On Monday, May 07, 2018 09:59 PM, Enric Balletbo Serra wrote:
Hi Lin, Thanks for the patch, apart from the new build warnings introduced some more comments below. 2018-05-04 10:08 GMT+02:00 Lin Huang <hl@xxxxxxxxxxxxxx>:the phy config values used to fix in dp firmware, but some boards need change these values to do training and get the better eye diagram result. So support that in phy driver. Signed-off-by: Chris Zhong <zyw@xxxxxxxxxxxxxx> Signed-off-by: Lin Huang <hl@xxxxxxxxxxxxxx> --- drivers/phy/rockchip/phy-rockchip-typec.c | 286 +++++++++++++++++++----------- include/soc/rockchip/rockchip_phy_typec.h | 72 ++++++++ 2 files changed, 259 insertions(+), 99 deletions(-) create mode 100644 include/soc/rockchip/rockchip_phy_typec.h diff --git a/drivers/phy/rockchip/phy-rockchip-typec.c b/drivers/phy/rockchip/phy-rockchip-typec.c index 76a4b58..831a93b 100644 --- a/drivers/phy/rockchip/phy-rockchip-typec.c +++ b/drivers/phy/rockchip/phy-rockchip-typec.c @@ -63,6 +63,7 @@ #include <linux/mfd/syscon.h> #include <linux/phy/phy.h> +#include <soc/rockchip/rockchip_phy_typec.h> #define CMN_SSM_BANDGAP (0x21 << 2) #define CMN_SSM_BIAS (0x22 << 2) @@ -323,23 +324,31 @@ * clock 0: PLL 0 div 1 * clock 1: PLL 1 div 2 */ -#define CLK_PLL_CONFIG 0X30 +#define CLK_PLL1_DIV1 0x20 +#define CLK_PLL1_DIV2 0x30 #define CLK_PLL_MASK 0x33 #define CMN_READY BIT(0) +#define DP_PLL_CLOCK_ENABLE_ACK BIT(3) #define DP_PLL_CLOCK_ENABLE BIT(2) +#define DP_PLL_ENABLE_ACK BIT(1) #define DP_PLL_ENABLE BIT(0) #define DP_PLL_DATA_RATE_RBR ((2 << 12) | (4 << 8)) #define DP_PLL_DATA_RATE_HBR ((2 << 12) | (4 << 8)) #define DP_PLL_DATA_RATE_HBR2 ((1 << 12) | (2 << 8)) +#define DP_PLL_DATA_RATE_MASK 0xff00 -#define DP_MODE_A0 BIT(4) -#define DP_MODE_A2 BIT(6) -#define DP_MODE_ENTER_A0 0xc101 -#define DP_MODE_ENTER_A2 0xc104 +#define DP_MODE_MASK 0xf +#define DP_MODE_ENTER_A0 BIT(0) +#define DP_MODE_ENTER_A2 BIT(2) +#define DP_MODE_ENTER_A3 BIT(3) +#define DP_MODE_A0_ACK BIT(4) +#define DP_MODE_A2_ACK BIT(6) +#define DP_MODE_A3_ACK BIT(7) +#define DP_LINK_RESET_DEASSERTED BIT(8) -#define PHY_MODE_SET_TIMEOUT 100000 +#define PHY_MODE_SET_TIMEOUT 1000000Why do you need to increase this timeout? Is because the software link training timed out using the old value?
That for debug, will fix it in next version.
