From: Marek Vasut <marex@xxxxxxx>
Add driver for the ITE IT6251 LVDS-to-eDP bridge.
Signed-off-by: Marek Vasut <marex@xxxxxxx>
Signed-off-by: Richard Marko <srk@xxxxx>
Cc: Daniel Vetter <daniel@xxxxxxxx>
Cc: Sean Cross <xobs@xxxxxxxxxx>
To: dri-devel@xxxxxxxxxxxxxxxxxxxxx
---
drivers/gpu/drm/bridge/Kconfig | 12 +
drivers/gpu/drm/bridge/Makefile | 1 +
drivers/gpu/drm/bridge/ite-it6251.c | 582 ++++++++++++++++++++++++++++
3 files changed, 595 insertions(+)
create mode 100644 drivers/gpu/drm/bridge/ite-it6251.c
diff --git a/drivers/gpu/drm/bridge/Kconfig b/drivers/gpu/drm/bridge/Kconfig
index aaed2347ace9..934896a4ab2d 100644
--- a/drivers/gpu/drm/bridge/Kconfig
+++ b/drivers/gpu/drm/bridge/Kconfig
@@ -38,6 +38,18 @@ config DRM_DISPLAY_CONNECTOR
on ARM-based platforms. Saying Y here when this driver is not needed
will not cause any issue.
+config DRM_ITE_IT6251
+ tristate "ITE IT6251 LVDS/eDP bridge"
+ depends on OF
+ select DRM_KMS_HELPER
+ select DRM_PANEL
+ select REGMAP_I2C
+ help
+ Driver for ITE IT6251 LVDS-eDP bridge chip driver. This is used
+ in Novena open-hardware laptop with eDP based panel.
+ IT6251 supports LVDS input and DisplayPort 1.1a output,
+ resolution up to 1080P and 10-bit color depth.
+
config DRM_LVDS_CODEC
tristate "Transparent LVDS encoders and decoders support"
depends on OF
diff --git a/drivers/gpu/drm/bridge/Makefile b/drivers/gpu/drm/bridge/Makefile
index 6fb062b5b0f0..4c195dc42fce 100644
--- a/drivers/gpu/drm/bridge/Makefile
+++ b/drivers/gpu/drm/bridge/Makefile
@@ -1,6 +1,7 @@
# SPDX-License-Identifier: GPL-2.0
obj-$(CONFIG_DRM_CDNS_DSI) += cdns-dsi.o
obj-$(CONFIG_DRM_DISPLAY_CONNECTOR) += display-connector.o
+obj-$(CONFIG_DRM_ITE_IT6251) += ite-it6251.o
obj-$(CONFIG_DRM_LVDS_CODEC) += lvds-codec.o
obj-$(CONFIG_DRM_MEGACHIPS_STDPXXXX_GE_B850V3_FW) += megachips-stdpxxxx-ge-b850v3-fw.o
obj-$(CONFIG_DRM_NXP_PTN3460) += nxp-ptn3460.o
diff --git a/drivers/gpu/drm/bridge/ite-it6251.c b/drivers/gpu/drm/bridge/ite-it6251.c
new file mode 100644
index 000000000000..b8534fb62c9d
--- /dev/null
+++ b/drivers/gpu/drm/bridge/ite-it6251.c
@@ -0,0 +1,582 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Copyright (C) 2014 Sean Cross <xobs@xxxxxxxxxx>
+ *
+ * Rework for mainline: Marek Vasut <marex@xxxxxxx>
+ */
+
+#include <linux/delay.h>
+#include <linux/i2c.h>
+#include <linux/module.h>
+#include <linux/of_gpio.h>
+#include <linux/of_graph.h>
+#include <linux/of_platform.h>
+#include <linux/regmap.h>
+#include <linux/regulator/consumer.h>
+#include <drm/drm_panel.h>
+
+#include <drm/drm_atomic_helper.h>
+#include <drm/drm_bridge.h>
+#include <drm/drm_connector.h>
+#include <drm/drm_crtc.h>
+#include <drm/drm_crtc_helper.h>
+#include <drm/drm_print.h>
+#include <drm/drm_probe_helper.h>
+
+struct it6251_bridge {
+ struct i2c_client *client;
+ struct i2c_client *lvds_client;
+ struct regmap *regmap;
+ struct regmap *lvds_regmap;
+ struct regulator *regulator;
+
+ struct drm_connector connector;
+ struct drm_bridge bridge;
+ struct drm_panel *panel;
+};
+
+/* Register definitions */
+#define IT6251_VENDOR_ID_LOW 0x00
