On 2018-05-21 11:21, Andrzej Hajda wrote:
> On 21.05.2018 10:53, Peter Rosin wrote:
>> On 2018-05-21 10:15, Andrzej Hajda wrote:
>>> On 19.05.2018 18:48, Peter Rosin wrote:
>>>> On 2018-05-18 13:51, Andrzej Hajda wrote:
>>>>> On 26.04.2018 10:07, Jyri Sarha wrote:
>>>>>> Add device_link from panel device (supplier) to drm device (consumer)
>>>>>> when drm_panel_attach() is called. This patch should protect the
>>>>>> master drm driver if an attached panel driver unbinds while it is in
>>>>>> use. The device_link should make sure the drm device is unbound before
>>>>>> the panel driver becomes unavailable.
>>>>>>
>>>>>> The device_link is removed when drm_panel_detach() is called. The
>>>>>> drm_panel_detach() should be called by the consumer DRM driver, not the
>>>>>> panel driver, otherwise both drivers are racing to delete the same link.
>>>>>>
>>>>>> Signed-off-by: Jyri Sarha <jsarha@xxxxxx>
>>>>>> Reviewed-by: Eric Anholt <eric@xxxxxxxxxx>
>>>>> Hi Jyri,
>>>>>
>>>>> This patch breaks few platforms: tm2, tm2e, trats2 - ie all platforms
>>>>> using exynos_drm_dsi and dsi panels.
>>>>> Exynos-DSI properly handles panels unbind - ie references to panel are
>>>>> properly removed on panels removal and respective drm_connector enters
>>>>> disconnected state, without destroying whole drm device.
>>>>> And again on panel driver re-bind drm_panel is properly attached to
>>>>> exynos-dsi and panel pipeline is working again.
>>>>> This patch will break this behavior, ie it will destroy whole drm device.
>>>>>
>>>>> Making device_links for panels optional seems to me the best solution,
>>>>> what do you think?
>>>>>
>>>>> The funny thing is that due to bug in device link code, your patch has
>>>>> no effect on these platforms. So it does not hurt these platform yet,
>>>>> but the bug will be fixed sooner or later.
>>>> Ah, that's a pretty strong hint that we are doing something unusual. So,
>>>> I had a deeper look and I think that device-links (with state, i.e. not
>>>> DL_FLAG_STATELESS links) are assumed to be created by the .probe function
>>>> of either the consumer or the supplier. Then it seems to works as expected.
>>>> And that makes some sense too, because a link indicates that there exist
>>>> a dependency between the two and that the consumer cannot really exist
>>>> without the supplier. This is also what happens for the drm devices
>>>> (panel/bridge consumers) Jyri and I are working with; they call panel or
>>>> bridge attach during their probe. But this is not the case for exynos,
>>>> which calls panel/bridge attach at some later stage, and that obviously
>>>> violates the assumption that the device-link consumer cannot exist w/o
>>>> the supplier ("obviously" since the drm driver has managed to successfully
>>>> probe without the supplier).
>>>>
>>>> So, when the panel/bridge supplier is probed after the consumer is
>>>> bound, the link starts out as DL_STATE_DORMANT, and progresses to
>>>> DL_STATE_AVAILABLE once the panel/bridge has finished the probe. This is
>>>> not what *we* want.
>>> And this is also incorrect from Documentation PoV:
>>> * @DL_STATE_DORMANT: None of the supplier/consumer drivers is present.
>>> * @DL_STATE_AVAILABLE: The supplier driver is present, but the consumer
>>> is not.
>>>
>>>> So, one idea I have is to, on panel/bridge attach, verify if the
>>>> consumer is in its probe, and only create the link if that is the
>>>> case. So, the link would be optional, but it would all be automatic.
>>> Making it automatic looks tempting, but also error prone. In case of
>>> component framework bind callbacks can be called from probe of any
>>> component, so sometimes it can be called also from exynos-dsi probe,
>>> sometimes not (depending on order of probing, which we cannot rely on).
>>> So in some cases we will end-up with links, sometimes without. Ie
>>> following scenarios are possible in drm_panel_attach:
>>> 1. exynos-dsi bound, panel during probe.
>>> 2. exynos-dsi during probe, panel during probe.
>> 2. exynos-dsi during probe, panel bound? Or is this case 3, and 2 happens
>> when drivers probe in parallel?
>
> Panel is always probed not earlier than the end of exynos-dsi bind, so
> only scenarios 1 and 2 should be possible.
>
>> Whichever, you are right, I naively thought that the bind happened
>> after the probe of all devices, but naturally it happens as part of
>> the last device to register its component, and that normally happens
>> during its probe.
>>
>> Sigh. So, scratch that, I guess we need a flag...
I looked into that, and it seems very fragile to get the flag to be
correct for all cases. That road is bound to produce lots of bugs, and
it will be hard to get it right. In short, I would not descend into that
particular rabbit hole.
Can it be assumed that the drm_device of the encoder in drm_bridge_attach
is a master component, if the drm "cluster" is componentized? Are there
currently other ways of handling drm driver binding changes than
components?
If the answers are "yes" and "no", it might be possible to check if
encoder->dev is a master component and only establish the device link if
it isn't. All it would take is to add a component_device_is_master()
query function to drivers/base/component.c
Something like this (untested):
bool component_device_is_master(struct device *dev)
{
struct master *m;
mutex_lock(&component_mutex);
m = __master_find(dev, NULL);
mutex_unlock(&component_mutex);
return !!m;
}
EXPORT_SYMBOL_GPL(component_device_is_master);
And then check that before calling device_link_add().
Cheers,
Peter
_______________________________________________
dri-devel mailing list
dri-devel@xxxxxxxxxxxxxxxxxxxxx
https://lists.freedesktop.org/mailman/listinfo/dri-devel
