On 24.05.2018 18:41, Sandeep Panda wrote: > Document the bindings used for the sn65dsi86 DSI to eDP bridge. > > Changes in v1: > - Rephrase the dt-binding descriptions to be more inline with existing > bindings (Andrzej Hajda). > - Add missing dt-binding that are parsed by corresponding driver > (Andrzej Hajda). > > Changes in v2: > - Remove edp panel specific dt-binding entries. Only keep bridge > specific entries (Sean Paul). > - Remove custom-modes dt entry since its usage is removed from driver also (Sean Paul). > - Remove is-pluggable dt entry since this will not be needed anymore (Sean Paul). > > Changes in v3: > - Remove irq-gpio dt entry and instead populate is an interrupt > property (Rob Herring). > > Changes in v4: > - Add link to bridge chip datasheet (Stephen Boyd) > - Add vpll and vcc regulator supply bindings (Stephen Boyd) > - Add ref clk optional dt binding (Stephen Boyd) > - Add gpio-controller optional dt binding (Stephen Boyd) > > Changes in v5: > - Use clock property to specify the input refclk (Stephen Boyd). > - Update gpio cell and pwm cell numbers (Stephen Boyd). > > Changes in v6: > - Add property to mention the lane mapping scheme and polarity inversion > (Stephen Boyd). > > Signed-off-by: Sandeep Panda <spanda@xxxxxxxxxxxxxx> > --- > .../bindings/display/bridge/ti,sn65dsi86.txt | 89 ++++++++++++++++++++++ > 1 file changed, 89 insertions(+) > create mode 100644 Documentation/devicetree/bindings/display/bridge/ti,sn65dsi86.txt > > diff --git a/Documentation/devicetree/bindings/display/bridge/ti,sn65dsi86.txt b/Documentation/devicetree/bindings/display/bridge/ti,sn65dsi86.txt > new file mode 100644 > index 0000000..4a771a3 > --- /dev/null > +++ b/Documentation/devicetree/bindings/display/bridge/ti,sn65dsi86.txt > @@ -0,0 +1,89 @@ > +SN65DSI86 DSI to eDP bridge chip > +-------------------------------- > + > +This is the binding for Texas Instruments SN65DSI86 bridge. > +http://www.ti.com/general/docs/lit/getliterature.tsp?genericPartNumber=sn65dsi86&fileType=pdf > + > +Required properties: > +- compatible: Must be "ti,sn65dsi86" > +- reg: i2c address of the chip, 0x2d as per datasheet > +- enable-gpios: OF device-tree gpio specification for bridge_en pin info about active high should be added > + > +- vccio-supply: A 1.8V supply that powers up the digital IOs. > +- vpll-supply: A 1.8V supply that powers up the displayport PLL. > +- vcca-supply: A 1.2V supply that powers up the analog circuits. > +- vcc-supply: A 1.2V supply that powers up the digital core. > + > +Optional properties: > +- interrupts: Specifier for the SN65DSI86 interrupt line. > +- hpd-gpios: Specifications for HPD gpio pin. Again, please specify active level. > + > +- gpio-controller: Marks the device has a GPIO controller. > +- #gpio-cells : Should be two. The first cell is the pin number and > + the second cell is used to specify flags. > + See ../../gpio/gpio.txt for more information. > +- #pwm-cells : Should be one. See ../../pwm/pwm.txt for description of > + the cell formats. > + > +- clock-names: should be "refclk" > +- clocks: Specification for input reference clock. The reference > + clock rate must be 12 MHz, 19.2 MHz, 26 MHz, 27 MHz or 38.4 MHz. > + > +- lane-config: Specification to describe the logical to physical lane > + mapping scheme and polarity inversion of lanes. Please describe this property, I guess it is about DSI lanes, and it should be exact(?) four pair of numbers, what are meaning and ranges of both numbers. What should be assumed if property is not present. Btw you can look into other bindings for reference, I guess there are already bindings having such property. Regards Andrzej > + > +Required nodes: > + > +This device has two video ports. Their connections are modelled using the > +OF graph bindings specified in Documentation/devicetree/bindings/graph.txt. > + > +- Video port 0 for DSI input > +- Video port 1 for eDP output > + > +Example > +------- > + > +edp-bridge@2d { > + compatible = "ti,sn65dsi86"; > + #address-cells = <1>; > + #size-cells = <0>; > + reg = <0x2d>; > + > + enable-gpios = <&msmgpio 33 GPIO_ACTIVE_HIGH>; > + interrupt-parent = <&gpio3>; > + interrupts = <4 IRQ_TYPE_EDGE_FALLING>; > + > + vccio-supply = <&pm8916_l17>; > + vcca-supply = <&pm8916_l6>; > + vpll-supply = <&pm8916_l17>; > + vcc-supply = <&pm8916_l6>; > + > + clock-names = "refclk"; > + clocks = <&input_refclk>; > + > + lane-config = <0 0>, /* Lane 0 logical is lane 0 phys (!inv) */ > + <1 1>, /* Lane 1 logical is lane 1 phys (inv) */ > + <2 0>, /* Lane 2 logical is lane 2 phys (!inv) */ > + <3 1>; /* Lane 3 logical is lane 3 phys (inv) */ > + > + ports { > + #address-cells = <1>; > + #size-cells = <0>; > + > + port@0 { > + reg = <0>; > + > + edp_bridge_in: endpoint { > + remote-endpoint = <&dsi_out>; > + }; > + }; > + > + port@1 { > + reg = <1>; > + > + edp_bridge_out: endpoint { > + remote-endpoint = <&edp_panel_in>; > + }; > + }; > + }; > +} _______________________________________________ dri-devel mailing list dri-devel@xxxxxxxxxxxxxxxxxxxxx https://lists.freedesktop.org/mailman/listinfo/dri-devel
