Hi,
On Tue, Jul 14, 2020 at 03:13:05PM +0800, Chen-Yu Tsai wrote:
> From: Chen-Yu Tsai <wens@xxxxxxxx>
>
> The Primo73 is an MSI branded Allwinner A20-based 7-inch tablet. It has
> a metal back case with a plastic insert around where the WiFi antenna is.
> The tablet is (as of July of 2020) no longer available from retailers.
> Kernel sources (as required by GPL) are no longer available from the
> vendor, MSI. The device support page still lists the link, but it is
> dead.
>
> The tablet features a non-identifiable 1024x600 7" MIPI DPI TFT panel,
> Goodix GT911-based capacitive touchscreen, 1GB DRAM, 8GB MLC NAND,
> RTL8188ETV-based WiFi, an NXP MMA8452 accelerometer for orientation,
> a GC2035 2 megapixel rear camera, a GC0308 0.3 megapixel front camera,
> a mini-HDMI output, a micro-USB port, a headphone jack and single speaker.
>
> The board design is believe to follow Allwinner's reference design. This
> judgement is based on the fact that the I/O pins and GPIO lines used
> match up with the reference design. Assumptions about the regulator tree
> are based on this.
>
> The LCD panel only has some serial number markings, and what appears to
> be a part number: "OS1N71J003", which is also a prefix for one of the
> serial number markings. Searching for this part number yielded no
> results. As such, the color depth display timings are directly listed
> in the device tree. The timing are from the FEX file recovered from the
> device. The color depth was derived from the dithering setting from the
> FEX file, as well as independent testing with a color gradient image.
> The internal board, as well as the ribbon cable for the panel, route the
> full 24 bits of color. So the 2 extra bits are dropped either by the
> panel itself or somewhere within the LCD panel module casing.
>
> Add a device tree for this tablet. Almost the whole device is supported.
> The only things missing are the two cameras, which don't have device
> tree bindings or driver support. The vendor for the LCD panel is left
> out, since there is nothing to go with.
>
> Signed-off-by: Chen-Yu Tsai <wens@xxxxxxxx>
> ---
>
> The panel-dpi binding requires a more-specific compatible string.
> However given the vendor of the panel is unknown, I'm not sure what
> the best course of action is here. I opted to put the part number in
> without a vendor prefix.
I guess we could just make up a comptible from the tablet name here?
Something like msi,primo73-panel ?
> ---
> arch/arm/boot/dts/Makefile | 1 +
> arch/arm/boot/dts/sun7i-a20-primo73.dts | 279 ++++++++++++++++++++++++
> 2 files changed, 280 insertions(+)
> create mode 100644 arch/arm/boot/dts/sun7i-a20-primo73.dts
>
> diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
> index e6a1cac0bfc7..c09cda958db5 100644
> --- a/arch/arm/boot/dts/Makefile
> +++ b/arch/arm/boot/dts/Makefile
> @@ -1133,6 +1133,7 @@ dtb-$(CONFIG_MACH_SUN7I) += \
> sun7i-a20-orangepi-mini.dtb \
> sun7i-a20-pcduino3.dtb \
> sun7i-a20-pcduino3-nano.dtb \
> + sun7i-a20-primo73.dtb \
> sun7i-a20-wexler-tab7200.dtb \
> sun7i-a20-wits-pro-a20-dkt.dtb
> dtb-$(CONFIG_MACH_SUN8I) += \
> diff --git a/arch/arm/boot/dts/sun7i-a20-primo73.dts b/arch/arm/boot/dts/sun7i-a20-primo73.dts
> new file mode 100644
> index 000000000000..f3b1002ceb50
> --- /dev/null
> +++ b/arch/arm/boot/dts/sun7i-a20-primo73.dts
> @@ -0,0 +1,279 @@
> +// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
> +/*
> + * Copyright (C) 2020 Chen-Yu Tsai <wens@xxxxxxxx>
> + */
> +
> +/dts-v1/;
> +#include "sun7i-a20.dtsi"
> +#include "sunxi-common-regulators.dtsi"
> +
> +#include <dt-bindings/gpio/gpio.h>
> +#include <dt-bindings/input/input.h>
> +#include <dt-bindings/interrupt-controller/irq.h>
> +#include <dt-bindings/pwm/pwm.h>
> +
> +/{
> + model = "MSI Primo73 Tablet";
> + compatible = "msi,primo73", "allwinner,sun7i-a20";
> +
> + aliases {
> + serial0 = &uart0;
> + };
> +
> + backlight: backlight {
> + compatible = "pwm-backlight";
> + pwms = <&pwm 0 50000 PWM_POLARITY_INVERTED>;
> + enable-gpios = <&pio 7 7 GPIO_ACTIVE_HIGH>; /* PH7 */
> + };
> +
> + chosen {
> + stdout-path = "serial0:115200n8";
> + };
> +
> + hdmi-connector {
> + compatible = "hdmi-connector";
> + type = "b";
> +
> + port {
> + hdmi_con_in: endpoint {
> + remote-endpoint = <&hdmi_out_con>;
> + };
> + };
> + };
> +
> + panel: panel {
> + compatible = "os1n71j003", "panel-dpi";
> + backlight = <&backlight>;
> + power-supply = <®_vcc5v0>; /* Actually driven from IPSOUT */
> + enable-gpios = <&pio 7 8 GPIO_ACTIVE_HIGH>; /* PH8 */
> + height-mm = <86>;
> + width-mm = <155>;
> + bits-per-color = <6>;
> +
> + panel-timing {
> + clock-frequency = <60000000>;
> + hactive = <1024>;
> + vactive = <600>;
> + hfront-porch = <160>;
> + hback-porch = <60>;
> + hsync-len = <100>;
> + vback-porch = <13>;
> + vfront-porch = <10>;
> + vsync-len = <10>;
> + de-active = <1>;
> + pixelclk-active = <0>;
> + };
The clock frequency doesn't seem to match the rest of the timings
though, it should be around 51MHz. Was this taken from the fex file too?
Maxime
Attachment:
signature.asc
Description: PGP signature
_______________________________________________ dri-devel mailing list dri-devel@xxxxxxxxxxxxxxxxxxxxx https://lists.freedesktop.org/mailman/listinfo/dri-devel
