Hi Laurent,
On 06/03/2019 23:23, Laurent Pinchart wrote:
> From: Stefan Agner <stefan@xxxxxxxx>
>
> The DRM bus flags convey additional information on pixel data on
> the bus. All current available bus flags might be of interest for
> a bridge. Remove the sampling_edge field and use bus_flags.
>
> In the case at hand a dumb VGA bridge needs a specific data enable
> polarity (DRM_BUS_FLAG_DE_LOW).
>
> Signed-off-by: Stefan Agner <stefan@xxxxxxxx>
> Signed-off-by: Laurent Pinchart <laurent.pinchart@xxxxxxxxxxxxxxxx>
Trivial but, should you have a +renesas ^ there?
> Reviewed-by: Tomi Valkeinen <tomi.valkeinen@xxxxxx>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@xxxxxxxxxxxxxxxx>
> ---
> drivers/gpu/drm/bridge/dumb-vga-dac.c | 6 +++---
> include/drm/drm_bridge.h | 12 +++++-------
> 2 files changed, 8 insertions(+), 10 deletions(-)
>
> diff --git a/drivers/gpu/drm/bridge/dumb-vga-dac.c b/drivers/gpu/drm/bridge/dumb-vga-dac.c
> index 94ed450e308d..e64736c39a9f 100644
> --- a/drivers/gpu/drm/bridge/dumb-vga-dac.c
> +++ b/drivers/gpu/drm/bridge/dumb-vga-dac.c
> @@ -234,7 +234,7 @@ static int dumb_vga_remove(struct platform_device *pdev)
> */
> static const struct drm_bridge_timings default_dac_timings = {
> /* Timing specifications, datasheet page 7 */
> - .sampling_edge = DRM_BUS_FLAG_PIXDATA_SAMPLE_POSEDGE,
> + .input_bus_flags = DRM_BUS_FLAG_PIXDATA_SAMPLE_POSEDGE,
> .setup_time_ps = 500,
> .hold_time_ps = 1500,
> };
> @@ -245,7 +245,7 @@ static const struct drm_bridge_timings default_dac_timings = {
> */
> static const struct drm_bridge_timings ti_ths8134_dac_timings = {
> /* From timing diagram, datasheet page 9 */
> - .sampling_edge = DRM_BUS_FLAG_PIXDATA_SAMPLE_POSEDGE,
> + .input_bus_flags = DRM_BUS_FLAG_PIXDATA_SAMPLE_POSEDGE,
> /* From datasheet, page 12 */
> .setup_time_ps = 3000,
> /* I guess this means latched input */
> @@ -258,7 +258,7 @@ static const struct drm_bridge_timings ti_ths8134_dac_timings = {
> */
> static const struct drm_bridge_timings ti_ths8135_dac_timings = {
> /* From timing diagram, datasheet page 14 */
> - .sampling_edge = DRM_BUS_FLAG_PIXDATA_SAMPLE_POSEDGE,
> + .input_bus_flags = DRM_BUS_FLAG_PIXDATA_SAMPLE_POSEDGE,
> /* From datasheet, page 16 */
> .setup_time_ps = 2000,
> .hold_time_ps = 500,
> diff --git a/include/drm/drm_bridge.h b/include/drm/drm_bridge.h
> index 5e5129206f40..d4428913a4e1 100644
> --- a/include/drm/drm_bridge.h
> +++ b/include/drm/drm_bridge.h
> @@ -244,15 +244,13 @@ struct drm_bridge_funcs {
> */
> struct drm_bridge_timings {
> /**
> - * @sampling_edge:
> + * @input_bus_flags:
> *
> - * Tells whether the bridge samples the digital input signals from the
> - * display engine on the positive or negative edge of the clock. This
> - * should use the DRM_BUS_FLAG_PIXDATA_SAMPLE_[POS|NEG]EDGE and
> - * DRM_BUS_FLAG_SYNC_SAMPLE_[POS|NEG]EDGE bitwise flags from the DRM
> - * connector (bit 2, 3, 6 and 7 valid).
> + * Tells what additional settings for the pixel data on the bus
> + * this bridge requires (like pixel signal polarity). See also
> + * &drm_display_info->bus_flags.
> */
> - u32 sampling_edge;
> + u32 input_bus_flags;
> /**
> * @setup_time_ps:
> *
>
--
Regards
--
Kieran
_______________________________________________
dri-devel mailing list
dri-devel@xxxxxxxxxxxxxxxxxxxxx
https://lists.freedesktop.org/mailman/listinfo/dri-devel
