From: Stefan Agner <stefan@xxxxxxxx>
The DRM bus flags convey additional information on pixel data on
the bus. All current available bus flags might be of interest for
a bridge. Remove the sampling_edge field and use bus_flags.
In the case at hand a dumb VGA bridge needs a specific data enable
polarity (DRM_BUS_FLAG_DE_LOW).
Signed-off-by: Stefan Agner <stefan@xxxxxxxx>
Signed-off-by: Laurent Pinchart <laurent.pinchart@xxxxxxxxxxxxxxxx>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@xxxxxx>
Tested-by: Sebastian Reichel <sebastian.reichel@xxxxxxxxxxxxx>
---
Changes since v1:
- Renamed bus_flags to input_bus_flags
---
drivers/gpu/drm/bridge/dumb-vga-dac.c | 6 +++---
include/drm/drm_bridge.h | 12 +++++-------
2 files changed, 8 insertions(+), 10 deletions(-)
diff --git a/drivers/gpu/drm/bridge/dumb-vga-dac.c b/drivers/gpu/drm/bridge/dumb-vga-dac.c
index 94ed450e308d..e64736c39a9f 100644
--- a/drivers/gpu/drm/bridge/dumb-vga-dac.c
+++ b/drivers/gpu/drm/bridge/dumb-vga-dac.c
@@ -234,7 +234,7 @@ static int dumb_vga_remove(struct platform_device *pdev)
*/
static const struct drm_bridge_timings default_dac_timings = {
/* Timing specifications, datasheet page 7 */
- .sampling_edge = DRM_BUS_FLAG_PIXDATA_SAMPLE_POSEDGE,
+ .input_bus_flags = DRM_BUS_FLAG_PIXDATA_SAMPLE_POSEDGE,
.setup_time_ps = 500,
.hold_time_ps = 1500,
};
@@ -245,7 +245,7 @@ static const struct drm_bridge_timings default_dac_timings = {
*/
static const struct drm_bridge_timings ti_ths8134_dac_timings = {
/* From timing diagram, datasheet page 9 */
- .sampling_edge = DRM_BUS_FLAG_PIXDATA_SAMPLE_POSEDGE,
+ .input_bus_flags = DRM_BUS_FLAG_PIXDATA_SAMPLE_POSEDGE,
/* From datasheet, page 12 */
.setup_time_ps = 3000,
/* I guess this means latched input */
@@ -258,7 +258,7 @@ static const struct drm_bridge_timings ti_ths8134_dac_timings = {
*/
static const struct drm_bridge_timings ti_ths8135_dac_timings = {
/* From timing diagram, datasheet page 14 */
- .sampling_edge = DRM_BUS_FLAG_PIXDATA_SAMPLE_POSEDGE,
+ .input_bus_flags = DRM_BUS_FLAG_PIXDATA_SAMPLE_POSEDGE,
/* From datasheet, page 16 */
.setup_time_ps = 2000,
.hold_time_ps = 500,
diff --git a/include/drm/drm_bridge.h b/include/drm/drm_bridge.h
index 5e5129206f40..d4428913a4e1 100644
--- a/include/drm/drm_bridge.h
+++ b/include/drm/drm_bridge.h
@@ -244,15 +244,13 @@ struct drm_bridge_funcs {
*/
struct drm_bridge_timings {
/**
- * @sampling_edge:
+ * @input_bus_flags:
*
- * Tells whether the bridge samples the digital input signals from the
- * display engine on the positive or negative edge of the clock. This
- * should use the DRM_BUS_FLAG_PIXDATA_SAMPLE_[POS|NEG]EDGE and
- * DRM_BUS_FLAG_SYNC_SAMPLE_[POS|NEG]EDGE bitwise flags from the DRM
- * connector (bit 2, 3, 6 and 7 valid).
+ * Tells what additional settings for the pixel data on the bus
+ * this bridge requires (like pixel signal polarity). See also
+ * &drm_display_info->bus_flags.
*/
- u32 sampling_edge;
+ u32 input_bus_flags;
/**
* @setup_time_ps:
*
--
Regards,
Laurent Pinchart
_______________________________________________
dri-devel mailing list
dri-devel@xxxxxxxxxxxxxxxxxxxxx
https://lists.freedesktop.org/mailman/listinfo/dri-devel
