Re: [PATCH v2 3/4] drm/bridge: ti-sn65dsi86: Read EDID blob over DDC

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



Quoting Doug Anderson (2020-11-02 08:06:14)
> On Sun, Nov 1, 2020 at 11:21 AM Laurent Pinchart
> <laurent.pinchart@xxxxxxxxxxxxxxxx> wrote:
> > On Thu, Oct 29, 2020 at 06:17:37PM -0700, Stephen Boyd wrote:
> > > @@ -265,6 +267,23 @@ connector_to_ti_sn_bridge(struct drm_connector *connector)
> > >  static int ti_sn_bridge_connector_get_modes(struct drm_connector *connector)
> > >  {
> > >       struct ti_sn_bridge *pdata = connector_to_ti_sn_bridge(connector);
> > > +     struct edid *edid = pdata->edid;
> > > +     int num, ret;
> > > +
> > > +     if (!edid) {
> > > +             pm_runtime_get_sync(pdata->dev);
> > > +             edid = pdata->edid = drm_get_edid(connector, &pdata->aux.ddc);
> > > +             pm_runtime_put(pdata->dev);
> > > +     }
> >
> > Do we need to cache the EDID ? It seems like something that should be
> > done by the DRM core (well, caching modes in that case), not by
> > individual bridge drivers.
> 
> I can take the blame for the fact that it does caching, since I
> requested it in early reviews.  In general boot speed is pretty
> important to me and each read of the EDID take 20 ms.  There are
> definitely several calls to get the EDID during a normal bootup.
> Stephen did a little more digging into exactly what was causing all
> these calls and can chime in, 

In ChromeOS we get modes a couple times and then whenever we connect or
disconnect a DP cable for external display we also get modes. It seems
that we also run modetest at boot but I'm not sure why we do that. I
think it is to gather diagnostic data for all the EDIDs on the device at
boot so we know what all is connected.

> but in general until we can eliminate
> the extra calls it seems like it'd be nice to keep the caching?  This
> bridge chip is intended for use for eDP for internal panels, so there
> should be no downside to caching.  If we can later optimize the DRM
> core, we can fix this and a pre-existing driver that does the same
> type of caching (analogix-anx6345.c) at the same time?

I'd like to add the caching somewhere in the core (maybe the bridge
connector code?) but I don't know what the logic should be. Is it eDP
and if not hpd notify then cache all the time and if it is eDP and hpd
notify then cache once hpd notify says detected and drop cache when no
longer detected?

	if (eDP) {
		if (!hpd)
			cache();
		else if (hpd_detected()) {
			cache();
		else if (!hpd_detected()) {
			drop_cache();
		}
	}

I thought that EDID could change and HPD can be pulsed to notify that it
should be read again.
_______________________________________________
dri-devel mailing list
dri-devel@xxxxxxxxxxxxxxxxxxxxx
https://lists.freedesktop.org/mailman/listinfo/dri-devel



[Index of Archives]     [Linux DRI Users]     [Linux Intel Graphics]     [Linux USB Devel]     [Video for Linux]     [Linux Audio Users]     [Yosemite News]     [Linux Kernel]     [Linux SCSI]     [XFree86]     [Linux USB Devel]     [Video for Linux]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [XFree86]
  Powered by Linux