Hello Sam,
thanks for your response.
On Sat, Oct 31, 2020 at 09:01:37AM +0100, Sam Ravnborg wrote:
> Hi Lubomir.
>
> On Fri, Oct 30, 2020 at 04:08:00AM +0100, Lubomir Rintel wrote:
> > Himax HX8837 is used to drive the LCD panel on OLPC platforms.
> >
> > It controls the panel backlight and is able to refresh it when the LCD
> > controller (and the rest of the plaform) is powered off.
> >
> > It also converts regular RGB color data from the LCDC so that it looks
> > reasonable on the OLPC LCD panel with a monochromatic layer on top of a
> > layer that can either reflect light (b/w sunlight readable mode) or light
> > pattern of red, green and blue pixels.
> >
> > At this point, the driver is rather basic. The self-refresh mode is not
> > supported. There's no way of independently controlling the color swizzling,
> > antialiasing or b/w conversion, but it probably isn't too useful either.
> >
> > There's another driver for the same hardware on OLPC XO-1.5 and XO-1.75
> > in drivers/staging/olpc_dcon. The display on that hardware doesn't utilize
> > DRM, so this driver doesn't replace the other one yet.
> >
> > Signed-off-by: Lubomir Rintel <lkundrak@xxxxx>
> >
> > ---
> > Changes since v5:
> > (All based on feedback from Sam Ravnborg)
> > - Fix indentation in Kconfig
> > - Sort #includes
> > - Use a constant for max brightness instead of a literal
> > - Remove struct drm_panel from priv data
> > - Use dev_err() instead of DRM_ERROR
> > - Replace direct use of backlight props.brightness with
> > backlight_get_brightness()
> > - Document sentinels with { /* sentinel */ }
> > - Remove unsetting of panel->backlight
>
> Thanks, I missed a few things during the last round, so here is a few
> more comments. Only very trivial things but lets get them fixed before
> we add the driver to drm-misc-next.
>
> Sam
>
> >
> > diff --git a/drivers/gpu/drm/bridge/Kconfig b/drivers/gpu/drm/bridge/Kconfig
> > index ef91646441b16..881780719af7c 100644
> > --- a/drivers/gpu/drm/bridge/Kconfig
> > +++ b/drivers/gpu/drm/bridge/Kconfig
> > @@ -48,6 +48,19 @@ config DRM_DISPLAY_CONNECTOR
> > on ARM-based platforms. Saying Y here when this driver is not needed
> > will not cause any issue.
> >
> > +config DRM_HIMAX_HX8837
> > + tristate "HiMax HX8837 OLPC Display Controller"
> > + depends on OF
> > + depends on OLPC || ARCH_MMP || COMPILE_TEST
> > + select DRM_KMS_HELPER
> > + select BACKLIGHT_LCD_SUPPORT
> Unknown symbol - "git grep BACKLIGHT_LCD_SUPPORT" only turned up one
> unrelated hit.
>
> > + select BACKLIGHT_CLASS_DEVICE
> Please use a depends - using select on a symbol with a prompt is always
> wrong. Yeah, I know you then need to enable backlight to see this
> driver. Sorry, but this is the best we can do now.
> Many other drivers can cope with depends here.
This results in a dependency loop:
drivers/video/fbdev/Kconfig:12:error: recursive dependency detected!
drivers/video/fbdev/Kconfig:12: symbol FB is selected by DRM_KMS_FB_HELPER
drivers/gpu/drm/Kconfig:80: symbol DRM_KMS_FB_HELPER depends on DRM_KMS_HELPER
drivers/gpu/drm/Kconfig:74: symbol DRM_KMS_HELPER is selected by DRM_HIMAX_HX8837
drivers/gpu/drm/bridge/Kconfig:51: symbol DRM_HIMAX_HX8837 depends on BACKLIGHT_CLASS_DEVICE
drivers/video/backlight/Kconfig:143: symbol BACKLIGHT_CLASS_DEVICE is selected by FB_BACKLIGHT
drivers/video/fbdev/Kconfig:187: symbol FB_BACKLIGHT depends on FB
Unfortunately I have no idea how to resolve it at the moment.
