From: Sankeerth Billakanti <sbillaka@xxxxxxxxxxxxxx>
Add edp controller and phy DT nodes for sc7280.
Signed-off-by: Sankeerth Billakanti <sbillaka@xxxxxxxxxxxxxx>
---
arch/arm64/boot/dts/qcom/sc7280.dtsi | 127 ++++++++++++++++++++++++++++++++++-
1 file changed, 126 insertions(+), 1 deletion(-)
diff --git a/arch/arm64/boot/dts/qcom/sc7280.dtsi b/arch/arm64/boot/dts/qcom/sc7280.dtsi
index aadf55d..5be318e 100644
--- a/arch/arm64/boot/dts/qcom/sc7280.dtsi
+++ b/arch/arm64/boot/dts/qcom/sc7280.dtsi
@@ -1412,7 +1412,7 @@
reg = <0 0xaf00000 0 0x20000>;
clocks = <&rpmhcc RPMH_CXO_CLK>,
<&gcc GCC_DISP_GPLL0_CLK_SRC>,
- <0>, <0>, <0>, <0>, <0>, <0>;
+ <0>, <0>, <0>, <0>, <&edp_phy 0>, <&edp_phy 1>;
clock-names = "bi_tcxo", "gcc_disp_gpll0_clk",
"dsi0_phy_pll_out_byteclk",
"dsi0_phy_pll_out_dsiclk",
@@ -1493,6 +1493,12 @@
remote-endpoint = <&dsi0_in>;
};
};
+ port@1 {
+ reg = <1>;
+ dpu_intf5_out: endpoint {
+ remote-endpoint = <&edp_in>;
+ };
+ };
};
mdp_opp_table: mdp-opp-table {
@@ -1608,6 +1614,101 @@
status = "disabled";
};
+
+ msm_edp: edp@aea0000 {
+ status = "disabled";
+ compatible = "qcom,sc7280-edp";
+ reg = <0 0xaea0000 0 0x200>,
+ <0 0xaea0200 0 0x200>,
+ <0 0xaea0400 0 0xc00>,
+ <0 0xaea1000 0 0x400>;
+
+ interrupt-parent = <&mdss>;
+ interrupts = <14 IRQ_TYPE_NONE>;
+
+ clocks = <&rpmhcc RPMH_CXO_CLK>,
+ <&gcc GCC_EDP_CLKREF_EN>,
+ <&dispcc DISP_CC_MDSS_AHB_CLK>,
+ <&dispcc DISP_CC_MDSS_EDP_AUX_CLK>,
+ <&dispcc DISP_CC_MDSS_EDP_LINK_CLK>,
+ <&dispcc DISP_CC_MDSS_EDP_LINK_INTF_CLK>,
+ <&dispcc DISP_CC_MDSS_EDP_PIXEL_CLK>;
+ clock-names = "core_xo", "core_ref",
+ "core_iface", "core_aux", "ctrl_link",
+ "ctrl_link_iface", "stream_pixel";
+ #clock-cells = <1>;
+ assigned-clocks = <&dispcc DISP_CC_MDSS_EDP_LINK_CLK_SRC>,
+ <&dispcc DISP_CC_MDSS_EDP_PIXEL_CLK_SRC>;
+ assigned-clock-parents = <&edp_phy 0>, <&edp_phy 1>;
+
+ phys = <&edp_phy>;
+ phy-names = "dp";
+
+ vdda-1p2-supply = <&vreg_l6b_1p2>;
+ vdda-0p9-supply = <&vreg_l10c_0p8>;
+ operating-points-v2 = <&edp_opp_table>;
+ power-domains = <&rpmhpd SC7280_CX>;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&edp_hot_plug_det>, <&edp_panel_power_on>;
+
+ panel-bklt-gpio = <&pm8350c_gpios 7 GPIO_ACTIVE_HIGH>;
+ panel-pwm-gpio = <&pm8350c_gpios 8 GPIO_ACTIVE_HIGH>;
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ port@0 {
+ reg = <0>;
+ edp_in: endpoint {
+ remote-endpoint = <&dpu_intf5_out>;
+ };
+ };
+ };
+
+ edp_opp_table: edp-opp-table {
+ compatible = "operating-points-v2";
+
+ opp-160000000 {
+ opp-hz = /bits/ 64 <160000000>;
+ required-opps = <&rpmhpd_opp_low_svs>;
+ };
+
+ opp-270000000 {
+ opp-hz = /bits/ 64 <270000000>;
+ required-opps = <&rpmhpd_opp_svs>;
+ };
+
+ opp-540000000 {
+ opp-hz = /bits/ 64 <540000000>;
+ required-opps = <&rpmhpd_opp_nom>;
+ };
+
+ opp-810000000 {
+ opp-hz = /bits/ 64 <810000000>;
+ required-opps = <&rpmhpd_opp_nom>;
+ };
+ };
+ };
+
+ edp_phy: phy@aec2000 {
+ status = "disabled";
+ compatible = "qcom,sc7280-edp-phy";
+ reg = <0 0xaec2a00 0 0x19c>,
+ <0 0xaec2200 0 0xa0>,
+ <0 0xaec2600 0 0xa0>,
+ <0 0xaec2000 0 0x1c0>;
+
+ clocks = <&rpmhcc RPMH_CXO_CLK>,
+ <&gcc GCC_EDP_CLKREF_EN>;
+ clock-names = "aux", "cfg_ahb";
+
+ vdda-pll-supply = <&vreg_l6b_1p2>;
+ vdda-phy-supply = <&vreg_l10c_0p8>;
+
+ #clock-cells = <1>;
+ #phy-cells = <0>;
+ };
};
pdc: interrupt-controller@b220000 {
@@ -1704,6 +1805,30 @@
function = "qup13";
};
+ edp_hot_plug_det: edp-hot-plug-det {
+ pinmux {
+ pins = "gpio60";
+ function = "edp_hot";
+ };
+ pinconf {
+ pins = "gpio60";
+ bias-pull-down;
+ input-enable;
+ };
+ };
+
+ edp_panel_power_on: edp-panel-power-on {
+ pinmux {
+ pins = "gpio80";
+ function = "gpio";
+ };
+ pinconf {
+ pins = "gpio80";
+ bias-disable;
+ output-high;
+ };
+ };
+
sdc1_on: sdc1-on {
clk {
pins = "sdc1_clk";
--
2.7.4
