On 27-09-18, 11:23, Georgi Djakov wrote:
> On 08/27/2018 06:11 PM, Jordan Crouse wrote:
> > Add the "opp-interconnect-bw" property to specify the
> > average and peak bandwidth for an interconnect path for
> > a specific operating power point. A separate bandwidth
> > pair can be specified for each of the interconnects
> > defined for the device by appending the interconnect
> > name to the property.
> >
> > Signed-off-by: Jordan Crouse <jcrouse@xxxxxxxxxxxxxx>
> > ---
> > Documentation/devicetree/bindings/opp/opp.txt | 36 +++++++++++++++++++
> > 1 file changed, 36 insertions(+)
> >
> > diff --git a/Documentation/devicetree/bindings/opp/opp.txt b/Documentation/devicetree/bindings/opp/opp.txt
> > index c396c4c0af92..d714c084f36d 100644
> > --- a/Documentation/devicetree/bindings/opp/opp.txt
> > +++ b/Documentation/devicetree/bindings/opp/opp.txt
> > @@ -170,6 +170,11 @@ Optional properties:
> > functioning of the current device at the current OPP (where this property is
> > present).
> >
> > +- opp-interconnect-bw-<name>: This is an array of pairs specifying the average
> > + and peak bandwidth in bytes per second for the interconnect path known by
> > + 'name'. This should match the name(s) specified by interconnect-names in the
> > + device definition.
> > +
> > Example 1: Single cluster Dual-core ARM cortex A9, switch DVFS states together.
> >
> > / {
> > @@ -543,3 +548,34 @@ Example 6: opp-microvolt-<name>, opp-microamp-<name>:
> > };
> > };
> > };
> > +
> > +Example 7: opp-interconnect-bw:
> > +(example: leaf device with frequency and BW quotas)
> > +
> > +/ {
> > + soc {
> > + gpu@5000000 {
> > + ...
> > + interconnects = <&qnoc 26 &qnoc 512>;
> > + interconnect-names = "port0";
> > + ...
> > + operating-points-v2 = <&gpu_opp_table>;
> > + };
> > + };
> > +
> > + gpu_opp_table: opp_table0 {
> > + compatible = "operating-points-v2";
> > +
> > + opp-710000000 {
> > + op-hz = /bits/ 64 <710000000>;
> > + /* Set peak bandwidth @ 7216000 KB/s */
> > + opp-interconnect-bw-port0 = /bits/ 64 <0 7216000000>;
>
> This seems a bit long. I would suggest the following instead.
> If there is only one path:
> /* average bandwidth = 0 KB/s, peak bandwidth = 7216000 KB/s */
> opp-bw-KBps = <0 7216000>;
> or
> opp-bw-MBps = <0 7216>;
>
> If there are multiple paths:
> opp-bw-KBps-port0 = <0 7216000>;
> opp-bw-KBps-port1 = <0 1000000>;
>
> The above follows a convention similar to opp-microvolt, where at
> runtime the platform can pick a <name> and a matching opp-bw-KBps-<name>
> property. If the platform doesn't pick a specific <name> or <name> does
> not match with any of the opp-bw-KBps-<name> properties, then
> opp-bw-KBps shall be used if present.
> For now supporting only KBps values seems enough to cover all present
> platforms, so we can start with this and based on the requirements of
> future platforms we can add MBps etc.
+1
And yes I am fine with such bindings getting introduced to the OPP
core.
I am not sure if this would fit well, but have a look at
"required-opps" property in OPP bindings and see if that can be used
instead of adding new bindings here. Again, I am not sure if that
should be done :)
--
viresh
_______________________________________________
dri-devel mailing list
dri-devel@xxxxxxxxxxxxxxxxxxxxx
https://lists.freedesktop.org/mailman/listinfo/dri-devel
