On 27.06.2018 11:57, Sandeep Panda wrote: > Document the bindings used for the sn65dsi86 DSI to eDP bridge. > > Changes in v1: > - Rephrase the dt-binding descriptions to be more inline with existing > bindings (Andrzej Hajda). > - Add missing dt-binding that are parsed by corresponding driver > (Andrzej Hajda). > > Changes in v2: > - Remove edp panel specific dt-binding entries. Only keep bridge > specific entries (Sean Paul). > - Remove custom-modes dt entry since its usage is removed from driver also (Sean Paul). > - Remove is-pluggable dt entry since this will not be needed anymore (Sean Paul). > > Changes in v3: > - Remove irq-gpio dt entry and instead populate is an interrupt > property (Rob Herring). > > Changes in v4: > - Add link to bridge chip datasheet (Stephen Boyd) > - Add vpll and vcc regulator supply bindings (Stephen Boyd) > - Add ref clk optional dt binding (Stephen Boyd) > - Add gpio-controller optional dt binding (Stephen Boyd) > > Changes in v5: > - Use clock property to specify the input refclk (Stephen Boyd). > - Update gpio cell and pwm cell numbers (Stephen Boyd). > > Changes in v6: > - Add property to mention the lane mapping scheme and polarity inversion > (Stephen Boyd). > > Changes in v7: > - Detail description of lane mapping scheme dt property (Andrzej > Hajda/ Rob Herring). > - Removed HDP gpio binding, since the bridge uses IRQ signal to > determine HPD, and IRQ property is already documented in binding. > > Changes in v8: > - Removed unnecessary explanation of lane mapping and polarity dt > property, since these are already explained in media/video-interface > dt binidng (Rob Herring). > > Changes in v9: > - Avoid putting re-definition of lane mapping and polarity dt binding > (Rob Herring). > > Changes in v10: > - Use interrupts-extended property instead of interrupts to specify > interrupt line (Andrzej Hajda). > - Move data-lanes and lane-polarity property example to proper place (Andrzej Hajda). > > Changes in v11: > - Add a property for suspend gpio function of GPIO1 pin on bridge chip > (Stephen Boyd). > > Signed-off-by: Sandeep Panda <spanda@xxxxxxxxxxxxxx> > --- > .../bindings/display/bridge/ti,sn65dsi86.txt | 89 ++++++++++++++++++++++ > 1 file changed, 89 insertions(+) > create mode 100644 Documentation/devicetree/bindings/display/bridge/ti,sn65dsi86.txt > > diff --git a/Documentation/devicetree/bindings/display/bridge/ti,sn65dsi86.txt b/Documentation/devicetree/bindings/display/bridge/ti,sn65dsi86.txt > new file mode 100644 > index 000000000000..6787f5f2c7cd > --- /dev/null > +++ b/Documentation/devicetree/bindings/display/bridge/ti,sn65dsi86.txt > @@ -0,0 +1,89 @@ > +SN65DSI86 DSI to eDP bridge chip > +-------------------------------- > + > +This is the binding for Texas Instruments SN65DSI86 bridge. > +http://www.ti.com/general/docs/lit/getliterature.tsp?genericPartNumber=sn65dsi86&fileType=pdf > + > +Required properties: > +- compatible: Must be "ti,sn65dsi86" > +- reg: i2c address of the chip, 0x2d as per datasheet > +- enable-gpios: OF device-tree gpio specification for bridge_en pin (active high) > + > +- vccio-supply: A 1.8V supply that powers up the digital IOs. > +- vpll-supply: A 1.8V supply that powers up the displayport PLL. > +- vcca-supply: A 1.2V supply that powers up the analog circuits. > +- vcc-supply: A 1.2V supply that powers up the digital core. > + > +Optional properties: > +- interrupts-extended: Specifier for the SN65DSI86 interrupt line. > + > +- ddc-i2c-bus: phandle of the I2C controller used for DDC EDID probing One more thing, I have overlooked: why do you need this property? eDP panels passes its EDID via DP-AUX channel, do you have some strange panel? I have looked for the panel you want to add in this patchset - "Innolux TV123WAM" and found nothing, there is TV123WAM made by BOE (it is the same panel??) and it reports EDID via DP-AUX, no I2C lines for DDC. Regards Andrzej > + > +- gpio-controller: Marks the device has a GPIO controller. > +- #gpio-cells : Should be two. The first cell is the pin number and > + the second cell is used to specify flags. > + See ../../gpio/gpio.txt for more information. > +- #pwm-cells : Should be one. See ../../pwm/pwm.txt for description of > + the cell formats. > + > +- clock-names: should be "refclk" > +- clocks: Specification for input reference clock. The reference > + clock rate must be 12 MHz, 19.2 MHz, 26 MHz, 27 MHz or 38.4 MHz. > + > +- data-lanes: See ../../media/video-interface.txt > +- lane-polarities: See ../../media/video-interface.txt > + > +- suspend-gpios: OF device-tree specification for GPIO1 pin on bridge (active low) > + > +Required nodes: > +This device has two video ports. Their connections are modelled using the > +OF graph bindings specified in Documentation/devicetree/bindings/graph.txt. > + > +- Video port 0 for DSI input > +- Video port 1 for eDP output > + > +Example > +------- > + > +edp-bridge@2d { > + compatible = "ti,sn65dsi86"; > + #address-cells = <1>; > + #size-cells = <0>; > + reg = <0x2d>; > + > + enable-gpios = <&msmgpio 33 GPIO_ACTIVE_HIGH>; > + suspend-gpios = <&msmgpio 34 GPIO_ACTIVE_LOW>; > + > + interrupts-extended = <&gpio3 4 IRQ_TYPE_EDGE_FALLING>; > + > + vccio-supply = <&pm8916_l17>; > + vcca-supply = <&pm8916_l6>; > + vpll-supply = <&pm8916_l17>; > + vcc-supply = <&pm8916_l6>; > + > + clock-names = "refclk"; > + clocks = <&input_refclk>; > + > + ports { > + #address-cells = <1>; > + #size-cells = <0>; > + > + port@0 { > + reg = <0>; > + > + edp_bridge_in: endpoint { > + remote-endpoint = <&dsi_out>; > + }; > + }; > + > + port@1 { > + reg = <1>; > + > + edp_bridge_out: endpoint { > + data-lanes = <2 1 3 0>; > + lane-polarities = <0 1 0 1>; > + remote-endpoint = <&edp_panel_in>; > + }; > + }; > + }; > +} _______________________________________________ dri-devel mailing list dri-devel@xxxxxxxxxxxxxxxxxxxxx https://lists.freedesktop.org/mailman/listinfo/dri-devel