+#define IT6251_VENDOR_ID_HIGH 0x01
+#define IT6251_DEVICE_ID_LOW 0x02
+#define IT6251_DEVICE_ID_HIGH 0x03
+#define IT6251_SYSTEM_STATUS 0x0d
+#define IT6251_SYSTEM_STATUS_RINTSTATUS BIT(0)
+#define IT6251_SYSTEM_STATUS_RHPDSTATUS BIT(1)
+#define IT6251_SYSTEM_STATUS_RVIDEOSTABLE BIT(2)
+#define IT6251_SYSTEM_STATUS_RPLL_IOLOCK BIT(3)
+#define IT6251_SYSTEM_STATUS_RPLL_XPLOCK BIT(4)
+#define IT6251_SYSTEM_STATUS_RPLL_SPLOCK BIT(5)
+#define IT6251_SYSTEM_STATUS_RAUXFREQ_LOCK BIT(6)
+#define IT6251_REF_STATE 0x0e
+#define IT6251_REF_STATE_MAIN_LINK_DISABLED BIT(0)
+#define IT6251_REF_STATE_AUX_CHANNEL_READ BIT(1)
+#define IT6251_REF_STATE_CR_PATTERN BIT(2)
+#define IT6251_REF_STATE_EQ_PATTERN BIT(3)
+#define IT6251_REF_STATE_NORMAL_OPERATION BIT(4)
+#define IT6251_REF_STATE_MUTED BIT(5)
+#define IT6251_RPCLK_CNT_LOW 0x13
+#define IT6251_RPCLK_CNT_HIGH 0x14
+#define IT6251_RPC_REQ 0x2b
+#define IT6251_RPC_REQ_RPC_FIFOFULL BIT(6)
+#define IT6251_RPC_REQ_RPC_FIFOEMPTY BIT(7)
+#define IT6251_PCLK_CNT_LOW 0x57
+#define IT6251_PCLK_CNT_HIGH 0x58
+#define IT6251_DPHDEW_LOW 0xa5
+#define IT6251_DPHDEW_HIGH 0xa6
+#define IT6251_DPVDEW_LOW 0xaf
+#define IT6251_DPVDEW_HIGH 0xb0
+#define IT6251_LVDS_PORT_ADDR 0xfd
+#define IT6251_LVDS_PORT_CTRL 0xfe
+#define IT6251_LVDS_PORT_CTRL_EN BIT(0)
+
+/*
+ * Register programming sequences.
+ * NOTE: There is a lot of registers here which are completely undocumented
+ * and/or their meaning is not clear from the little documentation
+ * that is available for this chip. These values below just seem to
+ * work well enough.
+ */
+static const struct reg_sequence it6251_lvds_rx_sequence[] = {
+ { 0x05, 0x00 },
+
+ { 0x3b, 0x42 }, /* reset LVDSRX PLL */
+ { 0x3b, 0x43 },
+
+ { 0x3c, 0x08 }, /* something with SSC PLL */
+ { 0x0b, 0x88 }, /* don't swap links, writing reserved regs */
+
+ { 0x2c, 0x01 }, /* JEIDA, 8-bit depth 0x11, original 0x42 */
+ { 0x32, 0x04 }, /* "reserved" */
+ { 0x35, 0xe0 }, /* "reserved" */
+ { 0x2b, 0x24 }, /* "reserved" + clock delay */
+
+ { 0x05, 0x02 }, /* reset LVDSRX pix clock */
+ { 0x05, 0x00 },
+};
+
+static const struct reg_sequence it6251_edp_tx_sequence[] = {
+ /* two lane mode, normal operation, no swapping, no downspread */
+ { 0x16, 0x02 },
+ { 0x23, 0x40 }, /* some AUX channel EDID magic */
+ { 0x5c, 0xf3 }, /* power down lanes 3-0 */
+ { 0x5f, 0x06 }, /* enable DP scrambling, change EQ CR phase */
+ { 0x60, 0x02 }, /* color mode RGB, pclk/2 */
+ { 0x61, 0x04 }, /* dual pixel input mode, no EO swap, no RGB swap */
+ { 0x62, 0x01 }, /* M444B24 video format */
+
+ /* vesa range / not interlace / vsync high / hsync high */
+ { 0xa0, 0x0F },
+
+ { 0xc9, 0xf5 }, /* hpd event timer set to 1.6-ish ms */
+
+ { 0xca, 0x4d }, /* more reserved magic */
+ { 0xcb, 0x37 },
+
+ /* enhanced framing mode, auto video fifo reset, video mute disable */
+ { 0xd3, 0x03 },
+ { 0xd4, 0x45 }, /* "vidstmp" and some reserved stuff */
+
+ { 0xe7, 0xa0 }, /* queue number -- reserved */
+ { 0xe8, 0x33 }, /* info frame packets and reserved */
+ { 0xec, 0x00 }, /* more AVI stuff */
+