I suppose I can look further into it if necessary. Or is it okay if I
leave it at select BACKLIGHT_CLASS_DEVICE for now?
> > + help
> > + Enable support for HiMax HX8837 Display Controller as found in the
> > + OLPC XO laptops.
> > +
> > + If your laptop doesn't have green ears, say "N"
> I like this last comment :-)
>
> > +
> > config DRM_LONTIUM_LT9611
> > tristate "Lontium LT9611 DSI/HDMI bridge"
> > select SND_SOC_HDMI_CODEC if SND_SOC
> > diff --git a/drivers/gpu/drm/bridge/Makefile b/drivers/gpu/drm/bridge/Makefile
> > index 2b3aff104e466..21f72df3260db 100644
> > --- a/drivers/gpu/drm/bridge/Makefile
> > +++ b/drivers/gpu/drm/bridge/Makefile
> > @@ -2,6 +2,7 @@
> > obj-$(CONFIG_DRM_CDNS_DSI) += cdns-dsi.o
> > obj-$(CONFIG_DRM_CHRONTEL_CH7033) += chrontel-ch7033.o
> > obj-$(CONFIG_DRM_DISPLAY_CONNECTOR) += display-connector.o
> > +obj-$(CONFIG_DRM_HIMAX_HX8837) += himax-hx8837.o
> > obj-$(CONFIG_DRM_LONTIUM_LT9611) += lontium-lt9611.o
> > obj-$(CONFIG_DRM_LVDS_CODEC) += lvds-codec.o
> > obj-$(CONFIG_DRM_MEGACHIPS_STDPXXXX_GE_B850V3_FW) += megachips-stdpxxxx-ge-b850v3-fw.o
> > diff --git a/drivers/gpu/drm/bridge/himax-hx8837.c b/drivers/gpu/drm/bridge/himax-hx8837.c
> > new file mode 100644
> > index 0000000000000..f472e16cc331d
> > --- /dev/null
> > +++ b/drivers/gpu/drm/bridge/himax-hx8837.c
> > @@ -0,0 +1,330 @@
> > +// SPDX-License-Identifier: GPL-2.0-or-later
> > +/*
> > + * HiMax HX8837 Display Controller Driver
> > + *
> > + * Datasheet: http://wiki.laptop.org/images/0/09/DCON_datasheet_HX8837-A.pdf
> > + *
> > + * Copyright (C) 2020 Lubomir Rintel
> > + */
> > +
> > +#include <drm/drm_atomic_helper.h>
> > +#include <drm/drm_bridge.h>
> > +#include <drm/drm_of.h>
> > +#include <drm/drm_panel.h>
> > +#include <drm/drm_print.h>
> drm_print.h is no longer used and should be dropped.
>
> > +#include <drm/drm_probe_helper.h>
> > +
> > +#include <linux/gpio/consumer.h>
> > +#include <linux/module.h>
> > +#include <linux/regmap.h>
> > +
> > +#define bridge_to_hx8837_priv(x) \
> > + container_of(x, struct hx8837_priv, bridge)
> > +
> > +/* DCON registers */
> > +enum {
> > + DCON_REG_ID = 0x00,
> > + DCON_REG_MODE = 0x01,
> > + DCON_REG_HRES = 0x02,
> > + DCON_REG_HTOTAL = 0x03,
> > + DCON_REG_HSYNC_WIDTH = 0x04,
> > + DCON_REG_VRES = 0x05,
> > + DCON_REG_VTOTAL = 0x06,
> > + DCON_REG_VSYNC_WIDTH = 0x07,
> > + DCON_REG_TIMEOUT = 0x08,
> > + DCON_REG_SCAN_INT = 0x09,
> > + DCON_REG_BRIGHT = 0x0a,
> > + DCON_REG_MEM_OPT_A = 0x41,
> > + DCON_REG_MEM_OPT_B = 0x42,
> > +};
> > +
> > +/* DCON_REG_MODE */
> > +enum {
> > + MODE_PASSTHRU = BIT(0),
> > + MODE_SLEEP = BIT(1),
> > + MODE_SLEEP_AUTO = BIT(2),
> > + MODE_BL_ENABLE = BIT(3),
> > + MODE_BLANK = BIT(4),
