+ }
+ }
+
+ *(ediddata) = ast_get_index_reg_mask(ast, AST_IO_CRTC_PORT,
+ 0xD8, ASTDP_EDID_READ_DATA_MASK);
+ *(ediddata + 1) = ast_get_index_reg_mask(ast, AST_IO_CRTC_PORT, 0xD9,
+ ASTDP_EDID_READ_DATA_MASK);
+ *(ediddata + 2) = ast_get_index_reg_mask(ast, AST_IO_CRTC_PORT, 0xDA,
+ ASTDP_EDID_READ_DATA_MASK);
+ *(ediddata + 3) = ast_get_index_reg_mask(ast, AST_IO_CRTC_PORT, 0xDB,
+ ASTDP_EDID_READ_DATA_MASK);
+
+ if (i == 31) {
+ /*
+ * For 128-bytes EDID_1.3,
+ * 1. Add the value of Bytes-126 to Bytes-127.
+ * The Bytes-127 is Checksum. Sum of all 128bytes should
+ * equal 0 (mod 256).
+ * 2. Modify Bytes-126 to be 0.
+ * The Bytes-126 indicates the Number of extensions to
+ * follow. 0 represents noextensions.
+ */
+ *(ediddata + 3) = *(ediddata + 3) + *(ediddata + 2);
+ *(ediddata + 2) = 0;
+ }
+
+ ediddata += 4;
+ }
+
+ ast_set_index_reg_mask(ast, AST_IO_CRTC_PORT, 0xE5, (u8) ~ASTDP_HOST_EDID_READ_DONE_MASK,
+ ASTDP_HOST_EDID_READ_DONE);
+
+#ifdef DPControlPower
+ // Set back power off
+ if (bDPState_Change)
+ ast_dp_PowerOnOff(dev, AST_DP_POWER_OFF);
+#endif
+
+ return true;
+}
+
+/*
+ * Launch Aspeed DP
+ */
+bool ast_dp_launch(struct drm_device *dev, u8 bPower)
+{
+ u32 i = 0, j = 0, WaitCount = 1;
+ u8 bDPTX = 0;
+ u8 bDPExecute = 1;
+
+ struct ast_private *ast = to_ast_private(dev);
+ // S3 come back, need more time to wait BMC ready.
+ if (bPower)
+ WaitCount = 300;
+
+ // Fill
+ ast->tx_chip_type = AST_TX_NONE;
+
+ // Wait total count by different condition.
+ // This is a temp solution for DP check
+ for (j = 0; j < WaitCount; j++) {
+ bDPTX = ast_get_index_reg_mask(ast, AST_IO_CRTC_PORT, 0xD1, TX_TYPE_MASK);
+
+ if (bDPTX)
+ break;
+
+ msleep(100);
+ }
+
+ // 0xE : ASTDP with DPMCU FW handling
+ if (bDPTX == ASTDP_DPMCU_TX) {
+ // Wait one second then timeout.
+ i = 0;
+
+ while (ast_get_index_reg_mask(ast, AST_IO_CRTC_PORT, 0xD1, COPROCESSOR_LAUNCH) !=
+ COPROCESSOR_LAUNCH) {
+ i++;
+ // wait 100 ms
+ msleep(100);
+
+ if (i >= 10) {
+ // DP would not be ready.