+ { 0x23, 0x42 }, /* select PC master reg for aux channel? */
+
+ { 0x24, 0x00 }, /* send PC request commands */
+ { 0x25, 0x00 },
+ { 0x26, 0x00 },
+
+ { 0x2b, 0x00 }, /* native aux read */
+ { 0x23, 0x40 }, /* back to internal */
+
+ { 0x19, 0xff }, /* voltage swing level 3 */
+ { 0x1a, 0xff }, /* pre-emphasis level 3 */
+
+ { 0x17, 0x01 }, /* start link training */
+};
+
+static struct it6251_bridge *bridge_to_it6251(struct drm_bridge *bridge)
+{
+ return container_of(bridge, struct it6251_bridge, bridge);
+}
+
+static struct it6251_bridge *conn_to_it6251(struct drm_connector *connector)
+{
+ return container_of(connector, struct it6251_bridge, connector);
+}
+
+static int it6251_is_stable(struct it6251_bridge *it6251)
+{
+ unsigned int status, rpclkcnt, clkcnt, refstate, rpcreq;
+ u16 hactive;
+ u16 vactive;
+ u8 regs[2];
+ int ret;
+
+ ret = regmap_read(it6251->regmap, IT6251_SYSTEM_STATUS, &status);
+ if (ret)
+ return ret;
+ dev_dbg(&it6251->client->dev, "System status: 0x%02x\n", status);
+
+ if (!(status & IT6251_SYSTEM_STATUS_RVIDEOSTABLE))
+ return -EINVAL;
+
+ ret = regmap_bulk_read(it6251->regmap, IT6251_RPCLK_CNT_LOW, regs, 2);
+ if (ret)
+ return ret;
+ rpclkcnt = (regs[0] & 0xff) | ((regs[1] & 0x0f) << 8);
+ dev_dbg(&it6251->client->dev, "RPCLKCnt: %d\n", rpclkcnt);
+
+ ret = regmap_bulk_read(it6251->lvds_regmap, IT6251_PCLK_CNT_LOW,
+ regs, 2);
+ if (ret)
+ return ret;
+ clkcnt = (regs[0] & 0xff) | ((regs[1] & 0x0f) << 8);
+ dev_dbg(&it6251->client->dev, "Clock: 0x%02x\n", clkcnt);
+
+ ret = regmap_read(it6251->lvds_regmap, IT6251_REF_STATE, &refstate);
+ if (ret)
+ return ret;
+ dev_dbg(&it6251->client->dev, "Ref Link State: 0x%02x\n", refstate);
+
+ ret = regmap_read(it6251->lvds_regmap, IT6251_RPC_REQ, &rpcreq);
+ if (ret)
+ return ret;
+ dev_dbg(&it6251->client->dev, "RPC Req: 0x%02x\n", rpcreq);
+
+ ret = regmap_bulk_read(it6251->regmap, IT6251_DPHDEW_LOW, regs, 2);
+ if (ret)
+ return ret;
+ hactive = (regs[0] & 0xff) | ((regs[1] & 0x1f) << 8);
+ dev_dbg(&it6251->client->dev, "hactive: %d\n", hactive);
+
+ ret = regmap_bulk_read(it6251->regmap, IT6251_DPVDEW_LOW, regs, 2);
+ if (ret)
+ return ret;
+ vactive = (regs[0] & 0xff) | ((regs[1] & 0x0f) << 8);
+ dev_dbg(&it6251->client->dev, "vactive: %d\n", vactive);
+
+ if ((refstate & 0x1f) != 0)
+ return -EINVAL;
+
+ if (rpcreq & IT6251_RPC_REQ_RPC_FIFOFULL) {
+ dev_err(&it6251->client->dev,
+ "RPC fifofull is set, might be an error\n");
+ return -EINVAL;
+ }
+
+ /* If video is muted, that's a failure */
+ if (refstate & IT6251_REF_STATE_MUTED)
+ return -EINVAL;
+
+ return 0;
+}
+
+static int it6251_init(struct it6251_bridge *it6251)
+{
+ const struct reg_sequence it6251_reset_reg_sequence[] = {
+ { 0x05, 0x00 },
+ { IT6251_LVDS_PORT_ADDR, it6251->lvds_client->addr << 1 },
+ { IT6251_LVDS_PORT_CTRL, IT6251_LVDS_PORT_CTRL_EN },
+ };
+
+ int ret, stable_delays;
+ unsigned int reg;
+
+ /*
+ * Reset DisplayPort half. Setting bit 2 causes IT6251 to not
+ * respond over i2c, which is considered "normal". This write
+ * will report failure, but will actually succeed.
