ANX7688 is a USB Type-C port controller with a MUX. It converts HDMI 2.0 to DisplayPort 1.3 Ultra-HDi (4096x2160p60). The integrated crosspoint switch (the MUX) supports USB 3.1 data transfer along with the DisplayPort Alternate Mode signaling over USB Type-C. Additionally, an on-chip microcontroller (OCM) is available to manage the signal switching, Channel Configuration (CC) detection, USB Power Delivery (USB-PD), Vendor Defined Message (VDM) protocol support and other functions as defined in the USB TypeC and USB Power Delivery specifications. ANX7688 is found on Acer Chromebook R13 (elm) and on Pine64 PinePhone. Signed-off-by: Dafna Hirschfeld <dafna.hirschfeld@xxxxxxxxxxxxx> --- .../bindings/usb/analogix,anx7688.yaml | 177 ++++++++++++++++++ 1 file changed, 177 insertions(+) create mode 100644 Documentation/devicetree/bindings/usb/analogix,anx7688.yaml diff --git a/Documentation/devicetree/bindings/usb/analogix,anx7688.yaml b/Documentation/devicetree/bindings/usb/analogix,anx7688.yaml new file mode 100644 index 000000000000..6c4dd6b4b28b --- /dev/null +++ b/Documentation/devicetree/bindings/usb/analogix,anx7688.yaml @@ -0,0 +1,177 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/usb/analogix,anx7688.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Analogix ANX7688 Type-C Port Controller with HDMI to DP conversion + +maintainers: + - Nicolas Boichat <drinkcat@xxxxxxxxxxxx> + - Enric Balletbo i Serra <enric.balletbo@xxxxxxxxxxxxx> + +description: | + ANX7688 is a USB Type-C port controller with a MUX. It converts HDMI 2.0 to + DisplayPort 1.3 Ultra-HDi (4096x2160p60). + The integrated crosspoint switch (the MUX) supports USB 3.1 data transfer along with + the DisplayPort Alternate Mode signaling over USB Type-C. Additionally, + an on-chip microcontroller (OCM) is available to manage the signal switching, + Channel Configuration (CC) detection, USB Power Delivery (USB-PD), Vendor + Defined Message (VDM) protocol support and other functions as defined in the + USB TypeC and USB Power Delivery specifications. + + +properties: + compatible: + const: analogix,anx7688 + + reg: + maxItems: 1 + + avdd33-supply: + description: 3.3V Analog core supply voltage. + + dvdd18-supply: + description: 1.8V Digital I/O supply voltage. + + avdd18-supply: + description: 1.8V Analog core power supply voltage. + + avdd10-supply: + description: 1.0V Analog core power supply voltage. + + dvdd10-supply: + description: 1.0V Digital core supply voltage. + + hdmi5v-supply: + description: 5V power supply for the HDMI. + + hdmi_vt-supply: + description: Termination voltage for HDMI input. + + clocks: + description: The input clock specifier. + maxItems: 1 + + clock-names: + items: + - const: xtal + + hpd-gpios: + description: | + In USB Type-C applications, DP_HPD has no use. In standard DisplayPort + applications, DP_HPD is used as DP hot-plug. + maxItems: 1 + + enable-gpios: + description: Chip power down control. No internal pull-down or pull-up resistor. + maxItems: 1 + + reset-gpios: + description: Reset input signal. Active low. + maxItems: 1 + + vbus-det-gpios: + description: | + An input gpio for VBUS detection and high voltage detection, + external resistance divide VBUS voltage to 1/8. + maxItems: 1 + + interrupts: + description: | + The interrupt notifies 4 possible events - TCPC ALERT int, PD int, DP int, HDMI int. + maxItems: 1 + + cabledet-gpios: + description: An output gpio, indicates by the device that a cable is plugged. + maxItems: 1 + + vbus-ctrl-gpios: + description: + External VBUS power path. Enable VBUS source and disable VBUS sink or vice versa. + maxItems: 1 + + vconn-en1-gpios: + description: Controls the VCONN switch on the CC1 pin. + maxItems: 1 + + vconn-en2-gpios: + description: Controls the VCONN switch on the CC2 pin. + maxItems: 1 + + ports: + $ref: /schemas/graph.yaml#/properties/ports + + properties: + port@0: + $ref: /schemas/graph.yaml#/properties/port + description: Video port for HDMI input. + + port@1: + $ref: /schemas/graph.yaml#/properties/port + description: USB port for the USB3 input. + + port@2: + $ref: /schemas/graph.yaml#/properties/port + description: USB Type-c connector, see connector/usb-connector.yaml. + + required: + - port@0 + +required: + - compatible + - reg + +additionalProperties: false + +examples: + - | + #include <dt-bindings/gpio/gpio.h> + #include <dt-bindings/interrupt-controller/irq.h> + + i2c0 { + #address-cells = <1>; + #size-cells = <0>; + + anx7688: anx7688@2c { + compatible = "analogix,anx7688"; + reg = <0x2c>; + avdd33-supply = <®_dcdc1>; + dvdd18-supply = <®_ldo_io1>; + avdd18-supply = <®_ldo_io1>; + avdd10-supply = <®_anx1v0>; + dvdd10-supply = <®_anx1v0>; + hdmi_vt-supply = <®_dldo1>; + enable-gpios = <&pio 3 10 GPIO_ACTIVE_LOW>; /* PD10 */ + reset-gpios = <&pio 3 6 GPIO_ACTIVE_HIGH>; /* PD6 */ + interrupt-parent = <&r_pio>; + interrupts = <0 11 IRQ_TYPE_EDGE_FALLING>; /* PL11 */ + cabledet-gpios = <&r_pio 0 8 GPIO_ACTIVE_HIGH>; /* PL8 */ + vconn-en1-gpios = <&pio 3 9 GPIO_ACTIVE_LOW>; /* PD9 */ + vconn-en2-gpios = <&pio 3 9 GPIO_ACTIVE_LOW>; /* PD9 */ + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + anx7688_in0: endpoint { + remote-endpoint = <&hdmi0_out>; + }; + }; + + port@1 { + reg = <1>; + anx7688_in1: endpoint { + remote-endpoint = <&usbdrd_phy_ss>; + }; + }; + port@2 { + reg = <2>; + anx7688_out: endpoint { + remote-endpoint = <&typec_connector>; + }; + }; + }; + }; + }; -- 2.17.1 _______________________________________________ dri-devel mailing list dri-devel@xxxxxxxxxxxxxxxxxxxxx https://lists.freedesktop.org/mailman/listinfo/dri-devel