+ bDPExecute = 0;
+ break;
+ }
+ }
+
+ if (bDPExecute)
+ ast->tx_chip_type = AST_TX_ASTDP;
+ }
+
+ return true;
+}
+
+#ifdef DPControlPower
+
+void ast_dp_PowerOnOff(struct drm_device *dev, u8 Mode)
+{
+ struct ast_private *ast = to_ast_private(dev);
+ // Read and Turn off DP PHY sleep
+ u8 bE3 = ast_get_index_reg_mask(ast, AST_IO_CRTC_PORT, 0xE3, AST_DP_VIDEO_ENABLE);
+
+ // Turn on DP PHY sleep
+ if (!Mode)
+ bE3 |= AST_DP_PHY_SLEEP;
+
+ // DP Power on/off
+ ast_set_index_reg_mask(ast, AST_IO_CRTC_PORT, 0xE3, (u8) ~AST_DP_PHY_SLEEP, bE3);
+
+ // Save ASTDP power state
+ ast->ASTDP_State = bE3;
+}
+
+#endif
+
+void ast_dp_SetOnOff(struct drm_device *dev, u8 Mode)
+{
+ struct ast_private *ast = to_ast_private(dev);
+
+ // Video On/Off
+ ast_set_index_reg_mask(ast, AST_IO_CRTC_PORT, 0xE3, (u8) ~AST_DP_VIDEO_ENABLE, Mode);
+
+ // Save ASTDP power state
+ ast->ASTDP_State = Mode;
+
+ // If DP plug in and link successful then check video on / off status
+ if (ast_get_index_reg_mask(ast, AST_IO_CRTC_PORT, 0xDC, ASTDP_LINK_SUCCESS) &&
+ ast_get_index_reg_mask(ast, AST_IO_CRTC_PORT, 0xDF, ASTDP_HPD)) {
+ Mode <<= 4;
+ while (ast_get_index_reg_mask(ast, AST_IO_CRTC_PORT, 0xDF,
+ ASTDP_MIRROR_VIDEO_ENABLE) != Mode) {
+ // wait 1 ms
+ mdelay(1);
+ }
+ }
+}
+
+void ast_dp_SetOutput(struct drm_crtc *crtc, struct ast_vbios_mode_info *vbios_mode)
+{
+ struct ast_private *ast = to_ast_private(crtc->dev);
+
+ u32 ulRefreshRateIndex;
+ u8 ModeIdx;
+
+ ulRefreshRateIndex = vbios_mode->enh_table->refresh_rate_index - 1;
+
+ switch (crtc->mode.crtc_hdisplay) {
+ case 320:
+ ModeIdx = ASTDP_320x240_60;
+ break;
+ case 400:
+ ModeIdx = ASTDP_400x300_60;
+ break;
+ case 512:
+ ModeIdx = ASTDP_512x384_60;
+ break;
+ case 640:
+ ModeIdx = (ASTDP_640x480_60 + (u8) ulRefreshRateIndex);
+ break;
+ case 800:
+ ModeIdx = (ASTDP_800x600_56 + (u8) ulRefreshRateIndex);
+ break;
+ case 1024:
+ ModeIdx = (ASTDP_1024x768_60 + (u8) ulRefreshRateIndex);
+ break;
+ case 1152:
+ ModeIdx = ASTDP_1152x864_75;
+ break;
+ case 1280:
+ if (crtc->mode.crtc_vdisplay == 800)
+ ModeIdx = (ASTDP_1280x800_60_RB - (u8) ulRefreshRateIndex);
+ else // 1024
+ ModeIdx = (ASTDP_1280x1024_60 + (u8) ulRefreshRateIndex);
+ break;
+ case 1360:
+ case 1366:
+ ModeIdx = ASTDP_1366x768_60;
+ break;
+ case 1440:
+ ModeIdx = (ASTDP_1440x900_60_RB - (u8) ulRefreshRateIndex);
+ break;
+ case 1600:
+ if (crtc->mode.crtc_vdisplay == 900)
+ ModeIdx = (ASTDP_1600x900_60_RB - (u8) ulRefreshRateIndex);
+ else //1200
+ ModeIdx = ASTDP_1600x1200_60;
+ break;
