Re: [PATCH v2 3/4] drm/dsc: Define VESA Display Stream Compression Capabilities

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On 2018-05-14 10:05 PM, Manasi Navare wrote:
> From: Gaurav K Singh <gaurav.k.singh@xxxxxxxxx>
> 
> This defines all the DSC parameters as per the VESA DSC spec
> that will be required for DSC encoder/decoder
> 
> v2: Define this struct in DRM (From Manasi)
> * Changed the data types to u8/u16 instead of unsigned longs (Manasi)
> * Remove driver specific fields (Manasi)
> * Move this struct definition to DRM (Manasi)
> * Define DSC 1.2 parameters (Manasi)
> * Use DSC_NUM_BUF_RANGES (Manasi)
> * Call it drm_dsc_config (Manasi)
> 
> Cc: dri-devel@xxxxxxxxxxxxxxxxxxxxx
> Cc: Jani Nikula <jani.nikula@xxxxxxxxxxxxxxx>
> Cc: Ville Syrjala <ville.syrjala@xxxxxxxxxxxxxxx>
> Cc: Anusha Srivatsa <anusha.srivatsa@xxxxxxxxx>
> Signed-off-by: Manasi Navare <manasi.d.navare@xxxxxxxxx>
> Signed-off-by: Gaurav K Singh <gaurav.k.singh@xxxxxxxxx>
> ---
>  include/drm/drm_dsc.h | 111 ++++++++++++++++++++++++++++++++++++++++++++++++++
>  1 file changed, 111 insertions(+)
> 
> diff --git a/include/drm/drm_dsc.h b/include/drm/drm_dsc.h
> index 5ee72e8..04501e2 100644
> --- a/include/drm/drm_dsc.h
> +++ b/include/drm/drm_dsc.h
> @@ -30,6 +30,117 @@
>  
>  #define DSC_NUM_BUF_RANGES	15
>  
> +/* VESA Display Stream Compression DSC 1.2 constants */
> +#define DSC_NUM_BUF_RANGES		15

Duplicate definition of previous line.

Harry

> +
> +/* Configuration for a single Rate Control model range */
> +struct dsc_rc_range_parameters {
> +	/* Min Quantization Parameters allowed for this range */
> +	u8 range_min_qp;
> +	/* Max Quantization Parameters allowed for this range */
> +	u8 range_max_qp;
> +	/* Bits/group offset to apply to target for this group */
> +	u8 range_bpg_offset;
> +};
> +
> +struct drm_dsc_config {
> +	/* Bits / component for previous reconstructed line buffer */
> +	u8 line_buf_depth;
> +	/* Bits per component to code (must be 8, 10, or 12) */
> +	u8 bits_per_component;
> +	/*
> +	 * Flag indicating to do RGB - YCoCg conversion
> +	 * and back (should be 1 for RGB input)
> +	 */
> +	bool convert_rgb;
> +	u8 slice_count;
> +	/* Slice Width */
> +	u16 slice_width;
> +	/* Slice Height */
> +	u16 slice_height;
> +	/*
> +	 * 4:2:2 enable mode (from PPS, 4:2:2 conversion happens
> +	 * outside of DSC encode/decode algorithm)
> +	 */
> +	bool enable422;
> +	/* Picture Width */
> +	u16 pic_width;
> +	/* Picture Height */
> +	u16 pic_height;
> +	/* Offset to bits/group used by RC to determine QP adjustment */
> +	u8 rc_tgt_offset_high;
> +	/* Offset to bits/group used by RC to determine QP adjustment */
> +	u8 rc_tgt_offset_low;
> +	/* Bits/pixel target << 4 (ie., 4 fractional bits) */
> +	u16 bits_per_pixel;
> +	/*
> +	 * Factor to determine if an edge is present based
> +	 * on the bits produced
> +	 */
> +	u8 rc_edge_factor;
> +	/* Slow down incrementing once the range reaches this value */
> +	u8 rc_quant_incr_limit1;
> +	/* Slow down incrementing once the range reaches this value */
> +	u8 rc_quant_incr_limit0;
> +	/* Number of pixels to delay the initial transmission */
> +	u16 initial_xmit_delay;
> +	/* Number of pixels to delay the VLD on the decoder,not including SSM */
> +	u16  initial_dec_delay;
> +	/* Block prediction enable */
> +	bool block_pred_enable;
> +	/* Bits/group offset to use for first line of the slice */
> +	u8 first_line_bpg_offset;
> +	/* Value to use for RC model offset at slice start */
> +	u16 initial_offset;
> +	/* Thresholds defining each of the buffer ranges */
> +	u16 rc_buf_thresh[DSC_NUM_BUF_RANGES - 1];
> +	/* Parameters for each of the RC ranges */
> +	struct dsc_rc_range_parameters rc_range_params[DSC_NUM_BUF_RANGES];
> +	/* Total size of RC model */
> +	u16 rc_model_size;
> +	/* Minimum QP where flatness information is sent */
> +	u8 flatness_min_qp;
> +	/* Maximum QP where flatness information is sent */
> +	u8 flatness_max_qp;
> +	/* Initial value for scale factor */
> +	u8 initial_scale_value;
> +	/* Decrement scale factor every scale_decrement_interval groups */
> +	u16 scale_decrement_interval;
> +	/* Increment scale factor every scale_increment_interval groups */
> +	u16 scale_increment_interval;
> +	/* Non-first line BPG offset to use */
> +	u16 nfl_bpg_offset;
> +	/* BPG offset used to enforce slice bit */
> +	u16 slice_bpg_offset;
> +	/* Final RC linear transformation offset value */
> +	u16 final_offset;
> +	/* Enable on-off VBR (ie., disable stuffing bits) */
> +	bool vbr_enable;
> +	/* Mux word size (in bits) for SSM mode */
> +	u8 mux_word_size;
> +	/*
> +	 * The (max) size in bytes of the "chunks" that are
> +	 * used in slice multiplexing
> +	 */
> +	u16 slice_chunk_size;
> +	/* Rate Control buffer siz in bits */
> +	u16 rc_bits;
> +	/* DSC Minor Version */
> +	u8 dsc_version_minor;
> +	/* DSC Major version */
> +	u8 dsc_version_major;
> +	/* Native 4:2:2 support */
> +	bool native_422;
> +	/* Native 4:2:0 support */
> +	bool native_420;
> +	/* Additional bits/grp for seconnd line of slice for native 4:2:0 */
> +	u8 second_line_bpg_offset;
> +	/* Num of bits deallocated for each grp that is not in second line of slice */
> +	u16 nsl_bpg_offset;
> +	/* Offset adj fr second line in Native 4:2:0 mode */
> +	u16 second_line_offset_adj;
> +};
> +
>  /**
>   * struct picture_parameter_set - Represents 128 bytes of Picture Parameter Set
>   *
> 
_______________________________________________
dri-devel mailing list
dri-devel@xxxxxxxxxxxxxxxxxxxxx
https://lists.freedesktop.org/mailman/listinfo/dri-devel




[Index of Archives]     [Linux DRI Users]     [Linux Intel Graphics]     [Linux USB Devel]     [Video for Linux]     [Linux Audio Users]     [Yosemite News]     [Linux Kernel]     [Linux SCSI]     [XFree86]     [Linux USB Devel]     [Video for Linux]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [XFree86]
  Powered by Linux