On Sat, Jun 16, 2018 at 1:33 AM, Jernej Škrabec <jernej.skrabec@xxxxxxxx> wrote:
> Dne petek, 15. junij 2018 ob 19:13:17 CEST je Chen-Yu Tsai napisal(a):
>> On Sat, Jun 16, 2018 at 12:41 AM, Jernej Škrabec
>>
>> <jernej.skrabec@xxxxxxxx> wrote:
>> > Hi,
>> >
>> > Dne petek, 15. junij 2018 ob 10:31:10 CEST je Maxime Ripard napisal(a):
>> >> Hi,
>> >>
>> >> On Tue, Jun 12, 2018 at 10:00:20PM +0200, Jernej Skrabec wrote:
>> >> > TV TCONs connected to TCON TOP have to enable additional gate in order
>> >> > to work.
>> >> >
>> >> > Add support for such TCONs.
>> >> >
>> >> > Signed-off-by: Jernej Skrabec <jernej.skrabec@xxxxxxxx>
>> >> > ---
>> >> >
>> >> > drivers/gpu/drm/sun4i/sun4i_tcon.c | 11 +++++++++++
>> >> > drivers/gpu/drm/sun4i/sun4i_tcon.h | 4 ++++
>> >> > 2 files changed, 15 insertions(+)
>> >> >
>> >> > diff --git a/drivers/gpu/drm/sun4i/sun4i_tcon.c
>> >> > b/drivers/gpu/drm/sun4i/sun4i_tcon.c index 08747fc3ee71..0afb5a94a414
>> >> > 100644
>> >> > --- a/drivers/gpu/drm/sun4i/sun4i_tcon.c
>> >> > +++ b/drivers/gpu/drm/sun4i/sun4i_tcon.c
>> >> > @@ -688,6 +688,16 @@ static int sun4i_tcon_init_clocks(struct device
>> >> > *dev,
>> >> >
>> >> > dev_err(dev, "Couldn't get the TCON bus clock\n");
>> >> > return PTR_ERR(tcon->clk);
>> >> >
>> >> > }
>> >> >
>> >> > +
>> >> > + if (tcon->quirks->has_tcon_top_gate) {
>> >> > + tcon->top_clk = devm_clk_get(dev, "tcon-top");
>> >> > + if (IS_ERR(tcon->top_clk)) {
>> >> > + dev_err(dev, "Couldn't get the TCON TOP bus
>> >> > clock\n");
>> >> > + return PTR_ERR(tcon->top_clk);
>> >> > + }
>> >> > + clk_prepare_enable(tcon->top_clk);
>> >> > + }
>> >> > +
>> >>
>> >> Is it required for the TCON itself to operate, or does the TCON
>> >> requires the TCON TOP, which in turn requires that clock to be
>> >> functional?
>> >>
>> >> I find it quite odd to have a clock that isn't meant for a particular
>> >> device to actually be wired to another device. I'm not saying this
>> >> isn't the case, but it would be a first.
>> >
>> > Documentation doesn't say much about that gate. I did few tests and TCON
>> > registers can be read and written even if TCON TOP TV TCON gate is
>> > disabled. However, there is no image, as expected.
>>
>> The R40 manual does include it in the diagram, on page 504. There's also a
>> mux to select whether the clock comes directly from the CCU or the TV
>> encoder (a feedback mode?). I assume this is the gate you are referring to
>> here, in which case it is not a bus clock, but rather the TCON module or
>> channel clock, strangely routed.
>>
>> > More interestingly, I enabled test pattern directly in TCON to eliminate
>> > influence of the mixer. As soon as I disabled that gate, test pattern on
>> > HDMI screen was gone, which suggest that this gate influences something
>> > inside TCON.
>> >
>> > Another test I did was that I moved enable/disable gate code to
>> > sun4i_tcon_channel_set_status() and it worked just as well.
>> >
>> > I'll ask AW engineer what that gate actually does, but from what I saw, I
>> > would say that most appropriate location to enable/disable TCON TOP TV
>> > TCON
>> > gate is TCON driver. Alternatively, TCON TOP driver could check if any TV
>> > TCON is in use and enable appropriate gate. However, that doesn't sound
>> > right to me for some reason.
>>
>> If what I said above it true, then yes, the appropriate location to enable
>> it is the TCON driver, but moreover, the representation of the clock tree
>> should be fixed such that the TCON takes the clock from the TCON TOP as its
>> channel/ module clock instead. That way you don't need this patch, but
>> you'd add another for all the clock routing.
>
> Can you be more specific? I not sure what you mean here.
For clock related properties in the device tree:
&tcon_top {
clocks = <&ccu CLK_BUS_TCON_TOP>,
<&ccu CLK_TCON_TV0>,
<&tve0>,
<&ccu CLK_TCON_TV1>,
<&tve1>;
clock-names = "bus", "tcon-tv0", "tve0", "tcon-tv1", "tve1";
clock-output-names = "tcon-top-tv0", "tcon-top-tv1";
};
&tcon_tv0 {
clocks = <&ccu CLK_BUS_TCON_TV0>, <&tcon_top 0>'
clock-names = "ahb", "tcon-ch1";
};
A diagram would look like:
| This part is TCON TOP |
v v
CCU CLK_TCON_TV0 --|----\ |
| mux ---- gate ----|-- TCON_TV0
TVE0 --------------|----/ |
And the same goes for TCON_TV1 and TVE1.
The user manual is a bit lacking on how TVE outputs a clock though.
ChenYu
_______________________________________________
dri-devel mailing list
dri-devel@xxxxxxxxxxxxxxxxxxxxx
https://lists.freedesktop.org/mailman/listinfo/dri-devel