+ */
+ regmap_write(it6251->regmap, 0x05, 0xff);
+
+ /* Un-reset DisplayPort half and configure LVDS receiver. */
+ ret = regmap_multi_reg_write(it6251->regmap, it6251_reset_reg_sequence,
+ ARRAY_SIZE(it6251_reset_reg_sequence));
+ if (ret) {
+ dev_err(&it6251->client->dev, "cannot setup eDP half\n");
+ return ret;
+ }
+
+ /* LVDS RX */
+ regmap_write(it6251->lvds_regmap, 0x05, 0xff);
+ ret = regmap_multi_reg_write(it6251->lvds_regmap,
+ it6251_lvds_rx_sequence,
+ ARRAY_SIZE(it6251_lvds_rx_sequence));
+ if (ret) {
+ dev_err(&it6251->lvds_client->dev, "cannot setup LVDS RX\n");
+ return ret;
+ }
+
+ /* eDP TX */
+ ret = regmap_multi_reg_write(it6251->regmap,
+ it6251_edp_tx_sequence,
+ ARRAY_SIZE(it6251_edp_tx_sequence));
+ if (ret) {
+ dev_err(&it6251->client->dev, "cannot setup eDP TX\n");
+ return ret;
+ }
+
+ for (stable_delays = 0; stable_delays < 100; stable_delays++) {
+ ret = regmap_read(it6251->regmap, 0x0e, ®);
+ if (ret || ((reg & 0x1f) != 0x10)) {
+ mdelay(2);
+ continue;
+ }
+
+ ret = regmap_read(it6251->regmap, IT6251_SYSTEM_STATUS, ®);
+ if (ret || !(reg & IT6251_SYSTEM_STATUS_RVIDEOSTABLE)) {
+ mdelay(2);
+ continue;
+ }
+
+ break;
+ }
+
+ /*
+ * If we couldn't stabilize, requeue and try again, because it means
+ * that the LVDS channel isn't stable yet.
+ */
+ ret = it6251_is_stable(it6251);
+ if (ret)
+ dev_err(&it6251->client->dev, "bridge is not stable\n");
+
+ return ret;
+}
+
+static int it6251_power_down(struct it6251_bridge *it6251)
+{
+ struct device *dev = &it6251->client->dev;
+ int ret = 0;
+
+ if (regulator_is_enabled(it6251->regulator)) {
+ ret = regulator_disable(it6251->regulator);
+ if (ret)
+ dev_err(dev, "unable to disable regulator\n");
+ }
+
+ return ret;
+}
+
+static int it6251_power_up(struct it6251_bridge *it6251)
+{
+ struct i2c_client *client = it6251->client;
+ u8 regs[4];
+ int i, ret;
+
+ ret = regulator_enable(it6251->regulator);
+ if (ret) {
+ dev_err(&client->dev, "unable to enable regulator\n");
+ return ret;
+ }
+
+ /* Sometimes it seems like multiple tries are needed */
+ for (i = 0; i < 5; i++) {
+ ret = regmap_bulk_read(it6251->regmap, IT6251_VENDOR_ID_LOW,
+ regs, 4);
+ if (!ret && regs[0] && regs[1] && regs[2] && regs[3]) {
+ dev_info(&client->dev, "found ITE6251 [%04x:%04x]\n",
+ (regs[1] << 8) | regs[0],
+ (regs[3] << 8) | regs[2]);
+ return 0;
+ }
+
+ usleep_range(100000, 200000);
+ }
+
+ dev_err(&client->dev, "unable to read product id\n");
+ it6251_power_down(it6251);
+ return -EINVAL;
+}
+
+/* I2C driver functions */
+static void it6251_pre_enable(struct drm_bridge *bridge)
+{
+ struct it6251_bridge *it6251 = bridge_to_it6251(bridge);
+
+ if (drm_panel_prepare(it6251->panel)) {
+ DRM_ERROR("failed to prepare panel\n");
+ return;
+ }
+
+ it6251_power_up(it6251);
+}
+
+static void it6251_enable(struct drm_bridge *bridge)
+{
+ struct it6251_bridge *it6251 = bridge_to_it6251(bridge);
+ int tries, ret;
+
+ if (drm_panel_enable(it6251->panel)) {
+ DRM_ERROR("failed to enable panel\n");
+ return;
+ }
+
+ for (tries = 0; tries < 5; tries++) {
