Convert Samsung Exynos SROM controller bindings to DT schema format
using json-schema.
Signed-off-by: Krzysztof Kozlowski <krzk@xxxxxxxxxx>
---
Changes since v1:
1. Indent example with four spaces (more readable),
2. Split examples into two,
3. Fix pattern for subnode name,
4. Remove checks for #address-cells-ranges-#size-cells,
5. Add "additionalProperties" so the wrongly named subnodes would be
matched.
---
.../memory-controllers/exynos-srom.txt | 79 -----------
.../memory-controllers/exynos-srom.yaml | 128 ++++++++++++++++++
2 files changed, 128 insertions(+), 79 deletions(-)
delete mode 100644 Documentation/devicetree/bindings/memory-controllers/exynos-srom.txt
create mode 100644 Documentation/devicetree/bindings/memory-controllers/exynos-srom.yaml
diff --git a/Documentation/devicetree/bindings/memory-controllers/exynos-srom.txt b/Documentation/devicetree/bindings/memory-controllers/exynos-srom.txt
deleted file mode 100644
index f633b5d0f8ca..000000000000
--- a/Documentation/devicetree/bindings/memory-controllers/exynos-srom.txt
+++ /dev/null
@@ -1,79 +0,0 @@
-SAMSUNG Exynos SoCs SROM Controller driver.
-
-Required properties:
-- compatible : Should contain "samsung,exynos4210-srom".
-
-- reg: offset and length of the register set
-
-Optional properties:
-The SROM controller can be used to attach external peripherals. In this case
-extra properties, describing the bus behind it, should be specified as below:
-
-- #address-cells: Must be set to 2 to allow device address translation.
- Address is specified as (bank#, offset).
-
-- #size-cells: Must be set to 1 to allow device size passing
-
-- ranges: Must be set up to reflect the memory layout with four integer values
- per bank:
- <bank-number> 0 <parent address of bank> <size>
-
-Sub-nodes:
-The actual device nodes should be added as subnodes to the SROMc node. These
-subnodes, in addition to regular device specification, should contain the following
-properties, describing configuration of the relevant SROM bank:
-
-Required properties:
-- reg: bank number, base address (relative to start of the bank) and size of
- the memory mapped for the device. Note that base address will be
- typically 0 as this is the start of the bank.
-
-- samsung,srom-timing : array of 6 integers, specifying bank timings in the
- following order: Tacp, Tcah, Tcoh, Tacc, Tcos, Tacs.
- Each value is specified in cycles and has the following
- meaning and valid range:
- Tacp : Page mode access cycle at Page mode (0 - 15)
- Tcah : Address holding time after CSn (0 - 15)
- Tcoh : Chip selection hold on OEn (0 - 15)
- Tacc : Access cycle (0 - 31, the actual time is N + 1)
- Tcos : Chip selection set-up before OEn (0 - 15)
- Tacs : Address set-up before CSn (0 - 15)
-
-Optional properties:
-- reg-io-width : data width in bytes (1 or 2). If omitted, default of 1 is used.
-
-- samsung,srom-page-mode : if page mode is set, 4 data page mode will be configured,
- else normal (1 data) page mode will be set.
-
-Example: basic definition, no banks are configured
- memory-controller@12570000 {
- compatible = "samsung,exynos4210-srom";
- reg = <0x12570000 0x14>;
- };
-
-Example: SROMc with SMSC911x ethernet chip on bank 3
- memory-controller@12570000 {
- #address-cells = <2>;
- #size-cells = <1>;
- ranges = <0 0 0x04000000 0x20000 // Bank0
- 1 0 0x05000000 0x20000 // Bank1
- 2 0 0x06000000 0x20000 // Bank2
- 3 0 0x07000000 0x20000>; // Bank3
-
- compatible = "samsung,exynos4210-srom";
- reg = <0x12570000 0x14>;
-
- ethernet@3,0 {
- compatible = "smsc,lan9115";
- reg = <3 0 0x10000>; // Bank 3, offset = 0
- phy-mode = "mii";
- interrupt-parent = <&gpx0>;
- interrupts = <5 8>;
- reg-io-width = <2>;
- smsc,irq-push-pull;
- smsc,force-internal-phy;
-
- samsung,srom-page-mode;
- samsung,srom-timing = <9 12 1 9 1 1>;
- };
- };
diff --git a/Documentation/devicetree/bindings/memory-controllers/exynos-srom.yaml b/Documentation/devicetree/bindings/memory-controllers/exynos-srom.yaml
new file mode 100644
index 000000000000..cdfe3f7f0ea9
--- /dev/null
+++ b/Documentation/devicetree/bindings/memory-controllers/exynos-srom.yaml
@@ -0,0 +1,128 @@
+# SPDX-License-Identifier: GPL-2.0
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/memory-controllers/exynos-srom.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Samsung Exynos SoC SROM Controller driver
+
+maintainers:
+ - Krzysztof Kozlowski <krzk@xxxxxxxxxx>
+
+description: |+
+ The SROM controller can be used to attach external peripherals. In this case
+ extra properties, describing the bus behind it, should be specified.
