On 30.05.2018 14:35, Laurent Pinchart wrote: > Hi Andrzej, > > On Wednesday, 30 May 2018 12:59:12 EEST Andrzej Hajda wrote: >> On 28.05.2018 12:18, Laurent Pinchart wrote: >>> On Monday, 28 May 2018 12:47:11 EEST Maciej Purski wrote: >>>> The patch adds bindings to Toshiba DSI/LVDS bridge TC358764. >>>> Bindings describe power supplies, reset gpio and video interfaces. >>>> >>>> Signed-off-by: Andrzej Hajda <a.hajda@xxxxxxxxxxx> >>>> Signed-off-by: Maciej Purski <m.purski@xxxxxxxxxxx> >>>> --- >>>> >>>> .../bindings/display/bridge/toshiba,tc358764.txt | 42 ++++++++++++++++ >>>> 1 file changed, 42 insertions(+) >>>> create mode 100644 >>>> >>>> Documentation/devicetree/bindings/display/bridge/toshiba,tc358764.txt >>>> >>>> diff --git >>>> a/Documentation/devicetree/bindings/display/bridge/toshiba,tc358764.txt >>>> b/Documentation/devicetree/bindings/display/bridge/toshiba,tc358764.txt >>>> new >>>> file mode 100644 >>>> index 0000000..d09bdc2 >>>> --- /dev/null >>>> +++ >>>> b/Documentation/devicetree/bindings/display/bridge/toshiba,tc358764.txt >>>> @@ -0,0 +1,42 @@ >>>> +TC358764 MIPI-DSI to LVDS panel bridge >>>> + >>>> +Required properties: >>>> + - compatible: "toshiba,tc358764" >>>> + - reg: the virtual channel number of a DSI peripheral >>>> + - vddc-supply: core voltage supply >>>> + - vddio-supply: I/O voltage supply >>>> + - vddmipi-supply: MIPI voltage supply >>>> + - vddlvds133-supply: LVDS1 3.3V voltage supply >>>> + - vddlvds112-supply: LVDS1 1.2V voltage supply >>> That's a lot of power supplies. Could some of them be merged together ? >>> See https://patchwork.freedesktop.org/patch/216058/ for an earlier >>> discussion on the same subject. >> Specs says about 3 supply voltage values: >> - 1.2V - digital core, DSI-RX PHY >> - 1.8-3.3V - digital I/O >> - 3.3V - LVDS-TX PHY >> >> So I guess it should be minimal number of supplies. Natural candidates: >> >> - vddc-supply: core voltage supply, 1.2V >> - vddio-supply: I/O voltage supply, 1.8V or 3.3V >> - vddlvds-supply: LVDS1/2 voltage supply, 3.3V >> >> I have changed name of the latest supply to be more consistent with >> other supplies, and changed 1.8-3.3 (which incorrectly suggest voltage >> range), to more precise voltage alternative. > This looks fine to me. > >>>> + - reset-gpios: a GPIO spec for the reset pin >>>> + >>>> +The device node can contain zero to two 'port' child nodes, each with >>>> one >>>> +child >>>> +'endpoint' node, according to the bindings defined in [1]. >>>> +The following are properties specific to those nodes. >>>> + >>>> +port: >>>> + - reg: (required) can be 0 for DSI port or 1 for LVDS port; >>> This seems pretty vague to me. It could be read as meaning that ports are >>> completely optional, and that the port number you list can be used, but >>> that something else could be used to. >>> >>> Let's make the port nodes mandatory. I propose the following. >>> >>> Required nodes: >>> >>> The TC358764 has DSI and LVDS ports whose connections are described using >>> the OF graph bindings defined in >>> Documentation/devicetree/bindings/graph.txt. The device node must contain >>> one 'port' child node per DSI and LVDS port. The port nodes are numbered >>> as follows. >>> >>> Port Number >>> ------------------------------------------------------------------- >>> DSI Input 0 >>> LVDS Output 1 >>> >>> Each port node must contain endpoint nodes describing the hardware >>> connections. >> Since the bridge is controlled via DSI bus, DSI input port is not necessary. > I don't agree with this. Regardless of how the bridge is controlled, I think > we should always use ports to describe the data connections. Otherwise it > would get more complicated for display controller drivers to use different > types of bridges. It was discussed already, and DT guideline is to skip graphs in simple case of parent/child nodes, see for example [1]. [1]: https://marc.info/?l=dri-devel&m=148354108702517&w=2 Regards Andrzej >>>> +[1]: Documentation/devicetree/bindings/media/video-interfaces.txt >>>> + >>>> +Example: >>>> + >>>> + bridge@0 { >>>> + reg = <0>; >>>> + compatible = "toshiba,tc358764"; >>>> + vddc-supply = <&vcc_1v2_reg>; >>>> + vddio-supply = <&vcc_1v8_reg>; >>>> + vddmipi-supply = <&vcc_1v2_reg>; >>>> + vddlvds133-supply = <&vcc_3v3_reg>; >>>> + vddlvds112-supply = <&vcc_1v2_reg>; >>>> + reset-gpios = <&gpd1 6 GPIO_ACTIVE_LOW>; >>>> + #address-cells = <1>; >>>> + #size-cells = <0>; >>>> + port@1 { >>>> + reg = <1>; >>>> + lvds_ep: endpoint { >>>> + remote-endpoint = <&panel_ep>; >>>> + }; >>>> + }; >>>> + }; _______________________________________________ dri-devel mailing list dri-devel@xxxxxxxxxxxxxxxxxxxxx https://lists.freedesktop.org/mailman/listinfo/dri-devel