#define PIN_ASSIGN_C_E 0x51d9 #define PIN_ASSIGN_D_F 0x5100 @@ -349,51 +358,7 @@ #define MODE_DFP_USB BIT(1) #define MODE_DFP_DP BIT(2) -struct usb3phy_reg { - u32 offset; - u32 enable_bit; - u32 write_enable; -}; - -/** - * struct rockchip_usb3phy_port_cfg: usb3-phy port configuration. - * @reg: the base address for usb3-phy config. - * @typec_conn_dir: the register of type-c connector direction. - * @usb3tousb2_en: the register of type-c force usb2 to usb2 enable. - * @external_psm: the register of type-c phy external psm clock. - * @pipe_status: the register of type-c phy pipe status. - * @usb3_host_disable: the register of type-c usb3 host disable. - * @usb3_host_port: the register of type-c usb3 host port. - * @uphy_dp_sel: the register of type-c phy DP select control. - */ -struct rockchip_usb3phy_port_cfg { - unsigned int reg; - struct usb3phy_reg typec_conn_dir; - struct usb3phy_reg usb3tousb2_en; - struct usb3phy_reg external_psm; - struct usb3phy_reg pipe_status; - struct usb3phy_reg usb3_host_disable; - struct usb3phy_reg usb3_host_port; - struct usb3phy_reg uphy_dp_sel; -}; - -struct rockchip_typec_phy { - struct device *dev; - void __iomem *base; - struct extcon_dev *extcon; - struct regmap *grf_regs; - struct clk *clk_core; - struct clk *clk_ref; - struct reset_control *uphy_rst; - struct reset_control *pipe_rst; - struct reset_control *tcphy_rst; - const struct rockchip_usb3phy_port_cfg *port_cfgs; - /* mutex to protect access to individual PHYs */ - struct mutex lock; - - bool flip; - u8 mode; -}; +#define DEFAULT_RATE 162000DEFAULT_RATE seems a very common name for me, maybe add a prefix?
Okay, will fix it.
struct phy_reg { u16 value; @@ -417,15 +382,15 @@ struct phy_reg usb3_pll_cfg[] = { { 0x8, CMN_DIAG_PLL0_LF_PROG }, }; -struct phy_reg dp_pll_cfg[] = { +struct phy_reg dp_pll_rbr_cfg[] = { { 0xf0, CMN_PLL1_VCOCAL_INIT }, { 0x18, CMN_PLL1_VCOCAL_ITER }, { 0x30b9, CMN_PLL1_VCOCAL_START }, - { 0x21c, CMN_PLL1_INTDIV }, + { 0x87, CMN_PLL1_INTDIV }, { 0, CMN_PLL1_FRACDIV }, - { 0x5, CMN_PLL1_HIGH_THR }, - { 0x35, CMN_PLL1_SS_CTRL1 }, - { 0x7f1e, CMN_PLL1_SS_CTRL2 }, + { 0x22, CMN_PLL1_HIGH_THR }, + { 0x8000, CMN_PLL1_SS_CTRL1 }, + { 0, CMN_PLL1_SS_CTRL2 }, { 0x20, CMN_PLL1_DSM_DIAG }, { 0, CMN_PLLSM1_USER_DEF_CTRL }, { 0, CMN_DIAG_PLL1_OVRD }, @@ -436,9 +401,52 @@ struct phy_reg dp_pll_cfg[] = { { 0x8, CMN_DIAG_PLL1_LF_PROG }, { 0x100, CMN_DIAG_PLL1_PTATIS_TUNE1 }, { 0x7, CMN_DIAG_PLL1_PTATIS_TUNE2 }, - { 0x4, CMN_DIAG_PLL1_INCLK_CTRL }, + { 0x1, CMN_DIAG_PLL1_INCLK_CTRL }, +}; + +struct phy_reg dp_pll_hbr_cfg[] = { + { 0xf0, CMN_PLL1_VCOCAL_INIT }, + { 0x18, CMN_PLL1_VCOCAL_ITER }, + { 