On 2012-11-26 18:10, Steffen Trumtrar wrote: > Hi, > > On Mon, Nov 26, 2012 at 04:38:36PM +0200, Tomi Valkeinen wrote: >>> +optional properties: >>> + - hsync-active: hsync pulse is active low/high/ignored >>> + - vsync-active: vsync pulse is active low/high/ignored >>> + - de-active: data-enable pulse is active low/high/ignored >>> + - pixelclk-inverted: pixelclock is inverted (active on falling edge)/ >>> + non-inverted (active on rising edge)/ >>> + ignored (ignore property) >> >> I think hsync-active and vsync-active are clear, and commonly used, and >> they are used for both drm and fb mode conversions in later patches. >> >> de-active is not used in drm and fb mode conversions, but I think it's >> also clear. >> >> pixelclk-inverted is not used in the mode conversions. It's also a bit >> unclear to me. What does it mean that pix clock is "active on rising >> edge"? The pixel data is driven on rising edge? How about the sync >> signals and DE, when are they driven? Does your HW have any settings >> related to those? >> > > Those are properties commonly found in display specs. That is why they are here. > If the GPU does not support the property it can be omitted. So what does the pixelclk-inverted mean? Normally the SoC drives pixel data on rising edge, and the panel samples it at falling edge? And vice-versa for inverted? Or the other way around? When is hsync/vsync set? On rising or falling edge of pclk? My point here is that the pixelclk-inverted is not crystal clear thing, like the hsync/vsync/de-active values are. And while thinking about this, I realized that the meaning of pixelclk-inverted depends on what component is it applied to. Presuming normal pixclk means "pixel data on rising edge", the meaning of that depends on do we consider the SoC or the panel. The panel needs to sample the data on the other edge from the one the SoC uses to drive the data. Does the videomode describe the panel, or does it describe the settings programmed to the SoC? >> OMAP has the invert pclk setting, but it also has a setting to define >> when the sync signals are driven. The options are: >> - syncs are driven on rising edge of pclk >> - syncs are driven on falling edge of pclk >> - syncs are driven on the opposite edge of pclk compared to the pixel data >> >> For DE there's no setting, except the active high/low. >> >> And if I'm not mistaken, if the optional properties are not defined, >> they are not ignored, but left to the default 0. Which means active low, >> or active on rising edge(?). I think it would be good to have a >> "undefined" value for the properties. >> > > Yes. As mentioned in my other mail, the intention of the omitted properties do > not propagate properly. Omitted must be a value < 0, so it is clear in a later > stage, that this property shall not be used. And isn't unintentionally considered > to be active low. Ok. Just note that the values are currently stored into u32, and I don't think using negative error values with u32 is a good idea. >> I have some of the same concerns for this series than with the >> interpreted power sequences (on fbdev): when you publish the DT >> bindings, it's somewhat final version then, and fixing it later will be >> difficult. Of course, video modes are much clearer than the power >> sequences, so it's possible there won't be any problems with the DT >> bindings. >> > > The binding is pretty much at the bare minimum after a lot of discussion about > the properties. Even if the binding changes, I think it will rather grow than > shrink. Take the doubleclock property for example. It got here mistakingly, > because we had a display that has this feature. Right. That's why I would leave the pixelclock-inverted out for now, if we're not totally sure how it's defined. Of course, it could be just me who is not understanding the pixclk-inverted =). >> However, I'd still feel safer if the series would be split to non-DT and >> DT parts. The non-DT parts could be merged quite easily, and people >> could start using them in their kernels. This should expose >> bugs/problems related to the code. >> >> The DT part could be merged later, when there's confidence that the >> timings are good for all platforms. >> >> Or, alternatively, all the non-common bindings (de-active, pck >> invert,...) that are not used for fbdev or drm currently could be left >> out for now. But I'd stil prefer merging it in two parts. > > I don't say that I'm against it, but the whole reason for the series was > getting the display timings from a DT into a graphics driver. And I think > I remember seeing some other attempts at achieving this, but all specific > to one special case. There is even already a mainline driver that uses an older > version of the DT bindings (vt8500-fb). I think it'd be very useful even without DT bindings. But yes, I understand your need for it. You're now in v15 of the series. Are you sure v16 will be good enough to freeze the DT bindings, if 15 previous versions weren't? =). Perhaps I'm just overly cautious with DT bindings. APIs that are exposed outside the kernel scare me, as they should be just and not almost right. However, I want to also point out that where ever you're going to use the videomode DT bindings, when the common display framework is merged and presuming you'll use it, you may need to change the DT stuff again (for the SoC/gfx card, not the videomode bindings). Tomi
Attachment:
signature.asc
Description: OpenPGP digital signature
_______________________________________________ dri-devel mailing list dri-devel@xxxxxxxxxxxxxxxxxxxxx http://lists.freedesktop.org/mailman/listinfo/dri-devel
