Hi Sean Sure, I will address these in v8. Thanks Abhinav On 2018-09-20 08:52, Sean Paul wrote:
On Wed, Sep 19, 2018 at 07:55:39PM -0700, Abhinav Kumar wrote:From: "abhinavk@xxxxxxxxxxxxxx" <abhinavk@xxxxxxxxxxxxxx> Add support for Truly NT35597 panel driver used in MSM reference platforms. This panel driver supports both single DSI and dual DSI modes. However, this patch series adds support only for dual DSI mode. Changes in v7: - Make the panel commands, name and mode as const - Configure the reset pin as active low in the device tree and adjust the reset sequence - Remove the macros to call the functions - Fix return conditions in the panel prepare call - Change the compatible string to have only the panel driver and the resolution details Signed-off-by: Archit Taneja <architt@xxxxxxxxxxxxxx> Signed-off-by: Abhinav Kumar <abhinavk@xxxxxxxxxxxxxx>Hey Abhinav,Thanks for revising the patch. I'm a bit torn on sending more feedback since you're already on v7 and it's been on-list for a while. Unfortunately I think there's enough to warrant a respin, so apologies for keeping this thing inlimbo, but hopefully we're converging.--- drivers/gpu/drm/panel/Kconfig | 8 + drivers/gpu/drm/panel/Makefile | 1 +drivers/gpu/drm/panel/panel-truly-nt35597.c | 706 ++++++++++++++++++++++++++++3 files changed, 715 insertions(+) create mode 100644 drivers/gpu/drm/panel/panel-truly-nt35597.cdiff --git a/drivers/gpu/drm/panel/Kconfig b/drivers/gpu/drm/panel/Kconfigindex 6020c30..7ae74c2 100644 --- a/drivers/gpu/drm/panel/Kconfig +++ b/drivers/gpu/drm/panel/Kconfig @@ -186,4 +186,12 @@ config DRM_PANEL_SITRONIX_ST7789V Say Y here if you want to enable support for the Sitronix ST7789V controller for 240x320 LCD panels +config DRM_PANEL_TRULY_NT35597_WQXGA + tristate "Truly WQXGA" + depends on OF + depends on DRM_MIPI_DSI + select VIDEOMODE_HELPERSI don't think you're using the videomode stuff any longer?+ help+ Say Y here if you want to enable support for Truly NT35597 WQXGA Dual DSI+ Video Mode panel endmenudiff --git a/drivers/gpu/drm/panel/Makefile b/drivers/gpu/drm/panel/Makefileindex 5ccaaa9..80fd19f 100644 --- a/drivers/gpu/drm/panel/Makefile +++ b/drivers/gpu/drm/panel/Makefile@@ -19,3 +19,4 @@ obj-$(CONFIG_DRM_PANEL_SEIKO_43WVF1G) += panel-seiko-43wvf1g.o obj-$(CONFIG_DRM_PANEL_SHARP_LQ101R1SX01) += panel-sharp-lq101r1sx01.o obj-$(CONFIG_DRM_PANEL_SHARP_LS043T1LE01) += panel-sharp-ls043t1le01.oobj-$(CONFIG_DRM_PANEL_SITRONIX_ST7789V) += panel-sitronix-st7789v.o +obj-$(CONFIG_DRM_PANEL_TRULY_NT35597_WQXGA) += panel-truly-nt35597.odiff --git a/drivers/gpu/drm/panel/panel-truly-nt35597.c b/drivers/gpu/drm/panel/panel-truly-nt35597.cnew file mode 100644 index 0000000..a070d0f --- /dev/null +++ b/drivers/gpu/drm/panel/panel-truly-nt35597.c @@ -0,0 +1,706 @@ +// SPDX-License-Identifier: GPL-2.0 +/* + * Copyright (c) 2018, The Linux Foundation. All rights reserved. + */ + +#include <linux/gpio/consumer.h> +#include <linux/of_graph.h> +#include <linux/regulator/consumer.h> +#include <linux/pinctrl/consumer.h> +#include <linux/of_device.h> + +#include <video/mipi_display.h> +#include <video/of_videomode.h> +#include <video/videomode.h>Same comment here re: videomode+ +#include <drm/drmP.h> +#include <drm/drm_panel.h> +#include <drm/drm_mipi_dsi.h> + +static const char * const regulator_names[] = { + "vdda", + "vdispp", + "vdispn", +}; + +static unsigned long const regulator_enable_loads[] = { + 62000, + 100000, + 100000, +}; + +static unsigned long const regulator_disable_loads[] = { + 80, + 100, + 100, +}; + +struct nt35597_config { + u32 width_mm; + u32 height_mm; + const char *panel_name; + const void *panel_on_cmds; + u32 num_on_cmds; + const struct drm_display_mode *dm; +}; + +struct truly_nt35597 { + struct device *dev; + struct drm_panel panel; + + struct regulator_bulk_data supplies[ARRAY_SIZE(regulator_names)]; + + struct gpio_desc *reset_gpio; + struct gpio_desc *mode_gpio; + + struct backlight_device *backlight; + + struct mipi_dsi_device *dsi[2]; + + const struct nt35597_config *config; + bool prepared; + bool enabled; +}; ++static inline struct truly_nt35597 *panel_to_ctx(struct drm_panel *panel)+{ + return container_of(panel, struct truly_nt35597, panel); +} + +#define MAX_LEN 5Aside from the ambiguous name, this is only used in one place and seems like it's 1 byte too big. Could you please just declare commands as 'u8 commands[4];'below?+#define SHORT_PACKET 2 +#define LONG_PACKET 4SHORT_PACKET and LONG_PACKET aren't used anywhere+ +struct cmd_set { + u8 commands[MAX_LEN]; + u8 size; +}; + +static struct cmd_set qcom_2k_panel_magic_cmds[] = { + /* CMD2_P0 */ + { { 0xff, 0x20 }, 2 }, + { { 0xfb, 0x01 }, 2 }, + { { 0x00, 0x01 }, 2 }, + { { 0x01, 0x55 }, 2 }, + { { 0x02, 0x45 }, 2 }, + { { 0x05, 0x40 }, 2 }, + { { 0x06, 0x19 }, 2 }, + { { 0x07, 0x1e }, 2 }, + { { 0x0b, 0x73 }, 2 }, + { { 0x0c, 0x73 }, 2 }, + { { 0x0e, 0xb0 }, 2 }, + { { 0x0f, 0xae }, 2 }, + { { 0x11, 0xb8 }, 2 }, + { { 0x13, 0x00 }, 2 }, + { { 0x58, 0x80 }, 2 }, + { { 0x59, 0x01 }, 2 }, + { { 0x5a, 0x00 }, 2 }, + { { 0x5b, 0x01 }, 2 }, + { { 0x5c, 0x80 }, 2 }, + { { 0x5d, 0x81 }, 2 }, + { { 0x5e, 0x00 }, 2 }, + { { 0x5f, 0x01 }, 2 }, + { { 0x72, 0x11 }, 2 }, + { { 0x68, 0x03 }, 2 }, + /* CMD2_P4 */ + { { 0xFF, 0x24 }, 2 }, + { { 0xFB, 0x01 }, 2 }, + { { 0x00, 0x1C }, 2 }, + { { 0x01, 0x0B }, 2 }, + { { 0x02, 0x0C }, 2 }, + { { 0x03, 0x01 }, 2 }, + { { 0x04, 0x0F }, 2 }, + { { 0x05, 0x10 }, 2 }, + { { 0x06, 0x10 }, 2 }, + { { 0x07, 0x10 }, 2 }, + { { 0x08, 0x89 }, 2 }, + { { 0x09, 0x8A }, 2 }, + { { 0x0A, 0x13 }, 2 }, + { { 0x0B, 0x13 }, 2 }, + { { 0x0C, 0x15 }, 2 }, + { { 0x0D, 0x15 }, 2 }, + { { 0x0E, 0x17 }, 2 }, + { { 0x0F, 0x17 }, 2 }, + { { 0x10, 0x1C }, 2 }, + { { 0x11, 0x0B }, 2 }, + { { 0x12, 0x0C }, 2 }, + { { 0x13, 0x01 }, 2 }, + { { 0x14, 0x0F }, 2 }, + { { 0x15, 0x10 }, 2 }, + { { 0x16, 0x10 }, 2 }, + { { 0x17, 0x10 }, 2 }, + { { 0x18, 0x89 }, 2 }, + { { 0x19, 0x8A }, 2 }, + { { 0x1A, 0x13 }, 2 }, + { { 0x1B, 0x13 }, 2 }, + { { 0x1C, 0x15 }, 2 }, + { { 0x1D, 0x15 }, 2 }, + { { 0x1E, 0x17 }, 2 }, + { { 0x1F, 0x17 }, 2 }, + /* STV */ + { { 0x20, 0x40 }, 2 }, + { { 0x21, 0x01 }, 2 }, + { { 0x22, 0x00 }, 2 }, + { { 0x23, 0x40 }, 2 }, + { { 0x24, 0x40 }, 2 }, + { { 0x25, 0x6D }, 2 }, + { { 0x26, 0x40 }, 2 }, + { { 0x27, 0x40 }, 2 }, + /* Vend */ + { { 0xE0, 0x00 }, 2 }, + { { 0xDC, 0x21 }, 2 }, + { { 0xDD, 0x22 }, 2 }, + { { 0xDE, 0x07 }, 2 }, + { { 0xDF, 0x07 }, 2 }, + { { 0xE3, 0x6D }, 2 }, + { { 0xE1, 0x07 }, 2 }, + { { 0xE2, 0x07 }, 2 }, + /* UD */ + { { 0x29, 0xD8 }, 2 }, + { { 0x2A, 0x2A }, 2 }, + /* CLK */ + { { 0x4B, 0x03 }, 2 }, + { { 0x4C, 0x11 }, 2 }, + { { 0x4D, 0x10 }, 2 }, + { { 0x4E, 0x01 }, 2 }, + { { 0x4F, 0x01 }, 2 }, + { { 0x50, 0x10 }, 2 }, + { { 0x51, 0x00 }, 2 }, + { { 0x52, 0x80 }, 2 }, + { { 0x53, 0x00 }, 2 }, + { { 0x56, 0x00 }, 2 }, + { { 0x54, 0x07 }, 2 }, + { { 0x58, 0x07 }, 2 }, + { { 0x55, 0x25 }, 2 }, + /* Reset XDONB */ + { { 0x5B, 0x43 }, 2 }, + { { 0x5C, 0x00 }, 2 }, + { { 0x5F, 0x73 }, 2 }, + { { 0x60, 0x73 }, 2 }, + { { 0x63, 0x22 }, 2 }, + { { 0x64, 0x00 }, 2 }, + { { 0x67, 0x08 }, 2 }, + { { 0x68, 0x04 }, 2 }, + /* Resolution:1440x2560 */ + { { 0x72, 0x02 }, 2 }, + /* mux */ + { { 0x7A, 0x80 }, 2 }, + { { 0x7B, 0x91 }, 2 }, + { { 0x7C, 0xD8 }, 2 }, + { { 0x7D, 0x60 }, 2 }, + { { 0x7F, 0x15 }, 2 }, + { { 0x75, 0x15 }, 2 }, + /* ABOFF */ + { { 0xB3, 0xC0 }, 2 }, + { { 0xB4, 0x00 }, 2 }, + { { 0xB5, 0x00 }, 2 }, + /* Source EQ */ + { { 0x78, 0x00 }, 2 }, + { { 0x79, 0x00 }, 2 }, + { { 0x80, 0x00 }, 2 }, + { { 0x83, 0x00 }, 2 }, + /* FP BP */ + { { 0x93, 0x0A }, 2 }, + { { 0x94, 0x0A }, 2 }, + /* Inversion Type */ + { { 0x8A, 0x00 }, 2 }, + { { 0x9B, 0xFF }, 2 }, + /* IMGSWAP =1 @PortSwap=1 */ + { { 0x9D, 0xB0 }, 2 }, + { { 0x9F, 0x63 }, 2 }, + { { 0x98, 0x10 }, 2 }, + /* FRM */ + { { 0xEC, 0x00 }, 2 }, + /* CMD1 */ + { { 0xFF, 0x10 }, 2 }, + /* VBP+VSA=,VFP = 10H */ + { { 0x3B, 0x03, 0x0A, 0x0A }, 4 }, + /* FTE on */ + { { 0x35, 0x00 }, 2 }, + /* EN_BK =1(auto black) */ + { { 0xE5, 0x01 }, 2 }, + /* CMD mode(10) VDO mode(03) */ + { { 0xBB, 0x03 }, 2 }, + /* Non Reload MTP */ + { { 0xFB, 0x01 }, 2 }, +}; + +static int truly_dcs_write(struct drm_panel *panel, u32 command) +{ + struct truly_nt35597 *ctx = panel_to_ctx(panel); + int i, ret; + + for (i = 0; i < ARRAY_SIZE(ctx->dsi); i++) { + ret = mipi_dsi_dcs_write(ctx->dsi[i], + command, NULL, 0);This can fit on one line+ if (ret < 0) { + DRM_DEV_ERROR(ctx->dev, + "cmd 0x%x failed for dsi = %d\n", command, + i); + } + } + + return ret; +} + +static int truly_dcs_write_buf(struct drm_panel *panel, + u32 size, u8 *buf) +{ + struct truly_nt35597 *ctx = panel_to_ctx(panel); + int ret = 0; + int i; + + for (i = 0; i < ARRAY_SIZE(ctx->dsi); i++) { + ret = mipi_dsi_dcs_write_buffer(ctx->dsi[i], + buf, + size);This can fit on one line+ + if (ret < 0) { + DRM_DEV_ERROR(ctx->dev, + "failed to tx cmd [%d], err: %d\n", + i, ret); + return ret; + } + } + + return ret; +} + +static int truly_35597_power_on(struct truly_nt35597 *ctx) +{ + int ret, i; + + for (i = 0; i < ARRAY_SIZE(ctx->supplies); i++) { + ret = regulator_set_load(ctx->supplies[i].consumer, + regulator_enable_loads[i]); + if (ret) + return ret; + } ++ ret = regulator_bulk_enable(ARRAY_SIZE(ctx->supplies), ctx->supplies);+ if (ret < 0) + return ret; + + /* Reset sequence of truly panel requires + * the reset pin to be pulled high for 10ms + * followed by a low period of 10ms and thenThe highs and lows are backwards in this comment. Your also way inside 80 chars for this comment. Perhaps it was previously indented a bunch and hasn't been reflowed? Anyways, it might be more clear if you don't talk about what the pinis doing, but rather the reset state of the panel: /** Reset sequence of truly panel requires the panel to be out of reset * for 10ms, followed by being held in reset for 10ms and then out again*/+ * pulled high again + */ + + gpiod_set_value(ctx->reset_gpio, 0); + usleep_range(10000, 20000); + gpiod_set_value(ctx->reset_gpio, 1); + usleep_range(10000, 20000); + gpiod_set_value(ctx->reset_gpio, 0); + + return 0; +} + +static int truly_nt35597_power_off(struct truly_nt35597 *ctx) +{ + int ret, i; + + gpiod_set_value(ctx->reset_gpio, 1); + + for (i = 0; i < ARRAY_SIZE(ctx->supplies); i++) { + ret = regulator_set_load(ctx->supplies[i].consumer, + regulator_disable_loads[i]); + if (ret) + return ret; + } ++ return regulator_bulk_disable(ARRAY_SIZE(ctx->supplies), ctx->supplies);+} + +static int truly_nt35597_disable(struct drm_panel *panel) +{ + struct truly_nt35597 *ctx = panel_to_ctx(panel); + int ret; + + if (!ctx->enabled) + return 0; + + if (ctx->backlight) { + ret = backlight_disable(ctx->backlight); + if (ret < 0) + DRM_DEV_ERROR(ctx->dev, "backlight disable failed %d\n", + ret); + } + + ctx->enabled = false; + return 0; +} + +static int truly_nt35597_unprepare(struct drm_panel *panel) +{ + struct truly_nt35597 *ctx = panel_to_ctx(panel); + int ret = 0; + + if (!ctx->prepared) + return 0; + + ctx->dsi[0]->mode_flags = 0; + ctx->dsi[1]->mode_flags = 0; + + ret = truly_dcs_write(panel, MIPI_DCS_SET_DISPLAY_OFF); + if (ret < 0) { + DRM_DEV_ERROR(ctx->dev, + "set_display_off cmd failed ret = %d\n", + ret); + } + + /* 120ms delay required here as per DCS spec */ + msleep(120); + + ret = truly_dcs_write(panel, MIPI_DCS_ENTER_SLEEP_MODE); + if (ret < 0) { + DRM_DEV_ERROR(ctx->dev, + "enter_sleep cmd failed ret = %d\n", + ret); + } + + ret = truly_nt35597_power_off(ctx); + if (ret < 0) + DRM_DEV_ERROR(ctx->dev, + "truly_nt35597_power_off failed ret = %d\n", + ret); + + ctx->prepared = false; + return ret; +} + +static int truly_nt35597_prepare(struct drm_panel *panel) +{ + struct