On Thu, Jan 31, 2019 at 09:13:55AM +0100, Christoph Hellwig wrote: > On Wed, Jan 30, 2019 at 03:52:13PM -0700, Logan Gunthorpe wrote: > > > *shrug* so what if the special GUP called a VMA op instead of > > > traversing the VMA PTEs today? Why does it really matter? It could > > > easily change to a struct page flow tomorrow.. > > > > Well it's so that it's composable. We want the SGL->DMA side to work for > > APIs from kernel space and not have to run a completely different flow > > for kernel drivers than from userspace memory. > > Yes, I think that is the important point. > > All the other struct page discussion is not about anyone of us wanting > struct page - heck it is a pain to deal with, but then again it is > there for a reason. > > In the typical GUP flows we have three uses of a struct page: We do not want GUP. Yes some RDMA driver and other use GUP but they should only use GUP on regular vma not on special vma (ie mmap of a device file). Allowing GUP on those is insane. It is better to special case the peer to peer mapping because _it is_ special, nothing inside those are manage by core mm and driver can deal with them in weird way (GPU certainly do and for very good reasons without which they would perform badly). > > (1) to carry a physical address. This is mostly through > struct scatterlist and struct bio_vec. We could just store > a magic PFN-like value that encodes the physical address > and allow looking up a page if it exists, and we had at least > two attempts at it. In some way I think that would actually > make the interfaces cleaner, but Linus has NACKed it in the > past, so we'll have to convince him first that this is the > way forward Wasting 64bytes just to carry address is a waste for everyone. > (2) to keep a reference to the memory so that it doesn't go away > under us due to swapping, process exit, unmapping, etc. > No idea how we want to solve this, but I guess you have > some smart ideas? The DMA API has _never_ dealt with page refcount and it have always been up to the user of the DMA API to ascertain that it is safe for them to map/unmap page/resource they are providing to the DMA API. The lifetime management of page or resource provided to the DMA API should remain the problem of the caller and not be something the DMA API cares one bit about. > (3) to make the PTEs dirty after writing to them. Again no sure > what our preferred interface here would be Again the DMA API has never dealt with that nor should he. What does dirty pte means for a special mapping (mmap of device file) ? There is no single common definition for that, most driver do not care about it and it get fully ignore. > > If we solve all of the above problems I'd be more than happy to > go with a non-struct page based interface for BAR P2P. But we'll > have to solve these issues in a generic way first. None of the above are problems the DMA API need to solve. The DMA API is about mapping some memory resource to a device. For regular main memory it is easy on most architecture (anything with a sane IOMMU). For IO resources it is not as straight forward as it was often left undefined in the architecture platform documentation or the inter- connect standard. AFAIK mapping BAR from one PCIE device to another through IOMMU works well on recent Intel and AMD platform. We will probably need to use some whitelist at i am not sure this is something Intel or AMD guarantee, i believe they want to start guaranteeing it. So having one DMA API for regular memory and one for IO memory aka resource (dma_map_resource()) sounds like the only sane approach here. It is fundamentally different memory and we should not try to muddle the water by having it go through a single common API. There is no benefit to that beside saving couple hundred of lines of code to some driver and this couple hundred lines of code can be move to a common helpers. So to me it is lot sane to provide an helper that would deal with the different vma type on behalf of device than forcing down struct page. Something like: vma_dma_map_range(vma, device, start, end, flags, pa[]) vma_dma_unmap_range(vma, device, start, end, flags, pa[]) VMA_DMA_MAP_FLAG_WRITE VMA_DMA_MAP_FLAG_PIN Which would use GUP or special vma handling on behalf of the calling device or use a special p2p code path for special vma. Device that need pinning set the flag and it is up to the exporting device to accept or not. Pinning when using GUP is obvious. When the vma goes away the importing device must update its device page table to some dummy page or do something sane, because keeping things map after that point does not make sense anymore. Device is no longer operating on a range of virtual address that make sense. So instead of pushing p2p handling within GUP to not disrupt existing driver workflow. It is better to provide an helper that handle all the gory details for the device driver. It does not change things for the driver and allows proper special casing. Cheers, Jérôme _______________________________________________ dri-devel mailing list dri-devel@xxxxxxxxxxxxxxxxxxxxx https://lists.freedesktop.org/mailman/listinfo/dri-devel
