On Tue, May 21, 2019 at 02:15:19PM +0200, Ondřej Jirman wrote:
> Hi Maxime,
>
> On Tue, May 21, 2019 at 01:46:11PM +0200, Maxime Ripard wrote:
> > Hi,
> >
> > On Tue, May 21, 2019 at 01:50:08AM +0200, megous@xxxxxxxxxx wrote:
> > > From: Ondrej Jirman <megous@xxxxxxxxxx>
> > >
> > > Orange Pi 3 board requires enabling a voltage shifting circuit via GPIO
> > > for the DDC bus to be usable.
> > >
> > > Add support for hdmi-connector node's optional ddc-en-gpios property to
> > > support this use case.
> > >
> > > Signed-off-by: Ondrej Jirman <megous@xxxxxxxxxx>
> > > ---
> > > drivers/gpu/drm/sun4i/sun8i_dw_hdmi.c | 55 +++++++++++++++++++++++++--
> > > drivers/gpu/drm/sun4i/sun8i_dw_hdmi.h | 3 ++
> > > 2 files changed, 55 insertions(+), 3 deletions(-)
> > >
> > > diff --git a/drivers/gpu/drm/sun4i/sun8i_dw_hdmi.c b/drivers/gpu/drm/sun4i/sun8i_dw_hdmi.c
> > > index 39d8509d96a0..59b81ba02d96 100644
> > > --- a/drivers/gpu/drm/sun4i/sun8i_dw_hdmi.c
> > > +++ b/drivers/gpu/drm/sun4i/sun8i_dw_hdmi.c
> > > @@ -98,6 +98,30 @@ static u32 sun8i_dw_hdmi_find_possible_crtcs(struct drm_device *drm,
> > > return crtcs;
> > > }
> > >
> > > +static int sun8i_dw_hdmi_find_connector_pdev(struct device *dev,
> > > + struct platform_device **pdev_out)
> > > +{
> > > + struct platform_device *pdev;
> > > + struct device_node *remote;
> > > +
> > > + remote = of_graph_get_remote_node(dev->of_node, 1, -1);
> > > + if (!remote)
> > > + return -ENODEV;
> > > +
> > > + if (!of_device_is_compatible(remote, "hdmi-connector")) {
> > > + of_node_put(remote);
> > > + return -ENODEV;
> > > + }
> > > +
> > > + pdev = of_find_device_by_node(remote);
> > > + of_node_put(remote);
> > > + if (!pdev)
> > > + return -ENODEV;
> > > +
> > > + *pdev_out = pdev;
> > > + return 0;
> > > +}
> > > +
> > > static int sun8i_dw_hdmi_bind(struct device *dev, struct device *master,
> > > void *data)
> > > {
> > > @@ -151,16 +175,29 @@ static int sun8i_dw_hdmi_bind(struct device *dev, struct device *master,
> > > return PTR_ERR(hdmi->regulator);
> > > }
> > >
> > > + ret = sun8i_dw_hdmi_find_connector_pdev(dev, &hdmi->connector_pdev);
> > > + if (!ret) {
> > > + hdmi->ddc_en = gpiod_get_optional(&hdmi->connector_pdev->dev,
> > > + "ddc-en", GPIOD_OUT_HIGH);
> > > + if (IS_ERR(hdmi->ddc_en)) {
> > > + platform_device_put(hdmi->connector_pdev);
> > > + dev_err(dev, "Couldn't get ddc-en gpio\n");
> > > + return PTR_ERR(hdmi->ddc_en);
> > > + }
> > > + }
> > > +
> > > ret = regulator_enable(hdmi->regulator);
> > > if (ret) {
> > > dev_err(dev, "Failed to enable regulator\n");
> > > - return ret;
> > > + goto err_unref_ddc_en;
> > > }
> > >
> > > + gpiod_set_value(hdmi->ddc_en, 1);
> > > +
> >
> > Do you really need this to be done all the time? I'm guessing you
> > would only need this when running .get_modes, right?
>
> I don't think it hurts anything. Enabled voltage shifting circuit doesn't
> draw any current, unless DDC is actually transmitting data. On most boards
> I'd imagine this circuit is always on anyway (Orange Pi 3 schematic even has
> an option to tie this signal to VCC-IO instead of GPIO).
Ok, it works for me then
Maxime
--
Maxime Ripard, Bootlin
Embedded Linux and Kernel engineering
https://bootlin.com
Attachment:
signature.asc
Description: PGP signature
_______________________________________________ dri-devel mailing list dri-devel@xxxxxxxxxxxxxxxxxxxxx https://lists.freedesktop.org/mailman/listinfo/dri-devel