0x30b4, CMN_PLL1_VCOCAL_START }, + { 0xe1, CMN_PLL1_INTDIV }, + { 0, CMN_PLL1_FRACDIV }, + { 0x5, CMN_PLL1_HIGH_THR }, + { 0x8000, CMN_PLL1_SS_CTRL1 }, + { 0, CMN_PLL1_SS_CTRL2 }, + { 0x20, CMN_PLL1_DSM_DIAG }, + { 0x1000, CMN_PLLSM1_USER_DEF_CTRL }, + { 0, CMN_DIAG_PLL1_OVRD }, + { 0, CMN_DIAG_PLL1_FBH_OVRD }, + { 0, CMN_DIAG_PLL1_FBL_OVRD }, + { 0x7, CMN_DIAG_PLL1_V2I_TUNE }, + { 0x45, CMN_DIAG_PLL1_CP_TUNE }, + { 0x8, CMN_DIAG_PLL1_LF_PROG }, + { 0x1, CMN_DIAG_PLL1_PTATIS_TUNE1 }, + { 0x1, CMN_DIAG_PLL1_PTATIS_TUNE2 }, + { 0x1, CMN_DIAG_PLL1_INCLK_CTRL }, }; +struct phy_reg dp_pll_hbr2_cfg[] = { + { 0xf0, CMN_PLL1_VCOCAL_INIT }, + { 0x18, CMN_PLL1_VCOCAL_ITER }, + { 0x30b4, CMN_PLL1_VCOCAL_START }, + { 0xe1, CMN_PLL1_INTDIV }, + { 0, CMN_PLL1_FRACDIV }, + { 0x5, CMN_PLL1_HIGH_THR }, + { 0x8000, CMN_PLL1_SS_CTRL1 }, + { 0, CMN_PLL1_SS_CTRL2 }, + { 0x20, CMN_PLL1_DSM_DIAG }, + { 0x1000, CMN_PLLSM1_USER_DEF_CTRL }, + { 0, CMN_DIAG_PLL1_OVRD }, + { 0, CMN_DIAG_PLL1_FBH_OVRD }, + { 0, CMN_DIAG_PLL1_FBL_OVRD }, + { 0x7, CMN_DIAG_PLL1_V2I_TUNE }, + { 0x45, CMN_DIAG_PLL1_CP_TUNE }, + { 0x8, CMN_DIAG_PLL1_LF_PROG }, + { 0x1, CMN_DIAG_PLL1_PTATIS_TUNE1 }, + { 0x1, CMN_DIAG_PLL1_PTATIS_TUNE2 }, + { 0x1, CMN_DIAG_PLL1_INCLK_CTRL }, +}; static const struct rockchip_usb3phy_port_cfg rk3399_usb3phy_port_cfgs[] = { { .reg = 0xff7c0000, @@ -484,7 +492,7 @@ static void tcphy_cfg_24m(struct rockchip_typec_phy *tcphy) rdata = readl(tcphy->base + CMN_DIAG_HSCLK_SEL); rdata &= ~CLK_PLL_MASK; - rdata |= CLK_PLL_CONFIG; + rdata |= CLK_PLL1_DIV2; writel(rdata, tcphy->base + CMN_DIAG_HSCLK_SEL); } @@ -498,17 +506,44 @@ static void tcphy_cfg_usb3_pll(struct rockchip_typec_phy *tcphy) tcphy->base + usb3_pll_cfg[i].addr); } -static void tcphy_cfg_dp_pll(struct rockchip_typec_phy *tcphy) +static void tcphy_cfg_dp_pll(struct rockchip_typec_phy *tcphy, int link_rate) { - u32 i; + struct phy_reg *phy_cfg; + u32 clk_ctrl; + u32 i, cfg_size, hsclk_sel; + + hsclk_sel = readl(tcphy->base + CMN_DIAG_HSCLK_SEL); + hsclk_sel &= ~CLK_PLL_MASK; + + switch (link_rate) { + case 162000: + clk_ctrl = DP_PLL_DATA_RATE_RBR; + hsclk_sel |= CLK_PLL1_DIV2; + phy_cfg = dp_pll_rbr_cfg; + cfg_size = ARRAY_SIZE(dp_pll_rbr_cfg); + break; + case 270000: + clk_ctrl = DP_PLL_DATA_RATE_HBR; + hsclk_sel |= CLK_PLL1_DIV2; + phy_cfg = dp_pll_hbr_cfg; + cfg_size = ARRAY_SIZE(dp_pll_hbr_cfg); + break; + case 540000: + clk_ctrl = DP_PLL_DATA_RATE_HBR2; + hsclk_sel |= CLK_PLL1_DIV1; + phy_cfg = dp_pll_hbr2_cfg; + cfg_size = ARRAY_SIZE(dp_pll_hbr2_cfg); + break; + } + + clk_ctrl |= DP_PLL_CLOCK_ENABLE | DP_PLL_ENABLE; + writel(clk_ctrl, tcphy->base + DP_CLK_CTL); - /* set