Hi, Dne sreda, 13. junij 2018 ob 09:34:56 CEST je Maxime Ripard napisal(a): > Hi, > > Thanks for working on this! > > On Tue, Jun 12, 2018 at 10:00:13PM +0200, Jernej Skrabec wrote: > > TCON TOP main purpose is to configure whole display pipeline. It > > determines relationships between mixers and TCONs, selects source TCON > > for HDMI, muxes LCD and TV encoder GPIO output, selects TV encoder > > clock source and contains additional TV TCON and DSI gates. > > > > Signed-off-by: Jernej Skrabec <jernej.skrabec@xxxxxxxx> > > --- > > > > .../bindings/display/sunxi/sun4i-drm.txt | 45 +++++++++++++++++++ > > include/dt-bindings/clock/sun8i-tcon-top.h | 11 +++++ > > 2 files changed, 56 insertions(+) > > create mode 100644 include/dt-bindings/clock/sun8i-tcon-top.h > > > > diff --git a/Documentation/devicetree/bindings/display/sunxi/sun4i-drm.txt > > b/Documentation/devicetree/bindings/display/sunxi/sun4i-drm.txt index > > 3346c1e2a7a0..ef64c589a4b3 100644 > > --- a/Documentation/devicetree/bindings/display/sunxi/sun4i-drm.txt > > +++ b/Documentation/devicetree/bindings/display/sunxi/sun4i-drm.txt > > > > @@ -187,6 +187,51 @@ And on the A23, A31, A31s and A33, you need one more clock line: > > - 'lvds-alt': An alternative clock source, separate from the TCON > > channel 0 > > > > clock, that can be used to drive the LVDS clock > > > > +TCON TOP > > +-------- > > + > > +TCON TOPs main purpose is to configure whole display pipeline. It > > determines +relationships between mixers and TCONs, selects source TCON > > for HDMI, muxes +LCD and TV encoder GPIO output, selects TV encoder clock > > source and contains +additional TV TCON and DSI gates. > > + > > +It allows display pipeline to be configured in very different ways: > > + > > + / LCD0/LVDS0 > > + / TCON-LCD0 > > + | \ MIPI DSI > > + mixer0 | > > + \ / TCON-LCD1 - LCD1/LVDS1 > > + TCON-TOP > > + / \ TCON-TV0 - TVE0/RGB > > + mixer1 | \ > > + | TCON-TOP - HDMI > > + | / > > + \ TCON-TV1 - TVE1/RGB > > + > > +Note that both TCON TOP references same physical unit. > > + > > +Required properties: > > + - compatible: value must be one of: > > + * allwinner,sun8i-r40-tcon-top > > + - reg: base address and size of the memory-mapped region. > > + - clocks: phandle to the clocks feeding the TCON TOP > > + * bus: TCON TOP interface clock > > + - clock-names: clock name mentioned above > > + - resets: phandle to the reset line driving the DRC > > s/DRC/TCON TOP/ ? Yes, copy & paste issue > > > + * rst: TCON TOP reset line > > Remaining consistent with the clock name would be great You mean "ahb"? I noticed that most other nodes with reset lines don't have a name associated. Maybe I could just drop it and use first specified reset? > > > + - reset-names: reset name mentioned above > > + - #clock-cells : must contain 1 > > An example would be nice here You mean node example? with ports? In the past, Rob was against examples unless really necessary. Node from R40 DTSI can serve as an example. > > > +- ports: A ports node with endpoint definitions as defined in > > + Documentation/devicetree/bindings/media/video-interfaces.txt. The > > first port + should be the input for mixer0 mux. The second should be > > the output for that + mux. Third port should be input for mixer1 mux. > > Fourth port should be output + for mixer1 mux. Fifth port should be > > input for HDMI mux. Sixth port should + be output for it. All output > > endpoints should have reg property with the id + of the target TCON. > > All ports should have only one enpoint connected to > ^ endpoint > > I guess it would me more readable if you were to make it a bullet > list, but this works for me otherwise. Since I have to fix this patch anyway, I can refactor this text. Best regards, Jernej _______________________________________________ dri-devel mailing list dri-devel@xxxxxxxxxxxxxxxxxxxxx https://lists.freedesktop.org/mailman/listinfo/dri-devel
