On Monday, 17 September 2018 11:54:04 EEST Laurent Pinchart wrote:
> Hi Simon,
>
> On Monday, 17 September 2018 11:47:15 EEST Laurent Pinchart wrote:
> > On Monday, 17 September 2018 11:14:20 EEST Simon Horman wrote:
> > > On Mon, Sep 17, 2018 at 09:50:55AM +0200, Simon Horman wrote:
> > > > On Fri, Sep 14, 2018 at 12:10:43PM +0300, Laurent Pinchart wrote:
> > > > > The R8A77990 (E3) platform has one RGB output and two LVDS outputs
> > > > > connected to the DU. Add the DT nodes for the DU, LVDS encoders and
> > > > > supporting VSP and FCP.
> > > > >
> > > > > Signed-off-by: Laurent Pinchart
> > > > > <laurent.pinchart+renesas@xxxxxxxxxxxxxxxx>
> > > > > Tested-by: Jacopo Mondi <jacopo+renesas@xxxxxxxxxx>
> > > > > ---
> > > > >
> > > > > arch/arm64/boot/dts/renesas/r8a77990.dtsi | 167
> > > > > +++++++++++++++++++++++
> > > > > 1 file changed, 167 insertions(+)
> > > > >
> > > > > diff --git a/arch/arm64/boot/dts/renesas/r8a77990.dtsi
> > > > > b/arch/arm64/boot/dts/renesas/r8a77990.dtsi index
> > > > > abb14af76c0e..600074ca3ee5 100644
> > > > > --- a/arch/arm64/boot/dts/renesas/r8a77990.dtsi
> > > > > +++ b/arch/arm64/boot/dts/renesas/r8a77990.dtsi
> > > > > @@ -537,6 +537,173 @@
> > > > >
> > > > > resets = <&cpg 408>;
> > > > >
> > > > > };
> > > >
> > > > These nodes should be placed after the gic to preserve the sorting
> > > > of nodes by bus address and then IP block.
> > > >
> > > > > + vspb0: vsp@fe960000 {
> > > > > + compatible = "renesas,vsp2";
> > > > > + reg = <0 0xfe960000 0 0x8000>;
> > > > > + interrupts = <GIC_SPI 266 IRQ_TYPE_LEVEL_HIGH>;
> > > > > + clocks = <&cpg CPG_MOD 626>;
> > > > > + power-domains = <&sysc R8A77990_PD_ALWAYS_ON>;
> > > > > + resets = <&cpg 626>;
> > > > > + renesas,fcp = <&fcpvb0>;
> > > > > + };
> > > > > +
> > > > > + fcpvb0: fcp@fe96f000 {
> > > > > + compatible = "renesas,fcpv";
> > > > > + reg = <0 0xfe96f000 0 0x200>;
> > > > > + clocks = <&cpg CPG_MOD 607>;
> > > > > + power-domains = <&sysc R8A77990_PD_ALWAYS_ON>;
> > > > > + resets = <&cpg 607>;
> > > > > + iommus = <&ipmmu_vp0 5>;
> > > > > + };
> > > > > +
> > > > > + vspi0: vsp@fe9a0000 {
> > > > > + compatible = "renesas,vsp2";
> > > > > + reg = <0 0xfe9a0000 0 0x8000>;
> > > > > + interrupts = <GIC_SPI 444 IRQ_TYPE_LEVEL_HIGH>;
> > > > > + clocks = <&cpg CPG_MOD 622>;
> > > >
> > > > R-Car Series, 3rd Generation, v1.00, Table Table 8A.21 indicates
> > > > that this clock should be <&cpg CPG_MOD 631>. The clock above is
> > > > (according to my reading of the documentation) correctly
> > > > used for vspd1 below.
> > > >
> > > > > + power-domains = <&sysc R8A77990_PD_ALWAYS_ON>;
> > > > > + resets = <&cpg 631>;
> > > > > + renesas,fcp = <&fcpvi0>;
> > > > > + };
> > > > > +
> > > > > + fcpvi0: fcp@fe9af000 {
> > > > > + compatible = "renesas,fcpv";
> > > > > + reg = <0 0xfe9af000 0 0x200>;
> > > > > + clocks = <&cpg CPG_MOD 611>;
> > > > > + power-domains = <&sysc R8A77990_PD_ALWAYS_ON>;
> > > > > + resets = <&cpg 611>;
> > > > > + iommus = <&ipmmu_vp0 8>;
> > > > > + };
> > > > > +
> > > > > + vspd0: vsp@fea20000 {
> > > > > + compatible = "renesas,vsp2";
> > > > > + reg = <0 0xfea20000 0 0x7000>;
> > > > > + interrupts = <GIC_SPI 466 IRQ_TYPE_LEVEL_HIGH>;
> > > > > + clocks = <&cpg CPG_MOD 623>;
> > > > > + power-domains = <&sysc R8A77990_PD_ALWAYS_ON>;
> > > > > + resets = <&cpg 623>;
> > > > > + renesas,fcp = <&fcpvd0>;
> > > > > + };
> > > > > +
> > > > > + fcpvd0: fcp@fea27000 {
> > > > > + compatible = "renesas,fcpv";
> > > > > + reg = <0 0xfea27000 0 0x200>;
> > > > > + clocks = <&cpg CPG_MOD 603>;
> > > > > + power-domains = <&sysc R8A77990_PD_ALWAYS_ON>;
> > > > > + resets = <&cpg 603>;
> > > > > + iommus = <&ipmmu_vi0 8>;
> > > > > + };
> > > > > +
> > > > > + vspd1: vsp@fea28000 {
> > > > > + compatible = "renesas,vsp2";
> > > > > + reg = <0 0xfea28000 0 0x7000>;
> > > > > + interrupts = <GIC_SPI 467 IRQ_TYPE_LEVEL_HIGH>;
> > > > > + clocks = <&cpg CPG_MOD 622>;