the default mode to RBR */ - writel(DP_PLL_CLOCK_ENABLE | DP_PLL_ENABLE | DP_PLL_DATA_RATE_RBR, - tcphy->base + DP_CLK_CTL); + writel(hsclk_sel, tcphy->base + CMN_DIAG_HSCLK_SEL); /* load the configuration of PLL1 */ - for (i = 0; i < ARRAY_SIZE(dp_pll_cfg); i++) - writel(dp_pll_cfg[i].value, tcphy->base + dp_pll_cfg[i].addr); + for (i = 0; i < cfg_size; i++) + writel(phy_cfg[i].value, tcphy->base + phy_cfg[i].addr); } static void tcphy_tx_usb3_cfg_lane(struct rockchip_typec_phy *tcphy, u32 lane) @@ -535,9 +570,10 @@ static void tcphy_rx_usb3_cfg_lane(struct rockchip_typec_phy *tcphy, u32 lane) writel(0xfb, tcphy->base + XCVR_DIAG_BIDI_CTRL(lane)); } -static void tcphy_dp_cfg_lane(struct rockchip_typec_phy *tcphy, u32 lane) +static void tcphy_dp_cfg_lane(struct rockchip_typec_phy *tcphy, int link_rate, + u8 swing, u8 pre_emp, u32 lane) { - u16 rdata; + u16 val;>From what I see you are only renaming rdata to val, there is any reason?
not reason, just rename a new variable :)
writel(0xbefc, tcphy->base + XCVR_PSM_RCTRL(lane)); writel(0x6799, tcphy->base + TX_PSC_A0(lane)); @@ -545,25 +581,31 @@ static void tcphy_dp_cfg_lane(struct rockchip_typec_phy *tcphy, u32 lane) writel(0x98, tcphy->base + TX_PSC_A2(lane)); writel(0x98, tcphy->base + TX_PSC_A3(lane)); - writel(0, tcphy->base + TX_TXCC_MGNFS_MULT_000(lane)); - writel(0, tcphy->base + TX_TXCC_MGNFS_MULT_001(lane)); - writel(0, tcphy->base + TX_TXCC_MGNFS_MULT_010(lane)); - writel(0, tcphy->base + TX_TXCC_MGNFS_MULT_011(lane)); - writel(0, tcphy->base + TX_TXCC_MGNFS_MULT_100(lane)); - writel(0, tcphy->base + TX_TXCC_MGNFS_MULT_101(lane)); - writel(0, tcphy->base + TX_TXCC_MGNFS_MULT_110(lane)); - writel(0, tcphy->base + TX_TXCC_MGNFS_MULT_111(lane)); - writel(0, tcphy->base + TX_TXCC_CPOST_MULT_10(lane)); - writel(0, tcphy->base + TX_TXCC_CPOST_MULT_01(lane)); - writel(0, tcphy->base + TX_TXCC_CPOST_MULT_00(lane)); - writel(0, tcphy->base + TX_TXCC_CPOST_MULT_11(lane)); - - writel(0x128, tcphy->base + TX_TXCC_CAL_SCLR_MULT(lane)); - writel(0x400, tcphy->base + TX_DIAG_TX_DRV(lane)); - - rdata = readl(tcphy->base + XCVR_DIAG_PLLDRC_CTRL(lane)); - rdata = (rdata & 0x8fff) | 0x6000; - writel(rdata, tcphy->base + XCVR_DIAG_PLLDRC_CTRL(lane)); + writel(tcphy->config[swing][pre_emp].swing, + tcphy->base + TX_TXCC_MGNFS_MULT_000(lane)); + writel(tcphy->config[swing][pre_emp].pe, + tcphy->base + TX_TXCC_CPOST_MULT_00(lane)); + + if (swing == 2 && pre_emp == 0 && link_rate != 540000) { + writel(0x700, tcphy->base + TX_DIAG_TX_DRV(lane)); + writel(0x13c, tcphy->base + TX_TXCC_CAL_SCLR_MULT(lane)); + } else { + writel(0x128, tcphy->base + TX_TXCC_CAL_SCLR_MULT(lane)); + writel(0x0400, tcphy->base + TX_DIAG_TX_DRV(lane)); + } + + val = readl(tcphy->base + XCVR_DIAG_PLLDRC_CTRL(lane)); + val = val & 0x8fff; + switch (link_rate) { + case 162000: + case 270000: + val |= (6 << 12); + break; + case 540000: + val |= (4 << 12); + break; + } + writel(val, tcphy->base + XCVR_DIAG_PLLDRC_CTRL(lane)); } static inline int property_enable(struct rockchip_typec_phy *tcphy, @@ -754,30 +796,33 @@ static int tcphy_phy_init(struct rockchip_typec_phy *tcphy, u8 mode) tcphy_cfg_24m(tcphy); if (mode == MODE_DFP_DP) { - tcphy_cfg_dp_pll(tcphy); + tcphy_cfg_dp_pll(tcphy, DEFAULT_RATE); for (i = 0; i < 4; i++) - tcphy_dp_cfg_lane(tcphy, i); + tcphy_dp_cfg_lane(tcphy, DEFAULT_RATE, 0, 0, i); writel(PIN_ASSIGN_C_E, tcphy->base + PMA_LANE_CFG); } else { tcphy_cfg_usb3_pll(tcphy); - tcphy_cfg_dp_pll(tcphy); + tcphy_cfg_dp_pll(tcphy, DEFAULT_RATE); if (tcphy->flip) { tcphy_tx_usb3_cfg_lane(tcphy, 3); tcphy_rx_usb3_cfg_lane(tcphy, 2); - tcphy_dp_cfg_lane(tcphy, 0); - tcphy_dp_cfg_lane(tcphy, 1); + tcphy_dp_cfg_lane(tcphy, DEFAULT_RATE, 0, 0, 0); + tcphy_dp_cfg_lane(tcphy, DEFAULT_RATE, 0, 0, 1); } else { tcphy_tx_usb3_cfg_lane(tcphy, 0); tcphy_rx_usb3_cfg_lane(tcphy, 1); - tcphy_dp_cfg_lane(tcphy, 2); - tcphy_dp_cfg_lane(tcphy, 3); + tcphy_dp_cfg_lane(tcphy, DEFAULT_RATE, 0, 0, 2); + tcphy_dp_cfg_lane(tcphy, DEFAULT_RATE, 0, 0, 3); } writel(PIN_ASSIGN_D_F, tcphy->base + PMA_LANE_CFG); } - writel(DP_MODE_ENTER_A2, tcphy->base + DP_MODE_CTL); + val = readl(tcphy->base + DP_MODE_CTL); + val &= ~DP_MODE_MASK; + val |= DP_MODE_ENTER_A2 | DP_LINK_RESET_DEASSERTED; + writel(val, tcphy->base + DP_MODE_CTL); reset_control_deassert(tcphy->uphy_rst); @@ -990,7 +1035,7 @@ static int rockchip_dp_phy_power_on(struct phy *phy) property_enable(tcphy, &cfg->uphy_dp_sel, 1); ret = readx_poll_timeout(readl, tcphy->base + DP_MODE_CTL, - val, val & DP_MODE_A2, 1000, + val, val & DP_MODE_A2_ACK, 1000, PHY_MODE_SET_TIMEOUT); if (ret < 0) { dev_err(tcphy->dev, "failed to wait TCPHY enter A2\n"); @@ -999,13 +1044,19 @@ static int rockchip_dp_phy_power_on(struct phy *phy) tcphy_dp_aux_calibration(tcphy); - writel(DP_MODE_ENTER_A0, tcphy->base + DP_MODE_CTL); + /* enter A0 mode */ + val = readl(tcphy->base + DP_MODE_CTL); + val &= ~DP_MODE_MASK; + val |= DP_MODE_ENTER_A0; + writel(val, tcphy->base + DP_MODE_CTL); ret = readx_poll_timeout(readl, tcphy->base + DP_MODE_CTL, - val, val & DP_MODE_A0, 1000, + val, val & DP_MODE_A0_ACK, 1000, PHY_MODE_SET_TIMEOUT); if (ret < 0) { - writel(DP_MODE_ENTER_A2, tcphy->base + DP_MODE_CTL); + val &= ~DP_MODE_MASK; + val |= DP_MODE_ENTER_A2; + writel(val, tcphy->base + DP_MODE_CTL); dev_err(tcphy->dev, "failed to wait TCPHY enter A0\n"); goto power_on_finish; } @@ -1023,6 +1074,7 @@ static int rockchip_dp_phy_power_on(struct phy *phy) static int rockchip_dp_phy_power_off(struct phy *phy) { struct rockchip_typec_phy *tcphy = phy_get_drvdata(phy); + u32 val; mutex_lock(&tcphy->lock); @@ -1031,7 +1083,10 @@ static int rockchip_dp_phy_power_off(struct phy *phy) tcphy->mode &= ~MODE_DFP_DP; - writel(DP_MODE_ENTER_A2, tcphy->base + DP_MODE_CTL); + val = readl(tcphy->base + DP_MODE_CTL); + val &= ~DP_MODE_MASK; + val |= DP_MODE_ENTER_A2; + writel(val, tcphy->base + DP_MODE_CTL); if (tcphy->mode == MODE_DISCONNECT) tcphy_phy_deinit(tcphy); @@ -1047,6 +1102,30 @@ static const struct phy_ops rockchip_dp_phy_ops = { .owner = THIS_MODULE, }; +static int type_c_dp_phy_config(struct phy *phy, int link_rate,s/type_c/typec/ to be coherent with the rest of the code.+ int lanes, u8 swing, u8 pre_emp) +{ + struct rockchip_typec_phy *tcphy = phy_get_drvdata(phy); + u8 i; + + tcphy_cfg_dp_pll(tcphy, link_rate); + + if (tcphy->mode == MODE_DFP_DP) { + for (i = 0; i < 4; i++) + tcphy_dp_cfg_lane(tcphy, link_rate, swing, pre_emp, i); + } else { + if (tcphy->flip) { + tcphy_dp_cfg_lane(tcphy, link_rate, swing, pre_emp, 0); + tcphy_dp_cfg_lane(tcphy, link_rate, swing, pre_emp, 1); + } else { + tcphy_dp_cfg_lane(tcphy, link_rate, swing, pre_emp, 2); + tcphy_dp_cfg_lane(tcphy, link_rate, swing, pre_emp, 3); + } + } + + return 0; +} + static int tcphy_parse_dt(struct rockchip_typec_phy *tcphy, struct device *dev) { @@ -1087,6 +1166,14 @@ static int tcphy_parse_dt(struct rockchip_typec_phy *tcphy, return PTR_ERR(tcphy->tcphy_rst); } + /* + * check if phy_config pass from dts, if yes, + * need to use this phy config to do software training later + */ + if (!of_property_read_u32_array(dev->of_node, "rockchip,phy_config", + (u32 *)tcphy->config, sizeof(tcphy->config) / sizeof(u32))) + tcphy->need_software_training = 1; + return 0; } @@ -1171,6 +1258,7 @@ static int rockchip_typec_phy_probe(struct platform_device *pdev) } } + tcphy->typec_phy_config = type_c_dp_phy_config;type_c_dp_phy_config -> typec_dp_phy_configpm_runtime_enable(dev); for_each_available_child_of_node(np, child_np) { diff --git a/include/soc/rockchip/rockchip_phy_typec.h b/include/soc/rockchip/rockchip_phy_typec.h new file mode 100644 index 0000000..e25840e --- /dev/null +++ b/include/soc/rockchip/rockchip_phy_typec.h @@ -0,0 +1,72 @@ +/*Add the SPDX License identifier ...