+ case 1680:
+ ModeIdx = (ASTDP_1680x1050_60_RB - (u8) ulRefreshRateIndex);
+ break;
+ case 1920:
+ if (crtc->mode.crtc_vdisplay == 1080)
+ ModeIdx = ASTDP_1920x1080_60;
+ else //1200
+ ModeIdx = ASTDP_1920x1200_60;
+ break;
+ default:
+ return;
+ }
+
+ /*
+ * CRE0[7:0]: MISC0 ((0x00: 18-bpp) or (0x20: 24-bpp)
+ * CRE1[7:0]: MISC1 (default: 0x00)
+ * CRE2[7:0]: video format index (0x00 ~ 0x20 or 0x40 ~ 0x50)
+ */
+ ast_set_index_reg_mask(ast, AST_IO_CRTC_PORT, 0xE0, (u8) ~ASTDP_CLEAR_MASK,
+ ASTDP_MISC0_24bpp);
+ ast_set_index_reg_mask(ast, AST_IO_CRTC_PORT, 0xE1, (u8) ~ASTDP_CLEAR_MASK, ASTDP_MISC1);
+ ast_set_index_reg_mask(ast, AST_IO_CRTC_PORT, 0xE2, (u8) ~ASTDP_CLEAR_MASK, ModeIdx);
+}
diff --git a/drivers/gpu/drm/ast/ast_drv.h b/drivers/gpu/drm/ast/ast_drv.h
index 00bfa41ff..799828503 100644
--- a/drivers/gpu/drm/ast/ast_drv.h
+++ b/drivers/gpu/drm/ast/ast_drv.h
@@ -71,6 +71,7 @@ enum ast_tx_chip {
AST_TX_SIL164,
AST_TX_ITE66121,
AST_TX_DP501,
+ AST_TX_ASTDP,
};
#define AST_DRAM_512Mx16 0
@@ -175,6 +176,9 @@ struct ast_private {
u8 dp501_maxclk;
u8 *dp501_fw_addr;
const struct firmware *dp501_fw; /* dp501 fw */
+
+ // ASTDP
+ u8 ASTDP_State;
};
static inline struct ast_private *to_ast_private(struct drm_device *dev)
@@ -336,10 +340,123 @@ int ast_mode_config_init(struct ast_private *ast);
#define AST_DP501_EDID_DATA 0xf020
/* Define for Soc scratched reg */
+#define COPROCESSOR_LAUNCH BIT(5)
+
+#define TX_TYPE_MASK GENMASK(3, 1)
+#define NO_TX (0 << 1)
+#define ITE66121_VBIOS_TX (1 << 1)
+#define SI164_VBIOS_TX (2 << 1)
+#define CH7003_VBIOS_TX (3 << 1)
+#define DP501_VBIOS_TX (4 << 1)
+#define ANX9807_VBIOS_TX (5 << 1)
+#define TX_FW_EMBEDDED_FW_TX (6 << 1)
+#define ASTDP_DPMCU_TX (7 << 1)
+
#define AST_VRAM_INIT_STATUS_MASK GENMASK(7, 6)
//#define AST_VRAM_INIT_BY_BMC BIT(7)
//#define AST_VRAM_INIT_READY BIT(6)
+/* Define for Soc scratched reg used on ASTDP */
+#define AST_DP_PHY_SLEEP BIT(4)
+#define AST_DP_VIDEO_ENABLE BIT(0)
+
+#define AST_DP_POWER_ON true
+#define AST_DP_POWER_OFF false
+
+/*
+ * CRD1[b5]: DP MCU FW is executing
+ * CRDC[b0]: DP link success
+ * CRDF[b0]: DP HPD
+ * CRE5[b0]: Host reading EDID process is done
+ */
+#define ASTDP_MCU_FW_EXECUTING BIT(5)
+#define ASTDP_LINK_SUCCESS BIT(0)
+#define ASTDP_HPD BIT(0)
+#define ASTDP_HOST_EDID_READ_DONE BIT(0)
+#define ASTDP_HOST_EDID_READ_DONE_MASK GENMASK(0, 0)
+
+/*
+ * CRB8[b1]: Enable VSYNC off
+ * CRB8[b0]: Enable HSYNC off
+ */
+#define AST_DPMS_VSYNC_OFF BIT(1)
+#define AST_DPMS_HSYNC_OFF BIT(0)
+
+/*