+ ret = it6251_init(it6251);
+ if (!ret)
+ return;
+
+ /* If the init failed, restart the chip */
+ it6251_power_down(it6251);
+ it6251_power_up(it6251);
+ }
+}
+
+static void it6251_disable(struct drm_bridge *bridge)
+{
+ struct it6251_bridge *it6251 = bridge_to_it6251(bridge);
+
+ if (drm_panel_disable(it6251->panel))
+ DRM_ERROR("failed to disable panel\n");
+}
+
+static void it6251_post_disable(struct drm_bridge *bridge)
+{
+ struct it6251_bridge *it6251 = bridge_to_it6251(bridge);
+
+ if (drm_panel_unprepare(it6251->panel))
+ DRM_ERROR("failed to unprepare panel\n");
+
+ it6251_power_down(it6251);
+}
+
+static int it6251_get_modes(struct drm_connector *connector)
+{
+ struct it6251_bridge *it6251 = conn_to_it6251(connector);
+
+ return drm_panel_get_modes(it6251->panel, connector);
+}
+
+static const struct drm_connector_helper_funcs it6251_connector_helper_funcs = {
+ .get_modes = it6251_get_modes,
+};
+
+static const struct drm_connector_funcs it6251_connector_funcs = {
+ .fill_modes = drm_helper_probe_single_connector_modes,
+ .destroy = drm_connector_cleanup,
+ .reset = drm_atomic_helper_connector_reset,
+ .atomic_duplicate_state = drm_atomic_helper_connector_duplicate_state,
+ .atomic_destroy_state = drm_atomic_helper_connector_destroy_state,
+};
+
+static int it6251_attach(struct drm_bridge *bridge, enum drm_bridge_attach_flags flags)
+{
+ struct it6251_bridge *it6251 = bridge_to_it6251(bridge);
+ int ret;
+
+ if (!bridge->encoder) {
+ DRM_ERROR("Parent encoder object not found");
+ return -ENODEV;
+ }
+
+ it6251->connector.polled = DRM_CONNECTOR_POLL_HPD;
+ ret = drm_connector_init(bridge->dev, &it6251->connector,
+ &it6251_connector_funcs,
+ DRM_MODE_CONNECTOR_eDP);
+ if (ret) {
+ DRM_ERROR("Failed to initialize connector with drm\n");
+ return ret;
+ }
+
+ drm_atomic_helper_connector_reset(&it6251->connector);
+ drm_connector_helper_add(&it6251->connector,
+ &it6251_connector_helper_funcs);
+ drm_connector_attach_encoder(&it6251->connector, bridge->encoder);
+
+ if (it6251->panel)
+ drm_panel_attach(it6251->panel, &it6251->connector);
+
+ drm_helper_hpd_irq_event(it6251->connector.dev);
+
+ return 0;
+}
+
+static const struct drm_bridge_funcs it6251_bridge_funcs = {
+ .pre_enable = it6251_pre_enable,
+ .enable = it6251_enable,
+ .disable = it6251_disable,
+ .post_disable = it6251_post_disable,
+ .attach = it6251_attach,
+};
+
+static const struct regmap_config it6251_regmap_config = {
+ .reg_bits = 8,
+ .val_bits = 8,
+ .max_register = 0xff,
+ .cache_type = REGCACHE_NONE,
+};
+
+static int
+it6251_probe(struct i2c_client *client, const struct i2c_device_id *id)
+{
+ struct device *dev = &client->dev;
+ struct it6251_bridge *it6251;
+ struct device_node *endpoint, *panel_node;
+ int ret;
+
+ it6251 = devm_kzalloc(dev, sizeof(*it6251), GFP_KERNEL);
+ if (!it6251)
+ return -ENOMEM;
+
+ endpoint = of_graph_get_next_endpoint(dev->of_node, NULL);
+ if (endpoint) {
+ panel_node = of_graph_get_remote_port_parent(endpoint);
+ if (panel_node) {
+ it6251->panel = of_drm_find_panel(panel_node);
