On Tue, Oct 22, 2019 at 04:52:11PM +0200, Thierry Reding wrote:
> From: Thierry Reding <treding@xxxxxxxxxx>
>
> During the discussion of patches that enhance the drm_dp_link helpers it
> was concluded that these helpers aren't very useful to begin with. Start
> pushing the equivalent code into individual drivers to ultimately remove
> them.
>
> v4: use bulk DPCD writes if possible (Daniel Vetter)
>
> Signed-off-by: Thierry Reding <treding@xxxxxxxxxx>
Reviewed-by: Daniel Vetter <daniel.vetter@xxxxxxxx>
> ---
> drivers/gpu/drm/bridge/analogix-anx78xx.c | 56 ++++++++++++++++-------
> 1 file changed, 39 insertions(+), 17 deletions(-)
>
> diff --git a/drivers/gpu/drm/bridge/analogix-anx78xx.c b/drivers/gpu/drm/bridge/analogix-anx78xx.c
> index 9ddc1f3cf841..274989f96a91 100644
> --- a/drivers/gpu/drm/bridge/analogix-anx78xx.c
> +++ b/drivers/gpu/drm/bridge/analogix-anx78xx.c
> @@ -71,7 +71,6 @@ struct anx78xx {
> struct i2c_client *client;
> struct edid *edid;
> struct drm_connector connector;
> - struct drm_dp_link link;
> struct anx78xx_platform_data pdata;
> struct mutex lock;
>
> @@ -748,7 +747,7 @@ static int anx78xx_init_pdata(struct anx78xx *anx78xx)
>
> static int anx78xx_dp_link_training(struct anx78xx *anx78xx)
> {
> - u8 dp_bw, value;
> + u8 dp_bw, dpcd[2];
> int err;
>
> err = regmap_write(anx78xx->map[I2C_IDX_RX_P0], SP_HDMI_MUTE_CTRL_REG,
> @@ -801,18 +800,34 @@ static int anx78xx_dp_link_training(struct anx78xx *anx78xx)
> if (err)
> return err;
>
> - /* Check link capabilities */
> - err = drm_dp_link_probe(&anx78xx->aux, &anx78xx->link);
> - if (err < 0) {
> - DRM_ERROR("Failed to probe link capabilities: %d\n", err);
> - return err;
> - }
> + /*
> + * Power up the sink (DP_SET_POWER register is only available on DPCD
> + * v1.1 and later).
> + */
> + if (anx78xx->dpcd[DP_DPCD_REV] >= 0x11) {
> + err = drm_dp_dpcd_readb(&anx78xx->aux, DP_SET_POWER, &dpcd[0]);
> + if (err < 0) {
> + DRM_ERROR("Failed to read DP_SET_POWER register: %d\n",
> + err);
> + return err;
> + }
>
> - /* Power up the sink */
> - err = drm_dp_link_power_up(&anx78xx->aux, &anx78xx->link);
> - if (err < 0) {
> - DRM_ERROR("Failed to power up DisplayPort link: %d\n", err);
> - return err;
> + dpcd[0] &= ~DP_SET_POWER_MASK;
> + dpcd[0] |= DP_SET_POWER_D0;
> +
> + err = drm_dp_dpcd_writeb(&anx78xx->aux, DP_SET_POWER, dpcd[0]);
> + if (err < 0) {
> + DRM_ERROR("Failed to power up DisplayPort link: %d\n",
> + err);
> + return err;
> + }
> +
> + /*
> + * According to the DP 1.1 specification, a "Sink Device must
> + * exit the power saving state within 1 ms" (Section 2.5.3.1,
> + * Table 5-52, "Sink Control Field" (register 0x600).
> + */
> + usleep_range(1000, 2000);
> }
>
> /* Possibly enable downspread on the sink */
> @@ -851,15 +866,22 @@ static int anx78xx_dp_link_training(struct anx78xx *anx78xx)
> if (err)
> return err;
>
> - value = drm_dp_link_rate_to_bw_code(anx78xx->link.rate);
> + dpcd[0] = drm_dp_max_link_rate(anx78xx->dpcd);
> + dpcd[0] = drm_dp_link_rate_to_bw_code(dpcd[0]);
> err = regmap_write(anx78xx->map[I2C_IDX_TX_P0],
> - SP_DP_MAIN_LINK_BW_SET_REG, value);
> + SP_DP_MAIN_LINK_BW_SET_REG, dpcd[0]);
> if (err)
> return err;
>
> - err = drm_dp_link_configure(&anx78xx->aux, &anx78xx->link);
> + dpcd[1] = drm_dp_max_lane_count(anx78xx->dpcd);
> +
> + if (drm_dp_enhanced_frame_cap(anx78xx->dpcd))
> + dpcd[1] |= DP_LANE_COUNT_ENHANCED_FRAME_EN;
> +
> + err = drm_dp_dpcd_write(&anx78xx->aux, DP_LINK_BW_SET, dpcd,
> + sizeof(dpcd));
> if (err < 0) {
> - DRM_ERROR("Failed to configure DisplayPort link: %d\n", err);
> + DRM_ERROR("Failed to configure link: %d\n", err);
> return err;
> }
>
> --
> 2.23.0
>
--
Daniel Vetter
Software Engineer, Intel Corporation
http://blog.ffwll.ch
_______________________________________________
dri-devel mailing list
dri-devel@xxxxxxxxxxxxxxxxxxxxx
https://lists.freedesktop.org/mailman/listinfo/dri-devel
