On Tue, May 14, 2019 at 10:18 AM Ser, Simon <simon.ser@xxxxxxxxx> wrote: > > On Tue, 2019-05-14 at 11:02 +0300, Pekka Paalanen wrote: > > On Mon, 13 May 2019 11:34:58 +0200 > > Daniel Vetter <daniel.vetter@xxxxxxxx> wrote: > > > > > On Mon, May 13, 2019 at 11:02 AM Paul Kocialkowski > > > <paul.kocialkowski@xxxxxxxxxxx> wrote: > > > > Hi, > > > > > > > > On Fri, 2019-05-10 at 16:54 +0200, Daniel Vetter wrote: > > > > > On Fri, May 10, 2019 at 2:12 PM Paul Kocialkowski > > > > > <paul.kocialkowski@xxxxxxxxxxx> wrote: > > > > > > Hi, > > > > > > > > > > > > On Tue, 2019-05-07 at 21:57 +0530, Ramalingam C wrote: > > > > > > > DRM API for generating uevent for a status changes of connector's > > > > > > > property. > > > > > > > > > > > > > > This uevent will have following details related to the status change: > > > > > > > > > > > > > > HOTPLUG=1, CONNECTOR=<connector_id> and PROPERTY=<property_id> > > > > > > > > > > > > > > Need ACK from this uevent from userspace consumer. > > > > > > > > > > > > So we just had some discussions over on IRC and at about the hotplug > > > > > > issue and came up with similar ideas: > > > > > > https://lists.freedesktop.org/archives/dri-devel/2019-May/217408.html > > > > > > > > > > > > The conclusions of these discussions so far would be to have a more or > > > > > > less fine grain of uevent reporting depending on what happened. The > > > > > > point is that we need to cover different cases: > > > > > > - one or more properties changed; > > > > > > - the connector status changed; > > > > > > - something else about the connector changed (e.g. EDID/modes) > > > > > > > > > > > > For the first case, we can send out: > > > > > > HOTPLUG=1 > > > > > > CONNECTOR=<id> > > > > > > PROPERTY=<id> > > > > > > > > > > > > and no reprobe is required. > > > > > > > > > > > > For the second one, something like: > > > > > > HOTPLUG=1 > > > > > > CONNECTOR=<id> > > > > > > STATUS=Connected/Disconnected > > > > > > > > > > > > and a connector probe is needed for connected, but not for > > > > > > disconnected; > > > > > > > > > > > > For the third one, we can only indicate the connector: > > > > > > HOTPLUG=1 > > > > > > CONNECTOR=<id> > > > > > > > > > > > > and a reprobe of the connector is always needed > > > > > > > > > > There's no material difference between this one and the previous one. > > > > > Plus there's no beenfit in supplying the actual value of the property, > > > > > i.e. we can reuse the same PROPERTY=<id-of-status-property> trick. > > > > > > > > That's the idea, but we need to handle status changes differently than > > > > properties, since as far as I know, connected/unconnected status is not > > > > exposed as a prop for the connector. > > > > > > Oops, totally missed that. "Everything is a property" is kinda > > > new-ish, at least compared to kms. Kinda tempted to just make status > > > into a property. Or another excuse why we should expose the epoch > > > property :-) > > > > Hi Daniel, > > > > just to clarify the first case, specific to one very particular > > property: > > > > With HDCP, there is a property that may change dynamically at runtime > > (the undesired/desired/enabled tristate). Userspace must be notified > > when it changes, I do not want userspace have to poll that property > > with a timer. > > > > When that property alone changes, and userspace is prepared to handle > > that property changing alone, it must not trigger a reprobe of the > > connector. There is no reason to reprobe at that point AFAIU. > > > > How do you ensure that userspace can avoid triggering a reprobe with the > > epoch approach or with any alternate uevent design? > > > > We need an event to userspace that indicates that re-reading the > > properties is enough and reprobe of the connector is not necessary. > > This is complementary to indicating to userspace that only some > > connectors need to be reprobed instead of everything. > > Can't you use the PROPERTY hint? If PROPERTY is the HDCP one, skip the > reprobing. Would that work? Yes that's the idea, depending upon which property you get you know it's a sink change (needs full reprobe) or something else like hdcp state machinery update. Wrt avoiding the full reprobe for sink changes: I think we should indeed decouple that from the per-connector event for sink changes. That along is a good win already, since you know for which connector you need to call drmGetConnector (which forces the reprobe). It would be nice to only call drmGetConnectorCurrent (avoids the reprobe), but historically speaking every time we tried to rely on this we ended up regretting things. -Daniel -- Daniel Vetter Software Engineer, Intel Corporation +41 (0) 79 365 57 48 - http://blog.ffwll.ch _______________________________________________ dri-devel mailing list dri-devel@xxxxxxxxxxxxxxxxxxxxx https://lists.freedesktop.org/mailman/listinfo/dri-devel
