On Fri, Jul 17, 2020 at 03:37:44PM +0200, Hans de Goede wrote:
> While looking into adding atomic-pwm support to the pwm-crc driver I
> noticed something odd, there is a PWM_BASE_CLK define of 6 MHz and
> there is a clock-divider which divides this with a value between 1-128,
> and there are 256 duty-cycle steps.
>
> The pwm-crc code before this commit assumed that a clock-divider
> setting of 1 means that the PWM output is running at 6 MHZ, if that
> is true, where do these 256 duty-cycle steps come from?
>
> This would require an internal frequency of 256 * 6 MHz = 1.5 GHz, that
> seems unlikely for a PMIC which is using a silicon process optimized for
> power-switching transistors. It is way more likely that there is an 8
> bit counter for the duty cycle which acts as an extra fixed divider
> wrt the PWM output frequency.
>
> The main user of the pwm-crc driver is the i915 GPU driver which uses it
> for backlight control. Lets compare the PWM register values set by the
> video-BIOS (the GOP), assuming the extra fixed divider is present versus
> the PWM frequency specified in the Video-BIOS-Tables:
>
> Device: PWM Hz set by BIOS PWM Hz specified in VBT
> Asus T100TA 200 200
> Asus T100HA 200 200
> Lenovo Miix 2 8 23437 20000
> Toshiba WT8-A 23437 20000
>
> So as we can see if we assume the extra division by 256 then the register
> values set by the GOP are an exact match for the VBT values, where as
> otherwise the values would be of by a factor of 256.
>
> This commit fixes the period / duty_cycle calculations to take the
> extra division by 256 into account.
So, base clock is 6MHz, then 7 bit divisor. That's what original values
were for. On top of that there is 8-bit duty cycle control ("divide by 256"
whatever it means) with the output range 23.437kHz..183Hz.
>
> Signed-off-by: Hans de Goede <hdegoede@xxxxxxxxxx>
> ---
> Changes in v3:
> - Use NSEC_PER_USEC instead of adding a new (non-sensical) NSEC_PER_MHZ define
> ---
> drivers/pwm/pwm-crc.c | 6 +++---
> 1 file changed, 3 insertions(+), 3 deletions(-)
>
> diff --git a/drivers/pwm/pwm-crc.c b/drivers/pwm/pwm-crc.c
> index 272eeb071147..c056eb9b858c 100644
> --- a/drivers/pwm/pwm-crc.c
> +++ b/drivers/pwm/pwm-crc.c
> @@ -21,8 +21,8 @@
>
> #define PWM_MAX_LEVEL 0xFF
>
> -#define PWM_BASE_CLK 6000000 /* 6 MHz */
> -#define PWM_MAX_PERIOD_NS 21333 /* 46.875KHz */
> +#define PWM_BASE_CLK_MHZ 6 /* 6 MHz */
> +#define PWM_MAX_PERIOD_NS 5461333 /* 183 Hz */
>
> /**
> * struct crystalcove_pwm - Crystal Cove PWM controller
> @@ -72,7 +72,7 @@ static int crc_pwm_config(struct pwm_chip *c, struct pwm_device *pwm,
>
> /* changing the clk divisor, need to disable fisrt */
> crc_pwm_disable(c, pwm);
> - clk_div = PWM_BASE_CLK * period_ns / NSEC_PER_SEC;
> + clk_div = PWM_BASE_CLK_MHZ * period_ns / (256 * NSEC_PER_USEC);
>
> regmap_write(crc_pwm->regmap, PWM0_CLK_DIV,
> clk_div | PWM_OUTPUT_ENABLE);
> --
> 2.26.2
>
--
With Best Regards,
Andy Shevchenko
_______________________________________________
dri-devel mailing list
dri-devel@xxxxxxxxxxxxxxxxxxxxx
https://lists.freedesktop.org/mailman/listinfo/dri-devel
