On Wed, 2012-02-29 at 12:49 +0800, chenhc@xxxxxxxxxx wrote:
> > On Tue, 2012-02-21 at 18:37 +0800, Chen Jie wrote:
> >> 在 2012年2月17日 下午5:27，Chen Jie <chenj@xxxxxxxxxx> 写道：
> >> >> One good way to test gart is to go over GPU gart table and write a
> >> >> dword using the GPU at end of each page something like 0xCAFEDEAD
> >> >> or somevalue that is unlikely to be already set. And then go over
> >> >> all the page and check that GPU write succeed. Abusing the scratch
> >> >> register write back feature is the easiest way to try that.
> >> > I'm planning to add a GART table check procedure when resume, which
> >> > will go over GPU gart table:
> >> > 1. read(backup) a dword at end of each GPU page
> >> > 2. write a mark by GPU and check it
> >> > 3. restore the original dword
> >> Attachment validateGART.patch do the job:
> >> * It current only works for mips64 platform.
> >> * To use it, apply all_in_vram.patch first, which will allocate CP
> >> ring, ih, ib in VRAM and hard code no_wb=1.
> >>
> >> The gart test routine will be invoked in r600_resume. We've tried it,
> >> and find that when lockup happened the gart table was good before
> >> userspace restarting. The related dmesg follows:
> >> [ 1521.820312] [drm] r600_gart_table_validate(): Validate GART Table
> >> at 9000000040040000, 32768 entries, Dummy
> >> Page[0x000000000e004000-0x000000000e007fff]
> >> [ 1522.019531] [drm] r600_gart_table_validate(): Sweep 32768
> >> entries(valid=8544, invalid=24224, total=32768).
> >> ...
> >> [ 1531.156250] PM: resume of devices complete after 9396.588 msecs
> >> [ 1532.152343] Restarting tasks ... done.
> >> [ 1544.468750] radeon 0000:01:05.0: GPU lockup CP stall for more than
> >> 10003msec
> >> [ 1544.472656] ------------[ cut here ]------------
> >> [ 1544.480468] WARNING: at drivers/gpu/drm/radeon/radeon_fence.c:243
> >> radeon_fence_wait+0x25c/0x314()
> >> [ 1544.488281] GPU lockup (waiting for 0x0002136B last fence id
> >> 0x0002136A)
> >> ...
> >> [ 1544.886718] radeon 0000:01:05.0: Wait for MC idle timedout !
> >> [ 1545.046875] radeon 0000:01:05.0: Wait for MC idle timedout !
> >> [ 1545.062500] radeon 0000:01:05.0: WB disabled
> >> [ 1545.097656] [drm] ring test succeeded in 0 usecs
> >> [ 1545.105468] [drm] ib test succeeded in 0 usecs
> >> [ 1545.109375] [drm] Enabling audio support
> >> [ 1545.113281] [drm] r600_gart_table_validate(): Validate GART Table
> >> at 9000000040040000, 32768 entries, Dummy
> >> Page[0x000000000e004000-0x000000000e007fff]
> >> [ 1545.125000] [drm:r600_gart_table_validate] *ERROR* Iter=0:
> >> unexpected value 0x745aaad1(expect 0xDEADBEEF)
> >> entry=0x000000000e008067, orignal=0x745aaad1
> >> ...
> >> /* System blocked here. */
> >>
> >> Any idea?
> >
> > I know lockup are frustrating, my only idea is the memory controller
> > is lockup because of some failing pci <-> system ram transaction.
> >
> >>
> >> BTW, we find the following in r600_pcie_gart_enable()
> >> (drivers/gpu/drm/radeon/r600.c):
> >> WREG32(VM_CONTEXT0_PROTECTION_FAULT_DEFAULT_ADDR,
> >> (u32)(rdev->dummy_page.addr >> 12));
> >>
> >> On our platform, PAGE_SIZE is 16K, does it have any problem?
> >
> > No this should be handled properly.
> >
> >> Also in radeon_gart_unbind() and radeon_gart_restore(), the logic
> >> should change to:
> >> for (j = 0; j < (PAGE_SIZE / RADEON_GPU_PAGE_SIZE); j++, t++) {
> >> radeon_gart_set_page(rdev, t, page_base);
> >> - page_base += RADEON_GPU_PAGE_SIZE;
> >> + if (page_base != rdev->dummy_page.addr)
> >> + page_base += RADEON_GPU_PAGE_SIZE;
> >> }
> >> ???
> >
> > No need to do so, dummy page will be 16K too, so it's fine.
> Really? When CPU page is 16K and GPU page is 4k, suppose the dummy page
> is 0x8e004000, then there are four types of address in GART:0x8e004000,
> 0x8e005000, 0x8e006000, 0x8e007000. The value which written in
> VM_CONTEXT0_PROTECTION_FAULT_DEFAULT_ADDR is 0x8e004 (0x8e004000<<12). I
> don't know how VM_CONTEXT0_PROTECTION_FAULT_DEFAULT_ADDR works, but I
> think 0x8e005000, 0x8e006000 and 0x8e007000 cannot be handled correctly.
When radeon_gart_unbind initialize the gart entry to point to the dummy
page it's just to have something safe in the GART table.
VM_CONTEXT0_PROTECTION_FAULT_DEFAULT_ADDR is the page address used when
there is a fault happening. It's like a sandbox for the mc. It doesn't
conflict in anyway to have gart table entry to point to same page.
Cheers,
Jerome
_______________________________________________
dri-devel mailing list
dri-devel@xxxxxxxxxxxxxxxxxxxxx
http://lists.freedesktop.org/mailman/listinfo/dri-devel