truly_nt35597 *ctx = panel_to_ctx(panel); + int ret; + int i; + struct cmd_set *panel_on_cmds; + const struct nt35597_config *config; + u32 num_cmds; + + if (ctx->prepared) + return 0; + + ret = truly_35597_power_on(ctx); + if (ret < 0) + return ret; + + ctx->dsi[0]->mode_flags |= MIPI_DSI_MODE_LPM; + ctx->dsi[1]->mode_flags |= MIPI_DSI_MODE_LPM; + + config = ctx->config; + panel_on_cmds = (struct cmd_set *)config->panel_on_cmds; + num_cmds = config->num_on_cmds; + + for (i = 0; i < num_cmds; i++) { + ret = truly_dcs_write_buf(panel, + panel_on_cmds[i].size, + panel_on_cmds[i].commands); + if (ret < 0) { + DRM_DEV_ERROR(ctx->dev, + "cmd set tx failed i = %d ret = %d\n", + i, ret); + goto power_off; + } + } + + /* As per DSI spec need to wait for 120ms + * after sending the exit sleep DCS command + */This comment seems like it's in the wrong place. Also, multi-line comments areformatted as follows: /* * multi-line * comment */If you like to save space, like me, you could probably fit this on 1 line like:/* Per DSI spec, wait 120ms after sending the exit sleep DCS command */+ + ret = truly_dcs_write(panel, MIPI_DCS_EXIT_SLEEP_MODE); + if (ret < 0) { + DRM_DEV_ERROR(ctx->dev, + "exit_sleep_mode cmd failed ret = %d\n", + ret); + goto power_off; + } + + msleep(120); + + ret = truly_dcs_write(panel, MIPI_DCS_SET_DISPLAY_ON); + if (ret < 0) { + DRM_DEV_ERROR(ctx->dev, + "set_display_on cmd failed ret = %d\n", + ret); + goto power_off; + } + + /* Adding 120ms delay before the start of + * pixel stream to the panel after sending + * the set_display_on DCS command + */ + + msleep(120); + + ctx->prepared = true; + + return 0; + +power_off: + gpiod_set_value(ctx->reset_gpio, 1); + + for (i = 0; i < ARRAY_SIZE(ctx->supplies); i++) + regulator_set_load(ctx->supplies[i].consumer, + regulator_disable_loads[i]); + + ret = regulator_bulk_disable(ARRAY_SIZE(ctx->supplies), + ctx->supplies);This seems like a straight copy of truly_nt35597_power_off(), just call thatfunction.+ DRM_DEV_ERROR(ctx->dev, + "regulator disable failed, %d\n", ret);This fits on one line.+ + return ret; +} + +static int truly_nt35597_enable(struct drm_panel *panel) +{ + struct truly_nt35597 *ctx = panel_to_ctx(panel); + int ret; + + if (ctx->enabled) + return 0; + + if (ctx->backlight) { + ret = backlight_enable(ctx->backlight); + if (ret < 0) + DRM_DEV_ERROR(ctx->dev, "backlight enable failed %d\n", + ret); + } + + ctx->enabled = true; + + return 0; +} + +static int truly_nt35597_get_modes(struct drm_panel *panel) +{ + struct drm_connector *connector = panel->connector; + struct truly_nt35597 *ctx = panel_to_ctx(panel); + struct drm_display_mode *mode; + const struct nt35597_config *config; + + config = ctx->config; + mode = drm_mode_create(connector->dev); + if (!mode) { + DRM_DEV_ERROR(ctx->dev, + "failed to create a new display mode\n"); + return 0; + } + + connector->display_info.width_mm = config->width_mm; + connector->display_info.height_mm = config->height_mm; + drm_mode_copy(mode, config->dm); + mode->type = DRM_MODE_TYPE_DRIVER | DRM_MODE_TYPE_PREFERRED; + drm_mode_probed_add(connector, mode); + + return 1; +} + +static const struct drm_panel_funcs truly_nt35597_drm_funcs = { + .disable = truly_nt35597_disable, + .unprepare = truly_nt35597_unprepare, + .prepare = truly_nt35597_prepare, + .enable = truly_nt35597_enable, + .get_modes = truly_nt35597_get_modes, +}; + +static int truly_nt35597_panel_add(struct truly_nt35597 *ctx) +{ + struct device *dev = ctx->dev; + int ret, i; + const struct nt35597_config *config; + + config = ctx->config; + for (i = 0; i < ARRAY_SIZE(ctx->supplies); i++) + ctx->supplies[i].supply = regulator_names[i]; + + ret = devm_regulator_bulk_get(dev, ARRAY_SIZE(ctx->supplies), + ctx->supplies); + if (ret < 0) + return ret; + + ctx->reset_gpio = devm_gpiod_get(dev, "reset", GPIOD_OUT_LOW); + if (IS_ERR(ctx->reset_gpio)) { + DRM_DEV_ERROR(dev, "cannot get reset gpio %ld\n", + PTR_ERR(ctx->reset_gpio)); + return PTR_ERR(ctx->reset_gpio); + } + + ctx->mode_gpio = devm_gpiod_get(dev, "mode", GPIOD_OUT_LOW); + if (IS_ERR(ctx->mode_gpio)) { + DRM_DEV_ERROR(dev, "cannot get mode gpio %ld\n", + PTR_ERR(ctx->mode_gpio)); + return PTR_ERR(ctx->mode_gpio); + } + + /* dual port */ + gpiod_set_value(ctx->mode_gpio, 0); + + drm_panel_init(&ctx->panel); + ctx->panel.dev = dev; + ctx->panel.funcs = &truly_nt35597_drm_funcs; + drm_panel_add(&ctx->panel); + + return 0; +} + +static const struct drm_display_mode qcom_sdm845_mtp_2k_mode = { + .name = "1440x2560", + .clock = 268316, + .hdisplay = 1440, + .hsync_start = 1440 + 200, + .hsync_end = 1440 + 200 + 32, + .htotal = 1440 + 200 + 32 + 64, + .vdisplay = 2560, + .vsync_start = 2560 + 8, + .vsync_end = 2560 + 8 + 1, + .vtotal = 2560 + 8 + 1 + 7, + .vrefresh = 60, + .flags = 0, +}; + +static const struct nt35597_config nt35597_dir = { + .width_mm = 74, + .height_mm = 131, + .panel_name = "qcom_sdm845_mtp_2k_panel", + .dm = &qcom_sdm845_mtp_2k_mode, + .panel_on_cmds = qcom_2k_panel_magic_cmds, + .num_on_cmds = ARRAY_SIZE(qcom_2k_panel_magic_cmds), +}; + +static int truly_nt35597_probe(struct mipi_dsi_device *dsi) +{ + struct device *dev = &dsi->dev; + struct truly_nt35597 *ctx; + struct mipi_dsi_device *dsi1_device; + struct device_node *dsi1; + struct mipi_dsi_host *dsi1_host; + struct mipi_dsi_device *dsi_dev; + int ret = 0; + int i; + + const struct mipi_dsi_device_info info = { + .type = "trulynt35597", + .channel = 0, + .node = NULL, + }; + + ctx = devm_kzalloc(dev, sizeof(*ctx), GFP_KERNEL); + + if (!ctx) + return -ENOMEM; + + /* This device represents itself as one with + * two input ports which are fed by the output + * ports of the two DSI controllers . The DSI0 + * is the master controller and has most of the + * panel related info in its child node. + */ + + ctx->config = of_device_get_match_data(dev); + + if (!ctx->config) { + dev_err(dev, "missing device configuration\n"); + return -ENODEV; + } + + dsi1 = of_graph_get_remote_node(dsi->dev.of_node, 1, -1); + if (!dsi1) { + DRM_DEV_ERROR(dev, + "failed to get remote node for dsi1_device\n"); + ret = -ENODEV; + goto err_get_remote;Just return directly.