+ * CRDF[b4]: Mirror of AST_DP_VIDEO_ENABLE
+ * Precondition: A. ~AST_DP_PHY_SLEEP &&
+ * B. DP_HPD &&
+ * C. DP_LINK_SUCCESS
+ */
+#define ASTDP_MIRROR_VIDEO_ENABLE BIT(4)
+
+#define ASTDP_EDID_READ_POINTER_MASK GENMASK(7, 0)
+#define ASTDP_EDID_VALID_FLAG_MASK GENMASK(0, 0)
+#define ASTDP_EDID_READ_DATA_MASK GENMASK(7, 0)
+
+/*
+ * Display Transmittor Type:
+ */
+#define TX_TYPE_MASK GENMASK(3, 1)
+#define NO_TX (0 << 1)
+#define ITE66121_VBIOS_TX (1 << 1)
+#define SI164_VBIOS_TX (2 << 1)
+#define CH7003_VBIOS_TX (3 << 1)
+#define DP501_VBIOS_TX (4 << 1)
+#define ANX9807_VBIOS_TX (5 << 1)
+#define TX_FW_EMBEDDED_FW_TX (6 << 1)
+#define ASTDP_DPMCU_TX (7 << 1)
+
+/*
+ * ASTDP setmode registers:
+ * CRE0[7:0]: MISC0 ((0x00: 18-bpp) or (0x20: 24-bpp)
+ * CRE1[7:0]: MISC1 (default: 0x00)
+ * CRE2[7:0]: video format index (0x00 ~ 0x20 or 0x40 ~ 0x50)
+ */
+#define ASTDP_MISC0_24bpp BIT(5)
+#define ASTDP_MISC1 0
+#define ASTDP_CLEAR_MASK GENMASK(7, 0)
+
+/*
+ * ASTDP resoultion table:
+ * EX: ASTDP_A_B_C:
+ * A: Resolution
+ * B: Refresh Rate
+ * C: Misc information, such as CVT, Reduce Blanked
+ */
+#define ASTDP_640x480_60 0x00
+#define ASTDP_640x480_72 0x01
+#define ASTDP_640x480_75 0x02
+#define ASTDP_640x480_85 0x03
+#define ASTDP_800x600_56 0x04
+#define ASTDP_800x600_60 0x05
+#define ASTDP_800x600_72 0x06
+#define ASTDP_800x600_75 0x07
+#define ASTDP_800x600_85 0x08
+#define ASTDP_1024x768_60 0x09
+#define ASTDP_1024x768_70 0x0A
+#define ASTDP_1024x768_75 0x0B
+#define ASTDP_1024x768_85 0x0C
+#define ASTDP_1280x1024_60 0x0D
+#define ASTDP_1280x1024_75 0x0E
+#define ASTDP_1280x1024_85 0x0F
+#define ASTDP_1600x1200_60 0x10
+#define ASTDP_320x240_60 0x11
+#define ASTDP_400x300_60 0x12
+#define ASTDP_512x384_60 0x13
+#define ASTDP_1920x1200_60 0x14
+#define ASTDP_1920x1080_60 0x15
+#define ASTDP_1280x800_60 0x16
+#define ASTDP_1280x800_60_RB 0x17
+#define ASTDP_1440x900_60 0x18
+#define ASTDP_1440x900_60_RB 0x19
+#define ASTDP_1680x1050_60 0x1A
+#define ASTDP_1680x1050_60_RB 0x1B
+#define ASTDP_1600x900_60 0x1C
+#define ASTDP_1600x900_60_RB 0x1D
+#define ASTDP_1366x768_60 0x1E
+#define ASTDP_1152x864_75 0x1F
+
int ast_mm_init(struct ast_private *ast);
/* ast post */
@@ -360,4 +477,14 @@ void ast_init_3rdtx(struct drm_device *dev);
/* ast_i2c.c */
struct ast_i2c_chan *ast_i2c_create(struct drm_device *dev);
+/* aspeed DP */
+#define DPControlPower
+bool ast_dp_read_edid(struct drm_device *dev, u8 *ediddata);
+bool ast_dp_launch(struct drm_device *dev, u8 bPower);
+#ifdef DPControlPower