> > + MODE_CSWIZZLE = BIT(5),
> > + MODE_COL_AA = BIT(6),
> > + MODE_MONO_LUMA = BIT(7),
> > + MODE_SCAN_INT = BIT(8),
> > + MODE_CLOCKDIV = BIT(9),
> > + MODE_DEBUG = BIT(14),
> > + MODE_SELFTEST = BIT(15),
> > +};
> > +
> > +/* DCON_REG_BRIGHT */
> > +enum {
> > + BRIGHT_MASK = GENMASK(7, 0),
> > +};
> > +
> > +struct hx8837_priv {
> > + struct device *dev;
> > + struct regmap *regmap;
> > + struct gpio_desc *load_gpio;
> > +
> > + struct drm_bridge *panel_bridge;
> > + struct drm_bridge bridge;
> > +};
> > +
> > +static int hx8837_bridge_attach(struct drm_bridge *bridge,
> > + enum drm_bridge_attach_flags flags)
> > +{
> > + struct hx8837_priv *priv = bridge_to_hx8837_priv(bridge);
> > +
> > + return drm_bridge_attach(bridge->encoder, priv->panel_bridge,
> > + bridge, flags);
> > +}
> > +
> > +static enum drm_mode_status hx8837_bridge_mode_valid(
> > + struct drm_bridge *bridge,
> > + const struct drm_display_info *info,
> > + const struct drm_display_mode *mode)
> > +{
> > + if (mode->hdisplay > 0xffff)
> > + return MODE_BAD_HVALUE;
> > + if (mode->htotal > 0xffff)
> > + return MODE_BAD_HVALUE;
> > + if (mode->hsync_start - mode->hdisplay > 0xff)
> > + return MODE_HBLANK_WIDE;
> > + if (mode->hsync_end - mode->hsync_start > 0xff)
> > + return MODE_HSYNC_WIDE;
> > + if (mode->vdisplay > 0xffff)
> > + return MODE_BAD_VVALUE;
> > + if (mode->vtotal > 0xffff)
> > + return MODE_BAD_VVALUE;
> > + if (mode->vsync_start - mode->vdisplay > 0xff)
> > + return MODE_VBLANK_WIDE;
> > + if (mode->vsync_end - mode->vsync_start > 0xff)
> > + return MODE_VSYNC_WIDE;
> > +
> > + return MODE_OK;
> > +}
> > +
> > +static void hx8837_bridge_disable(struct drm_bridge *bridge)
> > +{
> > + struct hx8837_priv *priv = bridge_to_hx8837_priv(bridge);
> > + int ret;
> > +
> > + ret = gpiod_direction_output(priv->load_gpio, 0);
> > + if (ret)
> > + dev_err(priv->dev, "error enabling the dcon load: %d\n", ret);
> I assume this is disabling the dcon load - so text needs an update
>
> > +
> > + ret = regmap_update_bits(priv->regmap, DCON_REG_MODE,
> > + MODE_PASSTHRU |
> > + MODE_SLEEP,
> > + MODE_PASSTHRU |
> > + MODE_SLEEP);
> > + if (ret)
> > + dev_err(priv->dev, "error disabling the dcon: %d\n", ret);
> > +}
> > +
> > +static void hx8837_bridge_enable(struct drm_bridge *bridge)
> > +{
> > + struct hx8837_priv *priv = bridge_to_hx8837_priv(bridge);
> > + int ret;
> > +
> > + ret = regmap_update_bits(priv->regmap, DCON_REG_MODE,
> > + MODE_PASSTHRU |
> > + MODE_SLEEP |
> > + MODE_SLEEP_AUTO |
> > + MODE_BLANK |
> > + MODE_SCAN_INT |
> > + MODE_CLOCKDIV |
> > + MODE_DEBUG |
> > + MODE_SELFTEST,
> > + MODE_PASSTHRU);
> > + if (ret)
> > + dev_err(priv->dev, "error enabling the dcon: %d\n", ret);
> > +