+ of_node_put(panel_node);
+ if (!it6251->panel)
+ return -EPROBE_DEFER;
+ }
+ }
+
+ it6251->client = client;
+
+ it6251->regmap = devm_regmap_init_i2c(client, &it6251_regmap_config);
+ if (IS_ERR(it6251->regmap)) {
+ dev_err(dev, "cannot init i2c regmap for IT6251\n");
+ return PTR_ERR(it6251->regmap);
+ }
+
+ it6251->regulator = devm_regulator_get(dev, "power");
+ if (IS_ERR(it6251->regulator)) {
+ dev_err(dev, "no power regulator found for IT6251\n");
+ return PTR_ERR(it6251->regulator);
+ }
+
+ /* The LVDS-half of the chip shows up at address 0x5e */
+ it6251->lvds_client = i2c_new_ancillary_device(client, "lvds", 0x5e);
+ if (IS_ERR(it6251->lvds_client)) {
+ dev_err(dev, "cannot create I2C device for IT6251 LVDS\n");
+ return PTR_ERR(it6251->lvds_client);
+ }
+
+ it6251->lvds_regmap = regmap_init_i2c(it6251->lvds_client,
+ &it6251_regmap_config);
+ if (IS_ERR(it6251->lvds_regmap)) {
+ dev_err(dev, "cannot init i2c regmap for IT6251 LVDS\n");
+ ret = PTR_ERR(it6251->lvds_regmap);
+ goto err_lvds_regmap;
+ }
+
+ i2c_set_clientdata(client, it6251);
+
+ it6251->bridge.funcs = &it6251_bridge_funcs;
+ it6251->bridge.of_node = dev->of_node;
+ drm_bridge_add(&it6251->bridge);
+
+ return 0;
+
+err_lvds_regmap:
+ i2c_unregister_device(it6251->lvds_client);
+ return ret;
+}
+
+static int it6251_remove(struct i2c_client *client)
+{
+ struct it6251_bridge *it6251 = i2c_get_clientdata(client);
+ int ret;
+
+ ret = it6251_power_down(it6251);
+ if (ret)
+ return ret;
+
+ regmap_exit(it6251->lvds_regmap);
+ i2c_unregister_device(it6251->lvds_client);
+
+ return 0;
+}
+
+static int it6251_pm_suspend(struct device *dev)
+{
+ struct i2c_client *client = to_i2c_client(dev);
+ struct it6251_bridge *it6251 = i2c_get_clientdata(client);
+
+ return it6251_power_down(it6251);
+}
+
+static int it6251_pm_resume(struct device *dev)
+{
+ struct i2c_client *client = to_i2c_client(dev);
+ struct it6251_bridge *it6251 = i2c_get_clientdata(client);
+
+ return it6251_power_up(it6251);
+}
+
+static const struct dev_pm_ops it6251_dev_pm_ops = {
+ .suspend = it6251_pm_suspend,
+ .resume = it6251_pm_resume,
+ .restore = it6251_pm_resume,
+};
+
+static struct i2c_device_id it6251_ids[] = {
+ { "it6251", 0 },
+ { }
+};
+MODULE_DEVICE_TABLE(i2c, it6251_ids);
+
+static const struct of_device_id it6251_of_match[] = {
+ { .compatible = "ite,it6251", },
+ { }
+};
+MODULE_DEVICE_TABLE(of, it6251_of_match);
+
+static struct i2c_driver it6251_driver = {
+ .driver = {
+ .name = "it6251",
+ .pm = &it6251_dev_pm_ops,
+ .of_match_table = it6251_of_match,
+ },
+ .probe = it6251_probe,
+ .remove = it6251_remove,
+ .id_table = it6251_ids,
+};
+
+module_i2c_driver(it6251_driver);
+
+/* Module initialization */
+MODULE_AUTHOR("Sean Cross <xobs@xxxxxxxxxx>");
+MODULE_AUTHOR("Marek Vasut <marex@xxxxxxx>");
+MODULE_DESCRIPTION("ITE Tech 6251 LVDS to DisplayPort encoder");
+MODULE_LICENSE("GPL");
--
2.25.1
_______________________________________________
dri-devel mailing list
dri-devel@xxxxxxxxxxxxxxxxxxxxx
https://lists.freedesktop.org/mailman/listinfo/dri-devel
