On 2018-12-03 16:57, Doug Anderson wrote:
Hi,
On Mon, Dec 3, 2018 at 2:27 PM Jeykumar Sankaran
<jsanka@xxxxxxxxxxxxxx>
wrote:
+ dsi0: dsi@ae94000 {
+ compatible = "qcom,mdss-dsi-ctrl";
+ reg = <0xae94000 0x400>;
+ reg-names = "dsi_ctrl";
+
+ interrupt-parent = <&mdss>;
+ interrupts = <4 IRQ_TYPE_LEVEL_HIGH>;
+
+ clocks = <&dispcc
DISP_CC_MDSS_BYTE0_CLK>,
+ <&dispcc
DISP_CC_MDSS_BYTE0_INTF_CLK>,
+ <&dispcc
DISP_CC_MDSS_PCLK0_CLK>,
+ <&dispcc
DISP_CC_MDSS_ESC0_CLK>,
+ <&dispcc
DISP_CC_MDSS_AHB_CLK>,
+ <&dispcc
DISP_CC_MDSS_AXI_CLK>;
+ clock-names = "byte",
+ "byte_intf",
+ "pixel",
+ "core",
+ "iface",
+ "bus";
+
+ phys = <&dsi0_phy>;
+ phy-names = "dsi0";
I'm pretty sure that this should just be "dsi" and the one below in
dsi1 should also be called "dsi". +Jordan should confirm.
Makes sense. I can fix that!
+ dsi1: dsi@ae96000 {
+ compatible = "qcom,mdss-dsi-ctrl";
+ reg = <0xae96000 0x400>;
+ reg-names = "dsi_ctrl";
+
+ interrupt-parent = <&mdss>;
+ interrupts = <5 IRQ_TYPE_LEVEL_HIGH>;
+
+ clocks = <&dispcc
DISP_CC_MDSS_BYTE1_CLK>,
+ <&dispcc
DISP_CC_MDSS_BYTE1_INTF_CLK>,
+ <&dispcc
DISP_CC_MDSS_PCLK1_CLK>,
+ <&dispcc
DISP_CC_MDSS_ESC1_CLK>,
+ <&dispcc
DISP_CC_MDSS_AHB_CLK>,
+ <&dispcc
DISP_CC_MDSS_AXI_CLK>;
+ clock-names = "byte",
+ "byte_intf",
+ "pixel",
+ "core",
+ "iface",
+ "bus";
+
+ phys = <&dsi1_phy>;
+ phy-names = "dsi1";
+
+ status = "disabled";
This "disabled" is causing me problems. I don't actually need "dsi1"
but if I don't enable "dsi1" then my display doesn't come up. :( I
ran out of time to debug but I wonder if this is this the standard
thing where DRM needs to wait for all the components to probe until it
can finish? If nobody on this list just knows I'll dig tomorrow and
confirm that my memory isn't faulty and see what we've done about this
in the past.
https://patchwork.kernel.org/patch/10467895/
Can you try out with this change (reviewed but not merged yet). It
validates
the nodes before adding to the DSI list.
One last note: it's pretty weird that you sent out only 1/3 and not
2/3 and 3/3. If you're not ready to send out MTP stuff yet then you
should send out v6 as just a singleton patch.
Yes. I was trying to separate this one out as an independent change.
Sandeep
is working on the comments on removing the pinctrl nodes and updated
mtp nodes. He should be posting 2/3 and 3/3 in the next couple of days.
Thanks,
Jeykumar S.
-Doug
--
Jeykumar S
_______________________________________________
dri-devel mailing list
dri-devel@xxxxxxxxxxxxxxxxxxxxx
https://lists.freedesktop.org/mailman/listinfo/dri-devel