+void ast_dp_PowerOnOff(struct drm_device *dev, u8 Mode);
+#endif
+void ast_dp_SetOnOff(struct drm_device *dev, u8 Mode);
+void ast_dp_SetOutput(struct drm_crtc *crtc, struct ast_vbios_mode_info *vbios_mode);
+
#endif
diff --git a/drivers/gpu/drm/ast/ast_main.c b/drivers/gpu/drm/ast/ast_main.c
index 79a361867..9f25fa2c8 100644
--- a/drivers/gpu/drm/ast/ast_main.c
+++ b/drivers/gpu/drm/ast/ast_main.c
@@ -230,7 +230,7 @@ static int ast_detect_chip(struct drm_device *dev, bool *need_post)
ast->tx_chip_type = AST_TX_SIL164;
}
- if ((ast->chip == AST2300) || (ast->chip == AST2400)) {
+ if ((ast->chip == AST2300) || (ast->chip == AST2400) || (ast->chip == AST2500)) {
/*
* On AST2300 and 2400, look the configuration set by the SoC in
* the SOC scratch register #1 bits 11:8 (interestingly marked
@@ -254,7 +254,8 @@ static int ast_detect_chip(struct drm_device *dev, bool *need_post)
case 0x0c:
ast->tx_chip_type = AST_TX_DP501;
}
- }
+ } else if (ast->chip == AST2600)
+ ast_dp_launch(&ast->base, 0);
/* Print stuff for diagnostic purposes */
switch(ast->tx_chip_type) {
diff --git a/drivers/gpu/drm/ast/ast_mode.c b/drivers/gpu/drm/ast/ast_mode.c
index 44c2aafcb..1c7a57a03 100644
--- a/drivers/gpu/drm/ast/ast_mode.c
+++ b/drivers/gpu/drm/ast/ast_mode.c
@@ -984,21 +984,45 @@ static int ast_cursor_plane_init(struct ast_private *ast)
static void ast_crtc_dpms(struct drm_crtc *crtc, int mode)
{
struct ast_private *ast = to_ast_private(crtc->dev);
+ u8 ch = AST_DPMS_VSYNC_OFF | AST_DPMS_HSYNC_OFF;
/* TODO: Maybe control display signal generation with
* Sync Enable (bit CR17.7).
*/
switch (mode) {
case DRM_MODE_DPMS_ON:
- case DRM_MODE_DPMS_STANDBY:
- case DRM_MODE_DPMS_SUSPEND:
+ ast_set_index_reg_mask(ast, AST_IO_SEQ_PORT, 0x01, 0xdf, 0);
+ ast_set_index_reg_mask(ast, AST_IO_CRTC_PORT, 0xb6, 0xfc, 0);
if (ast->tx_chip_type == AST_TX_DP501)
ast_set_dp501_video_output(crtc->dev, 1);
+
+ if (ast->tx_chip_type == AST_TX_ASTDP) {
+#ifdef DPControlPower
+ ast_dp_PowerOnOff(crtc->dev, AST_DP_POWER_ON);
+#endif
+ ast_wait_for_vretrace(ast);
+ ast_dp_SetOnOff(crtc->dev, 1);
+ }
+
+ ast_crtc_load_lut(ast, crtc);
break;
+ case DRM_MODE_DPMS_STANDBY:
+ case DRM_MODE_DPMS_SUSPEND:
case DRM_MODE_DPMS_OFF:
+ ch = mode;
if (ast->tx_chip_type == AST_TX_DP501)
ast_set_dp501_video_output(crtc->dev, 0);
break;
+
+ if (ast->tx_chip_type == AST_TX_ASTDP) {
+ ast_dp_SetOnOff(crtc->dev, 0);
+#ifdef DPControlPower
+ ast_dp_PowerOnOff(crtc->dev, AST_DP_POWER_OFF);
+#endif
+ }
+
+ ast_set_index_reg_mask(ast, AST_IO_SEQ_PORT, 0x01, 0xdf, 0x20);
