Re: [PATCH v1 2/7] dt-binding: add bindings for Atmel LCDC mfd

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On Sun, 12 Aug 2018 20:46:24 +0200
Sam Ravnborg <sam@xxxxxxxxxxxx> wrote:

> The LCDC IP used by some Atmel SOC's have a
> multifunction device that include two sub-devices:
> - pwm
> - display controller
> 
> This binding describe the multi function device
> that act as root for the sub-devices
> 
> The Atmel SOC's are at91sam9 etc.
> 
> The compatible name is intentionally
> prefixed with -mfd to avoid clash with existing
> compatible entries.
> 
> Signed-off-by: Sam Ravnborg <sam@xxxxxxxxxxxx>
> Cc: Lee Jones <lee.jones@xxxxxxxxxx>
> Cc: Boris Brezillon <boris.brezillon@xxxxxxxxxxxxxxxxxx>
> ---
>  .../devicetree/bindings/mfd/atmel-lcdc.txt         | 75 ++++++++++++++++++++++
>  1 file changed, 75 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/mfd/atmel-lcdc.txt
> 
> diff --git a/Documentation/devicetree/bindings/mfd/atmel-lcdc.txt b/Documentation/devicetree/bindings/mfd/atmel-lcdc.txt
> new file mode 100644
> index 000000000000..70e9b7bda6c7
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/mfd/atmel-lcdc.txt
> @@ -0,0 +1,75 @@
> +Device-Tree bindings for Atmel's LCDC (LCD Controller) MFD driver
> +
> +Required properties:
> + - compatible: value should be one of the following:
> +   "atmel,at91sam9261-lcdc-mfd"
> +   "atmel,at91sam9263-lcdc-mfd"
> +   "atmel,at91sam9g10-lcdc-mfd"
> +   "atmel,at91sam9g45-lcdc-mfd"
> +   "atmel,at91sam9g46-lcdc-mfd"
> +   "atmel,at91sam9m10-lcdc-mfd"
> +   "atmel,at91sam9m11-lcdc-mfd"
> +   "atmel,at91sam9rl-lcdc-mfd"

I'm pretty sure we don't want the -mfd suffix in the compatible. I know
it's here to avoid clashes with the old binding, so maybe we can find
name.

> + - reg: base address and size of the LCDC device registers.
> + - clock-names: the name of the 2 clocks requested by the LCDC device.
> +   Should contain "lcdc_clk", and "hclk".
> + - clocks: should contain the 2 clocks requested by the LCDC device.
> +	   May specify the same clock twice is there is no need to enable
> +	   "hclk" to use the display.
> + - interrupts: should contain the description of the LCDC interrupt line
> +
> +The LCDC IP exposes two subdevices:
> + - a PWM chip: see ../pwm/atmel-lcdc-pwm.txt
> + - a Display Controller: see ../display/atmel/lcdc-display-controller.txt
> +
> +Example:
> +	lcdc0: lcdc@700000 {
> +		compatible = "atmel,at91sam9263-lcdc-mfd";
> +		reg = <0x700000 0x1000>;
> +		interrupts = <26 IRQ_TYPE_LEVEL_HIGH 3>;
> +		clocks = <&lcd_clk>, <&lcd_clk>;
> +		clock-names = "lcdc_clk", "hclk";
> +
> +		lcdc-display-controller {
> +			compatible = "atmel,lcdc-display-controller";
> +			lcd-supply = <&lcdc_reg>;
> +			#address-cells = <1>;
> +			#size-cells = <0>;
> +
> +			port@0 {
> +				reg = <0>;
> +				#address-cells = <1>;
> +				#size-cells = <0>;
> +				lcdc_panel_output: endpoint@0 {
> +					reg = <0>;
> +					remote-endpoint = <&panel_input>;
> +				};
> +			};
> +		};
> +
> +		lcdc_pwm: lcdc-pwm {
> +			compatible = "atmel,lcdc-pwm";
> +			pinctrl-names = "default";
> +			pinctrl-0 = <&pinctrl_lcdc_pwm>;
> +			#pwm-cells = <3>;
> +		};
> +
> +	};

Also, I don't remember why I decided to declare distinct nodes for the
PWM and display controller, but you should probably try to only declare
the lcdc node. Something like that:

	lcdc0: lcdc@700000 {
		compatible = "atmel,at91sam9263-lcdc";
		reg = <0x700000 0x1000>;
		interrupts = <26 IRQ_TYPE_LEVEL_HIGH 3>;
		clocks = <&lcd_clk>, <&lcd_clk>;
		clock-names = "lcdc_clk", "hclk";
		pinctrl-names = "default";
		pinctrl-0 = <&pinctrl_lcdc_pwm ...>;
		#pwm-cells = <3>;
		#address-cells = <1>;
		#size-cells = <0>;

		port@0 {
			reg = <0>;
			#address-cells = <1>;
			#size-cells = <0>;
			lcdc_panel_output: endpoint@0 {
				reg = <0>;
				remote-endpoint = <&panel_input>;
			};
		};
	};

Note that this representation does not prevent us from having an MFD
which declares the PWM and Display Engine, it's just that all devs will
point to the same of_node.

> +
> +		lcdc-display-controller {
> +			compatible = "atmel,lcdc-display-controller";
> +			lcd-supply = <&lcdc_reg>;

Hm, is this a regulator for the LCD controller or the LCD? If it's for
the LCD it should be placed under the panel node.

> +			#address-cells = <1>;
> +			#size-cells = <0>;
> +
> +			port@0 {
> +				reg = <0>;
> +				#address-cells = <1>;
> +				#size-cells = <0>;
> +				lcdc_panel_output: endpoint@0 {
> +					reg = <0>;
> +					remote-endpoint = <&panel_input>;
> +				};
> +			};
> +		};
> +
> +		lcdc_pwm: lcdc-pwm {
> +			compatible = "atmel,lcdc-pwm";
> +			pinctrl-names = "default";
> +			pinctrl-0 = <&pinctrl_lcdc_pwm>;
> +			#pwm-cells = <3>;
> +		};
> +
> +	};

> +
> +	panel: panel {
> +		compatible = "logictechnologies,lttd800480070-l2rt", "simple-panel";
> +		backlight = <&backlight>;
> +		power-supply = <&panel_reg>;
> +		#address-cells = <1>;
> +		#size-cells = <0>;
> +
> +		port@0 {
> +			#address-cells = <1>;
> +			#size-cells = <0>;
> +
> +			panel_input: endpoint@0 {
> +				reg = <0>;
> +				remote-endpoint = <&lcdc_panel_output>;
> +			};
> +		};
> +	};

_______________________________________________
dri-devel mailing list
dri-devel@xxxxxxxxxxxxxxxxxxxxx
https://lists.freedesktop.org/mailman/listinfo/dri-devel




[Index of Archives]     [Linux DRI Users]     [Linux Intel Graphics]     [Linux USB Devel]     [Video for Linux]     [Linux Audio Users]     [Yosemite News]     [Linux Kernel]     [Linux SCSI]     [XFree86]     [Linux USB Devel]     [Video for Linux]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [XFree86]
  Powered by Linux