> > + ret = gpiod_direction_output(priv->load_gpio, 1);
> > + if (ret)
> > + dev_err(priv->dev, "error enabling the dcon load: %d\n", ret);
> > +}
> > +
> > +static void hx8837_bridge_mode_set(struct drm_bridge *bridge,
> > + const struct drm_display_mode *mode,
> > + const struct drm_display_mode *adjusted_mode)
> > +{
> > + struct hx8837_priv *priv = bridge_to_hx8837_priv(bridge);
> > +
> > + regmap_write(priv->regmap, DCON_REG_HRES, mode->hdisplay);
> > + regmap_write(priv->regmap, DCON_REG_HTOTAL, mode->htotal);
> > + regmap_write(priv->regmap, DCON_REG_HSYNC_WIDTH,
> > + (mode->hsync_start - mode->hdisplay) << 8 |
> > + (mode->hsync_end - mode->hsync_start));
> > + regmap_write(priv->regmap, DCON_REG_VRES, mode->vdisplay);
> > + regmap_write(priv->regmap, DCON_REG_VTOTAL, mode->vtotal);
> > + regmap_write(priv->regmap, DCON_REG_VSYNC_WIDTH,
> > + (mode->vsync_start - mode->vdisplay) << 8 |
> > + (mode->vsync_end - mode->vsync_start));
> > +}
> > +
> > +static const struct drm_bridge_funcs hx8837_bridge_funcs = {
> > + .attach = hx8837_bridge_attach,
> > + .mode_valid = hx8837_bridge_mode_valid,
> > + .disable = hx8837_bridge_disable,
> > + .enable = hx8837_bridge_enable,
> > + .mode_set = hx8837_bridge_mode_set,
> > +};
> > +
> > +static int hx8837_bl_update_status(struct backlight_device *bl)
> > +{
> > + struct hx8837_priv *priv = bl_get_data(bl);
> > + unsigned int val;
> > + int ret;
> > +
> > + ret = regmap_update_bits(priv->regmap, DCON_REG_BRIGHT,
> > + BRIGHT_MASK,
> > + backlight_get_brightness(bl));
> > + if (ret) {
> > + dev_err(&bl->dev, "error setting the backlight: %d\n", ret);
> > + return ret;
> > + }
> > +
> > + if (backlight_get_brightness(bl))
> > + val = MODE_CSWIZZLE | MODE_COL_AA;
> > + else
> > + val = MODE_MONO_LUMA;
> > +
> > + ret = regmap_update_bits(priv->regmap, DCON_REG_MODE,
> > + MODE_CSWIZZLE |
> > + MODE_COL_AA |
> > + MODE_MONO_LUMA,
> > + val);
> > + if (ret) {
> > + dev_err(&bl->dev, "error setting color mode: %d\n", ret);
> > + return ret;
> > + }
> > +
> > + return 0;
> > +}
> > +
> > +static const struct backlight_ops hx8837_bl_ops = {
> > + .update_status = hx8837_bl_update_status,
> > +};
> > +
> > +static const struct regmap_config hx8837_regmap_config = {
> > + .reg_bits = 8,
> > + .val_bits = 16,
> > + .max_register = 0x4c,
> > + .val_format_endian = REGMAP_ENDIAN_LITTLE,
> > +};
> > +
> > +static int hx8837_probe(struct i2c_client *client,
> > + const struct i2c_device_id *id)
> > +{
> > + struct backlight_properties bl_props = {
> > + .type = BACKLIGHT_RAW,
> > + .max_brightness = BRIGHT_MASK,
> > + };
> I have recently learned we shall also always set the scale.
> This is missing in many drivers - but please do it here.