+ } + + dsi1_host = of_find_mipi_dsi_host_by_node(dsi1);Move that of_node_put(dsi1) here.+ if (!dsi1_host) { + DRM_DEV_ERROR(dev, "failed to find dsi host\n"); + ret = -EPROBE_DEFER; + goto err_host;Now you can return directly from here+ } + + of_node_put(dsi1); + + /* register the second DSI device */ + dsi1_device = mipi_dsi_device_register_full(dsi1_host, &info); + if (IS_ERR(dsi1_device)) { + DRM_DEV_ERROR(dev, "failed to create dsi device\n"); + ret = PTR_ERR(dsi); + goto err_dsi_device;And here+ } + + mipi_dsi_set_drvdata(dsi, ctx); + + ctx->dev = dev; + ctx->dsi[0] = dsi; + ctx->dsi[1] = dsi1_device; + + ret = truly_nt35597_panel_add(ctx); + if (ret) { + DRM_DEV_ERROR(dev, "failed to add panel\n"); + goto err_panel_add; + } + + for (i = 0; i < ARRAY_SIZE(ctx->dsi); i++) { + dsi_dev = ctx->dsi[i]; + dsi_dev->lanes = 4; + dsi_dev->format = MIPI_DSI_FMT_RGB888; + dsi_dev->mode_flags = MIPI_DSI_MODE_VIDEO | MIPI_DSI_MODE_LPM | + MIPI_DSI_CLOCK_NON_CONTINUOUS; + ret = mipi_dsi_attach(dsi_dev); + if (ret < 0) { + DRM_DEV_ERROR(dev, + "dsi attach failed i = %d\n", i); + goto err_dsi_attach; + } + } + + return 0; + +err_dsi_attach: + drm_panel_remove(&ctx->panel); +err_panel_add: + mipi_dsi_device_unregister(dsi1_device); +err_dsi_device: +err_host: + of_node_put(dsi1); +err_get_remote: + return ret; +} + +static int truly_nt35597_remove(struct mipi_dsi_device *dsi) +{ + struct truly_nt35597 *ctx = mipi_dsi_get_drvdata(dsi); + + if (ctx->dsi[0]) + mipi_dsi_detach(ctx->dsi[0]); + if (ctx->dsi[1]) { + mipi_dsi_detach(ctx->dsi[1]); + mipi_dsi_device_unregister(ctx->dsi[1]); + } + + drm_panel_remove(&ctx->panel); + return 0; +} + +static const struct of_device_id truly_nt35597_of_match[] = { + { .compatible = "truly,nt35597-2K-display", + .data = &nt35597_dir, + }, + + { } +}; +MODULE_DEVICE_TABLE(of, truly_nt35597_of_match); + +static struct mipi_dsi_driver truly_nt35597_driver = { + .driver = { + .name = "panel_truly_nt35597", + .of_match_table = truly_nt35597_of_match, + }, + .probe = truly_nt35597_probe, + .remove = truly_nt35597_remove, +}; +module_mipi_dsi_driver(truly_nt35597_driver); + +MODULE_DESCRIPTION("Truly NT35597 DSI Panel Driver"); +MODULE_LICENSE("GPL v2"); --The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,a Linux Foundation Collaborative Project _______________________________________________ dri-devel mailing list dri-devel@xxxxxxxxxxxxxxxxxxxxx https://lists.freedesktop.org/mailman/listinfo/dri-devel
_______________________________________________ dri-devel mailing list dri-devel@xxxxxxxxxxxxxxxxxxxxx https://lists.freedesktop.org/mailman/listinfo/dri-devel