> > > > > + power-domains = <&sysc R8A77990_PD_ALWAYS_ON>;
> > > > > + resets = <&cpg 622>;
> > > > > + renesas,fcp = <&fcpvd1>;
> > > > > + };
> > > > > +
> > > > > + fcpvd1: fcp@fea2f000 {
> > > > > + compatible = "renesas,fcpv";
> > > > > + reg = <0 0xfea2f000 0 0x200>;
> > > > > + clocks = <&cpg CPG_MOD 602>;
> > > > > + power-domains = <&sysc R8A77990_PD_ALWAYS_ON>;
> > > > > + resets = <&cpg 602>;
> > > > > + iommus = <&ipmmu_vi0 9>;
> > > > > + };
> > > > > +
> > > > > + du: display@feb00000 {
> > > > > + compatible = "renesas,du-r8a77990";
> > > > > + reg = <0 0xfeb00000 0 0x80000>;
> > > > > + interrupts = <GIC_SPI 256 IRQ_TYPE_LEVEL_HIGH>,
> > > > > + <GIC_SPI 268 IRQ_TYPE_LEVEL_HIGH>;
> > > > > + clocks = <&cpg CPG_MOD 724>,
> > > > > + <&cpg CPG_MOD 723>;
> > > > > + clock-names = "du.0", "du.1";
> > > > > + vsps = <&vspd0 0 &vspd1 0>;
> > > > > + status = "disabled";
> > > > > +
> > > > > + ports {
> > > > > + #address-cells = <1>;
> > > > > + #size-cells = <0>;
> > > > > +
> > > > > + port@0 {
> > > > > + reg = <0>;
> > > > > + du_out_rgb: endpoint {
> > > > > + };
> > > > > + };
> > > > > +
> > > > > + port@1 {
> > > > > + reg = <1>;
> > > > > + du_out_lvds0: endpoint {
> > > > > + remote-endpoint = <&lvds0_in>;
> > > > > + };
> > > > > + };
> > > > > +
> > > > > + port@2 {
> > > > > + reg = <2>;
> > > > > + du_out_lvds1: endpoint {
> > > > > + remote-endpoint = <&lvds1_in>;
> > > > > + };
> > > > > + };
> > > > > + };
> > > > > + };
> > > > > +
> > > > > + lvds0: lvds-encoder@feb90000 {
> > > > > + compatible = "renesas,r8a77990-lvds";
> > > > > + reg = <0 0xfeb90000 0 0x20>;
> > > > > + clocks = <&cpg CPG_MOD 727>;
> > > > > + power-domains = <&sysc R8A77990_PD_ALWAYS_ON>;
> > > > > + resets = <&cpg 727>;
> > > > > + status = "disabled";
> > > > > +
> > > > > + ports {
> > > > > + #address-cells = <1>;
> > > > > + #size-cells = <0>;
> > > > > +
> > > > > + port@0 {
> > > > > + reg = <0>;
> > > > > + lvds0_in: endpoint {
> > > > > + remote-endpoint = <&du_out_lvds0>;
> > > > > + };
> > > > > + };
> > > > > +
> > > > > + port@1 {
> > > > > + reg = <1>;
> > > > > + lvds0_out: endpoint {
> > > > > + };
> > > > > + };
> > > > > + };
> > > > > + };
> > > > > +
> > > > > + lvds1: lvds-encoder@feb90100 {
> > > > > + compatible = "renesas,r8a77990-lvds";
> > > > > + reg = <0 0xfeb90100 0 0x20>;
> > > > > + clocks = <&cpg CPG_MOD 727>;
> > > > > + power-domains = <&sysc R8A77990_PD_ALWAYS_ON>;
> > > > > + resets = <&cpg 726>;
> > >
> > > Also, is the missmatch between the index for the clock and reset
> > > intentional?
> >
> > It is. According to the datasheet, the two LVDS encoders have different
> > module stop bits, but share the same reset (lovely hardware design, it
> > will be fun to support that in the driver :-S).
>
> Sorry, I got it wrong. it's bit 725 that is shared between the two LVDS
> encoders, to reset the two LVDS PLLs together. The encoders themselves still
> have independent reset bits. I'll fix this.
And of course it's the clock you were commenting on, not the reset. *sigh*
According to the datasheets the two LVDS encoders share one MSTP. Whether
that's a mistake in the documentation or not I can't tell yet, as I have only
tested LVDS0.
> > > > > + status = "disabled";
> > > > > +
> > > > > + ports {
> > > > > + #address-cells = <1>;
> > > > > + #size-cells = <0>;
> > > > > +
> > > > > + port@0 {
> > > > > + reg = <0>;
> > > > > + lvds1_in: endpoint {
> > > > > + remote-endpoint = <&du_out_lvds1>;
> > > > > + };
> > > > > + };
> > > > > +
> > > > > + port@1 {
> > > > > + reg = <1>;
> > > > > + lvds1_out: endpoint {
> > > > > + };
> > > > > + };
> > > > > + };
> > > > > + };
> > > > > +
> > > > >
> > > > > prr: chipid@fff00044 {
> > > > >
> > > > > compatible = "renesas,prr";
> > > > > reg = <0 0xfff00044 0 4>;
--
Regards,
Laurent Pinchart
_______________________________________________
dri-devel mailing list
dri-devel@xxxxxxxxxxxxxxxxxxxxx
https://lists.freedesktop.org/mailman/listinfo/dri-devel