>
> > + struct device *dev = &client->dev;
> > + struct backlight_device *bl;
> > + struct hx8837_priv *priv;
> > + struct drm_panel *panel;
> > + unsigned int val;
> > + int ret;
> > +
> > + priv = devm_kzalloc(dev, sizeof(*priv), GFP_KERNEL);
> > + if (!priv)
> > + return -ENOMEM;
> > +
> > + dev_set_drvdata(dev, priv);
> > + priv->dev = dev;
> > +
> > + priv->load_gpio = devm_gpiod_get(dev, "load", GPIOD_ASIS);
> > + if (IS_ERR(priv->load_gpio))
> > + return PTR_ERR(priv->load_gpio);
> > +
> > + ret = drm_of_find_panel_or_bridge(dev->of_node, 1, -1, &panel, NULL);
> > + if (ret)
> > + return ret;
> > +
> > + if (panel->backlight) {
> > + dev_err(dev, "the panel already has a backlight controller\n");
> > + return -ENODEV;
> > + }
> > +
> > + priv->panel_bridge = devm_drm_panel_bridge_add(dev, panel);
> > + if (IS_ERR(priv->panel_bridge))
> > + return PTR_ERR(priv->panel_bridge);
> > +
> > + priv->regmap = devm_regmap_init_i2c(client, &hx8837_regmap_config);
> > + if (IS_ERR(priv->regmap)) {
> > + dev_err(dev, "regmap init failed\n");
> regmap_init_i2c failed?
>
> > + return PTR_ERR(priv->regmap);
> > + }
> > +
> > + ret = regmap_read(priv->regmap, DCON_REG_ID, &val);
> > + if (ret < 0) {
> > + dev_err(dev, "error reading the model id: %d\n", ret);
> > + return ret;
> > + }
> > + if ((val & 0xff00) != 0xdc00) {
> > + dev_err(dev, "the device is not a hx8837\n");
> > + return -ENODEV;
> > + }
> > +
> > + ret = regmap_read(priv->regmap, DCON_REG_BRIGHT, &val);
> > + if (ret < 0) {
> > + dev_err(&bl->dev, "error getting the backlight: %d\n", ret);
> > + return ret;
> > + }
> > + bl_props.brightness = val & 0xf;
> > +
> > + bl = devm_backlight_device_register(dev, dev_name(dev), dev, priv,
> > + &hx8837_bl_ops, &bl_props);
> > + if (IS_ERR(bl)) {
> > + dev_err(dev, "failed to register backlight\n");
> > + return PTR_ERR(bl);
> > + }
> > +
> > + panel->backlight = bl;
> > +
> > + INIT_LIST_HEAD(&priv->bridge.list);
> > + priv->bridge.funcs = &hx8837_bridge_funcs;
> > + priv->bridge.of_node = dev->of_node;
> > + drm_bridge_add(&priv->bridge);
> > +
> > + dev_info(dev, "HiMax HX8837 Display Controller Driver\n");
> Debug - not needed
> > + return 0;
> > +}
> > +
> > +static int hx8837_remove(struct i2c_client *client)
> > +{
> > + struct device *dev = &client->dev;
> > + struct hx8837_priv *priv = dev_get_drvdata(dev);
> > +
> > + drm_bridge_remove(&priv->bridge);
> > +
> > + return 0;
> > +}
> > +
> > +static const struct of_device_id hx8837_dt_ids[] = {
> > + { .compatible = "himax,hx8837", },
> > + { /* sentinel */ }
> > +};
> > +MODULE_DEVICE_TABLE(of, hx8837_dt_ids);
> > +
> > +static const struct i2c_device_id hx8837_ids[] = {
> > + { "hx8837", 0 },
> > + { /* sentinel */ }
> > +};
> > +MODULE_DEVICE_TABLE(i2c, hx8837_ids);
> > +
> > +static struct i2c_driver hx8837_driver = {
> > + .probe = hx8837_probe,
> > + .remove = hx8837_remove,
> > + .driver = {
> > + .name = "hx8837",
> > + .of_match_table = of_match_ptr(hx8837_dt_ids),
> > + },
> > + .id_table = hx8837_ids,
> > +};
> > +
> > +module_i2c_driver(hx8837_driver);
> > +
> > +MODULE_AUTHOR("Lubomir Rintel <lkundrak@xxxxx>");
> > +MODULE_DESCRIPTION("HiMax HX8837 Display Controller Driver");
> > +MODULE_LICENSE("GPL");
> > --
> > 2.28.0
_______________________________________________
dri-devel mailing list
dri-devel@xxxxxxxxxxxxxxxxxxxxx
https://lists.freedesktop.org/mailman/listinfo/dri-devel