+
+properties:
+ compatible:
+ items:
+ - const: samsung,exynos4210-srom
+
+ reg:
+ maxItems: 1
+
+ "#address-cells":
+ const: 2
+
+ "#size-cells":
+ const: 1
+
+ ranges:
+ description: |
+ Reflects the memory layout with four integer values per bank. Format:
+ <bank-number> 0 <parent address of bank> <size>
+ Up to four banks are supported.
+
+patternProperties:
+ "^.*@[0-3],[a-f0-9]+$":
+ type: object
+ description:
+ The actual device nodes should be added as subnodes to the SROMc node.
+ These subnodes, in addition to regular device specification, should
+ contain the following properties, describing configuration
+ of the relevant SROM bank.
+
+ properties:
+ reg:
+ description:
+ Bank number, base address (relative to start of the bank) and size
+ of the memory mapped for the device. Note that base address will be
+ typically 0 as this is the start of the bank.
+ maxItems: 1
+
+ reg-io-width:
+ allOf:
+ - $ref: /schemas/types.yaml#/definitions/uint32
+ - enum: [1, 2]
+ description:
+ Data width in bytes (1 or 2). If omitted, default of 1 is used.
+
+ samsung,srom-page-mode:
+ description:
+ If page mode is set, 4 data page mode will be configured,
+ else normal (1 data) page mode will be set.
+ type: boolean
+
+ samsung,srom-timing:
+ allOf:
+ - $ref: /schemas/types.yaml#/definitions/uint32-array
+ - items:
+ minItems: 6
+ maxItems: 6
+ description: |
+ Array of 6 integers, specifying bank timings in the following order:
+ Tacp, Tcah, Tcoh, Tacc, Tcos, Tacs.
+ Each value is specified in cycles and has the following meaning
+ and valid range:
+ Tacp: Page mode access cycle at Page mode (0 - 15)
+ Tcah: Address holding time after CSn (0 - 15)
+ Tcoh: Chip selection hold on OEn (0 - 15)
+ Tacc: Access cycle (0 - 31, the actual time is N + 1)
+ Tcos: Chip selection set-up before OEn (0 - 15)
+ Tacs: Address set-up before CSn (0 - 15)
+
+ required:
+ - reg
+ - samsung,srom-timing
+
+required:
+ - compatible
+ - reg
+
+additionalProperties: false
+
+examples:
+ - |
+ // Example: basic definition, no banks are configured
+ memory-controller@12560000 {
+ compatible = "samsung,exynos4210-srom";
+ reg = <0x12560000 0x14>;
+ };
+
+ - |
+ // Example: SROMc with SMSC911x ethernet chip on bank 3
+ memory-controller@12570000 {
+ #address-cells = <2>;
+ #size-cells = <1>;
+ ranges = <0 0 0x04000000 0x20000 // Bank0
+ 1 0 0x05000000 0x20000 // Bank1
+ 2 0 0x06000000 0x20000 // Bank2
+ 3 0 0x07000000 0x20000>; // Bank3
+
+ compatible = "samsung,exynos4210-srom";
+ reg = <0x12570000 0x14>;
+
+ ethernet@3,0 {
+ compatible = "smsc,lan9115";
+ reg = <3 0 0x10000>; // Bank 3, offset = 0
+ phy-mode = "mii";
+ interrupt-parent = <&gpx0>;
+ interrupts = <5 8>;
+ reg-io-width = <2>;
+ smsc,irq-push-pull;
+ smsc,force-internal-phy;
+
+ samsung,srom-page-mode;
+ samsung,srom-timing = <9 12 1 9 1 1>;
+ };
+ };
--
2.17.1
_______________________________________________
dri-devel mailing list
dri-devel@xxxxxxxxxxxxxxxxxxxxx
https://lists.freedesktop.org/mailman/listinfo/dri-devel