+ * Copyright (c) 2018, Fuzhou Rockchip Electronics Co., Ltd + * Author: Lin Huang <hl@xxxxxxxxxxxxxx> + * + * This program is free software; you can redistribute it and/or modify it + * under the terms and conditions of the GNU General Public License, + * version 2, as published by the Free Software Foundation. + * + * This program is distributed in the hope it will be useful, but WITHOUT + * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or + * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for + * more details.... and remove the above notice.+ */ +#ifndef __SOC_ROCKCHIP_PHY_TYPEC_H +#define __SOC_ROCKCHIP_PHY_TYPEC_H + +Remove the extra new line.+struct usb3phy_reg { + u32 offset; + u32 enable_bit; + u32 write_enable; +}; + +/** + * struct rockchip_usb3phy_port_cfg: usb3-phy port configuration. + * @reg: the base address for usb3-phy config. + * @typec_conn_dir: the register of type-c connector direction. + * @usb3tousb2_en: the register of type-c force usb2 to usb2 enable. + * @external_psm: the register of type-c phy external psm clock. + * @pipe_status: the register of type-c phy pipe status. + * @usb3_host_disable: the register of type-c usb3 host disable. + * @usb3_host_port: the register of type-c usb3 host port. + * @uphy_dp_sel: the register of type-c phy DP select control. + */ +struct rockchip_usb3phy_port_cfg { + unsigned int reg; + struct usb3phy_reg typec_conn_dir; + struct usb3phy_reg usb3tousb2_en; + struct usb3phy_reg external_psm; + struct usb3phy_reg pipe_status; + struct usb3phy_reg usb3_host_disable; + struct usb3phy_reg usb3_host_port; + struct usb3phy_reg uphy_dp_sel; +}; + +struct phy_config { + int swing; + int pe; +}; + +struct rockchip_typec_phy { + struct device *dev; + void __iomem *base; + struct extcon_dev *extcon; + struct regmap *grf_regs; + struct clk *clk_core; + struct clk *clk_ref; + struct reset_control *uphy_rst; + struct reset_control *pipe_rst; + struct reset_control *tcphy_rst; + struct rockchip_usb3phy_port_cfg *port_cfgs; + /* mutex to protect access to individual PHYs */ + struct mutex lock; + struct phy_config config[3][4]; + u8 need_software_training; + bool flip; + u8 mode; + int (*typec_phy_config)(struct phy *phy, int link_rate, + int lanes, u8 swing, u8 pre_emp); +}; + +#endifBest regards, Enric-- 2.7.4 _______________________________________________ Linux-rockchip mailing list Linux-rockchip@xxxxxxxxxxxxxxxxxxx http://lists.infradead.org/mailman/listinfo/linux-rockchip_______________________________________________ Linux-rockchip mailing list Linux-rockchip@xxxxxxxxxxxxxxxxxxx http://lists.infradead.org/mailman/listinfo/linux-rockchip
_______________________________________________ dri-devel mailing list dri-devel@xxxxxxxxxxxxxxxxxxxxx https://lists.freedesktop.org/mailman/listinfo/dri-devel
