On Thu, Feb 09, 2012 at 12:03:17PM -0800, Benson Leung wrote: > gmbus_xfer with a single message (particularly a single message write) would > set Bus Cycle Select to 100b, the Gen Stop cycle, instead of 101b, > No Index, Stop cycle. This would not start single message i2c transactions. > > Also, gmbus_xfer done: will disable the interface without checking if > it is idle. In the case of writes, there will be no wait on status or delay > to ensure the write starts and completes before the interface is turned off. > > Fixed the former issue by using the same cycle selection as used in the > I2C_M_RD for the write case. > GMBUS_CYCLE_WAIT | (i + 1 == num ? GMBUS_CYCLE_STOP : 0) > Fixed the latter by waiting on GMBUS_ACTIVE to deassert before disable. > > Signed-off-by: Benson Leung <bleung@xxxxxxxxxxxx> Can you clarify the commit message a bit and say that the first hunk is just for optics and the issue is only with the write path (because the read path is correct already). Silly me is just to easily confused ;-) Btw, I've reworked the gmbus -> gpio bit-banging fallback code a bit and if that passes review and all I'll reenable gmbus by default again. See http://cgit.freedesktop.org/~danvet/drm/log/?h=gmbus Yours, Daniel > --- > drivers/gpu/drm/i915/intel_i2c.c | 13 +++++++++---- > 1 files changed, 9 insertions(+), 4 deletions(-) > > diff --git a/drivers/gpu/drm/i915/intel_i2c.c b/drivers/gpu/drm/i915/intel_i2c.c > index d30cccc..64bb9cd 100644 > --- a/drivers/gpu/drm/i915/intel_i2c.c > +++ b/drivers/gpu/drm/i915/intel_i2c.c > @@ -249,7 +249,8 @@ gmbus_xfer(struct i2c_adapter *adapter, > > if (msgs[i].flags & I2C_M_RD) { > I915_WRITE(GMBUS1 + reg_offset, > - GMBUS_CYCLE_WAIT | (i + 1 == num ? GMBUS_CYCLE_STOP : 0) | > + GMBUS_CYCLE_WAIT | > + (i + 1 == num ? GMBUS_CYCLE_STOP : 0) | > (len << GMBUS_BYTE_COUNT_SHIFT) | > (msgs[i].addr << GMBUS_SLAVE_ADDR_SHIFT) | > GMBUS_SLAVE_READ | GMBUS_SW_RDY); > @@ -278,7 +279,8 @@ gmbus_xfer(struct i2c_adapter *adapter, > > I915_WRITE(GMBUS3 + reg_offset, val); > I915_WRITE(GMBUS1 + reg_offset, > - (i + 1 == num ? GMBUS_CYCLE_STOP : GMBUS_CYCLE_WAIT) | > + GMBUS_CYCLE_WAIT | > + (i + 1 == num ? GMBUS_CYCLE_STOP : 0) | > (msgs[i].len << GMBUS_BYTE_COUNT_SHIFT) | > (msgs[i].addr << GMBUS_SLAVE_ADDR_SHIFT) | > GMBUS_SLAVE_WRITE | GMBUS_SW_RDY); > @@ -317,9 +319,12 @@ clear_err: > I915_WRITE(GMBUS1 + reg_offset, 0); > > done: > - /* Mark the GMBUS interface as disabled. We will re-enable it at the > - * start of the next xfer, till then let it sleep. > + /* Mark the GMBUS interface as disabled after waiting for idle. > + * We will re-enable it at the start of the next xfer, > + * till then let it sleep. > */ > + if (wait_for((I915_READ(GMBUS2 + reg_offset) & GMBUS_ACTIVE) == 0, 10)) > + DRM_INFO("GMBUS timed out waiting for idle\n"); > I915_WRITE(GMBUS0 + reg_offset, 0); > return i; > > -- > 1.7.1 > > _______________________________________________ > dri-devel mailing list > dri-devel@xxxxxxxxxxxxxxxxxxxxx > http://lists.freedesktop.org/mailman/listinfo/dri-devel -- Daniel Vetter Mail: daniel@xxxxxxxx Mobile: +41 (0)79 365 57 48 _______________________________________________ dri-devel mailing list dri-devel@xxxxxxxxxxxxxxxxxxxxx http://lists.freedesktop.org/mailman/listinfo/dri-devel
