23.01.2019 17:04, Thierry Reding пишет:
> On Wed, Jan 23, 2019 at 04:41:44PM +0300, Dmitry Osipenko wrote:
>> 23.01.2019 12:39, Thierry Reding пишет:
>>> From: Thierry Reding <treding@xxxxxxxxxx>
>>>
>>> On Tegra186 and later, the ARM SMMU provides an input address space that
>>> is 48 bits wide. However, memory clients can only address up to 40 bits.
>>> If the geometry is used as-is, allocations of IOVA space can end up in a
>>> region that cannot be addressed by the memory clients.
>>>
>>> To fix this, restrict the IOVA space to the DMA mask of the host1x
>>> device. Note that, technically, the IOVA space needs to be restricted to
>>> the intersection of the DMA masks for all clients that are attached to
>>> the IOMMU domain. In practice using the DMA mask of the host1x device is
>>> sufficient because all host1x clients share the same DMA mask.
>>>
>>> Signed-off-by: Thierry Reding <treding@xxxxxxxxxx>
>>> ---
>>> drivers/gpu/drm/tegra/drm.c | 5 +++--
>>> 1 file changed, 3 insertions(+), 2 deletions(-)
>>>
>>> diff --git a/drivers/gpu/drm/tegra/drm.c b/drivers/gpu/drm/tegra/drm.c
>>> index 271c7a5fc954..0c5f1e6a0446 100644
>>> --- a/drivers/gpu/drm/tegra/drm.c
>>> +++ b/drivers/gpu/drm/tegra/drm.c
>>> @@ -136,11 +136,12 @@ static int tegra_drm_load(struct drm_device *drm, unsigned long flags)
>>>
>>> if (tegra->domain) {
>>> u64 carveout_start, carveout_end, gem_start, gem_end;
>>> + u64 dma_mask = dma_get_mask(&device->dev);
>>> dma_addr_t start, end;
>>> unsigned long order;
>>>
>>> - start = tegra->domain->geometry.aperture_start;
>>> - end = tegra->domain->geometry.aperture_end;
>>> + start = tegra->domain->geometry.aperture_start & dma_mask;
>>> + end = tegra->domain->geometry.aperture_end & dma_mask;
>>>
>>> gem_start = start;
>>> gem_end = end - CARVEOUT_SZ;
>>>
>>
>> Wow, so IOVA could address >32bits on later Tegra's. AFAIK, currently
>> there is no support for a proper programming of the 64bit addresses in
>> the drivers code, hence.. won't it make sense to force IOVA mask to
>> 32bit for now and hope that the second halve of address registers
>> happen to be 0x00000000 in HW?
>
> I think this restriction only applies to display at this point. In
> practice you'd be hard put to trigger that case because IOVA memory is
> allocated from the bottom, so you'd actually need to use up to 4 GiB of
> IOVA space before hitting that.
>
> That said, I vaguely remember typing up the patch to support writing the
> WINBUF_START_ADDR_HI register and friends, but it looks as if that was
> never merged.
>
> I'll try to dig out that patch (or rewrite it, shouldn't be very
> difficult) and make it part of this series. I'd rather fix that issue
> than arbitrarily restrict the IOVA space, because that's likely to come
> back and bite us at some point.
You could also try to change the IOVA allocation logic and see what will fail :)
_______________________________________________
dri-devel mailing list
dri-devel@xxxxxxxxxxxxxxxxxxxxx
https://lists.freedesktop.org/mailman/listinfo/dri-devel