+ ast_set_index_reg_mask(ast, AST_IO_CRTC_PORT, 0xb6, 0xfc, ch);
}
}
@@ -1041,6 +1065,7 @@ ast_crtc_helper_atomic_flush(struct drm_crtc *crtc,
struct ast_private *ast = to_ast_private(crtc->dev);
struct ast_crtc_state *ast_crtc_state = to_ast_crtc_state(crtc_state);
struct ast_crtc_state *old_ast_crtc_state = to_ast_crtc_state(old_crtc_state);
+ struct ast_vbios_mode_info *vbios_mode_info = &ast_crtc_state->vbios_mode_info;
/*
* The gamma LUT has to be reloaded after changing the primary
@@ -1048,6 +1073,10 @@ ast_crtc_helper_atomic_flush(struct drm_crtc *crtc,
*/
if (old_ast_crtc_state->format != ast_crtc_state->format)
ast_crtc_load_lut(ast, crtc);
+
+ //Set Aspeed Display-Port
+ if (ast->tx_chip_type == AST_TX_ASTDP)
+ ast_dp_SetOutput(crtc, vbios_mode_info);
}
static void
@@ -1222,6 +1251,14 @@ static int ast_get_modes(struct drm_connector *connector)
ast->dp501_maxclk = ast_get_dp501_max_clk(connector->dev);
else
kfree(edid);
+ } else if (ast->tx_chip_type == AST_TX_ASTDP) {
+ edid = kmalloc(128, GFP_KERNEL);
+ if (!edid)
+ return -ENOMEM;
+
+ flags = ast_dp_read_edid(connector->dev, (u8 *)edid);
+ if (!flags)
+ kfree(edid);
}
if (!flags && ast_connector->i2c)
edid = drm_get_edid(connector, &ast_connector->i2c->adapter);
@@ -1256,7 +1293,7 @@ static enum drm_mode_status ast_mode_valid(struct drm_connector *connector,
if ((ast->chip == AST2100) || (ast->chip == AST2200) ||
(ast->chip == AST2300) || (ast->chip == AST2400) ||
- (ast->chip == AST2500)) {
+ (ast->chip == AST2500) || (ast->chip == AST2600)) {
if ((mode->hdisplay == 1920) && (mode->vdisplay == 1080))
return MODE_OK;
@@ -1378,7 +1415,8 @@ int ast_mode_config_init(struct ast_private *ast)
ast->chip == AST2200 ||
ast->chip == AST2300 ||
ast->chip == AST2400 ||
- ast->chip == AST2500) {
+ ast->chip == AST2500 ||
+ ast->chip == AST2600) {
dev->mode_config.max_width = 1920;
dev->mode_config.max_height = 2048;
} else {
diff --git a/drivers/gpu/drm/ast/ast_post.c b/drivers/gpu/drm/ast/ast_post.c
index b5d92f652..0aa9cf0fb 100644
--- a/drivers/gpu/drm/ast/ast_post.c
+++ b/drivers/gpu/drm/ast/ast_post.c
@@ -379,7 +379,9 @@ void ast_post_gpu(struct drm_device *dev)
ast_enable_mmio(dev);
ast_set_def_ext_reg(dev);
- if (ast->config_mode == ast_use_p2a) {
+ if (ast->chip == AST2600) {
+ ast_dp_launch(dev, 1);
+ } else if (ast->config_mode == ast_use_p2a) {
if (ast->chip == AST2500)
ast_post_chip_2500(dev);
else if (ast->chip == AST2300 || ast->chip == AST2400)
base-commit: cb6846fbb83b574c85c2a80211b402a6347b60b1
--
2.27.0
