> -----Ursprüngliche Nachricht-----
> Von: Shawn Guo
> Gesendet: Samstag, 28. April 2018 05:13
> An: Türk, Jan
> Cc: Rob Herring; Mark Rutland; Thierry Reding; David Airlie; Sascha Hauer;
> Pengutronix Kernel Team; Fabio Estevam; Russell King;
> devicetree@xxxxxxxxxxxxxxx; linux-kernel@xxxxxxxxxxxxxxx; dri-
> devel@xxxxxxxxxxxxxxxxxxxxx; LinuxArmKernelMailingListe
> Betreff: Re: [PATCH v4 6/7] ARM: dts: Add support for emtrion emCON-MX6
> series
>
> On Fri, Apr 27, 2018 at 03:24:41PM +0200, jan.tuerk@xxxxxxxxxxx wrote:
> > From: Jan Tuerk <jan.tuerk@xxxxxxxxxxx>
> >
> > This patch adds support for the emtrion GmbH emCON-MX6 modules.
> > They are available with imx.6 Solo, Dual-Lite, Dual and Quad equipped
> > with Memory from 512MB to 2GB (configured by U-Boot).
> >
> > Our default developer-Kit ships with the Avari baseboard and the EDT
> > ETM0700G0BDH6 Display (imx6[q|dl]-emcon-avari).
> >
> > The devicetree is split into the common part providing all module
> > components and the basic support for all SoC versions
> > (imx6qdl-emcon.dtsi) and parts which are i.mx6 S|DL and D|Q relevant.
> > Finally the support for the avari baseboard in the developer-kit
> > configuration is provided by the emcon-avari dts files.
> >
> > Signed-off-by: Jan Tuerk <jan.tuerk@xxxxxxxxxxx>
> > ---
> > Changes for v4:
> > - re-arrange the Patch-series to match the DT-submitting-patches
> > - Additional patch for the Documentation of the new DT-bindings
> > - alphabetically sort the DT
> > - moved duplicated Avari baseboard code into separate common file.
> >
> > arch/arm/boot/dts/Makefile | 2 +
> > arch/arm/boot/dts/imx6dl-emcon-avari.dts | 17 +
> > arch/arm/boot/dts/imx6dl-emcon.dtsi | 28 +
> > arch/arm/boot/dts/imx6q-emcon-avari.dts | 17 +
> > arch/arm/boot/dts/imx6q-emcon.dtsi | 28 +
> > arch/arm/boot/dts/imx6qdl-emcon-avari.dtsi | 208 ++++++++
> > arch/arm/boot/dts/imx6qdl-emcon.dtsi | 826
> +++++++++++++++++++++++++++++
> > 7 files changed, 1126 insertions(+)
> > create mode 100644 arch/arm/boot/dts/imx6dl-emcon-avari.dts
> > create mode 100644 arch/arm/boot/dts/imx6dl-emcon.dtsi
> > create mode 100644 arch/arm/boot/dts/imx6q-emcon-avari.dts
> > create mode 100644 arch/arm/boot/dts/imx6q-emcon.dtsi
> > create mode 100644 arch/arm/boot/dts/imx6qdl-emcon-avari.dtsi
> > create mode 100644 arch/arm/boot/dts/imx6qdl-emcon.dtsi
> >
> > diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
> > index 7e2424957809..05b930da3fda 100644
> > --- a/arch/arm/boot/dts/Makefile
> > +++ b/arch/arm/boot/dts/Makefile
> > @@ -381,6 +381,7 @@ dtb-$(CONFIG_SOC_IMX6Q) += \
> > imx6dl-cubox-i-emmc-som-v15.dtb \
> > imx6dl-cubox-i-som-v15.dtb \
> > imx6dl-dfi-fs700-m60.dtb \
> > + imx6dl-emcon-avari.dtb \
> > imx6dl-gw51xx.dtb \
> > imx6dl-gw52xx.dtb \
> > imx6dl-gw53xx.dtb \
> > @@ -442,6 +443,7 @@ dtb-$(CONFIG_SOC_IMX6Q) += \
> > imx6q-display5-tianma-tm070-1280x768.dtb \
> > imx6q-dmo-edmqmx6.dtb \
> > imx6q-dms-ba16.dtb \
> > + imx6q-emcon-avari.dtb \
> > imx6q-evi.dtb \
> > imx6q-gk802.dtb \
> > imx6q-gw51xx.dtb \
> > diff --git a/arch/arm/boot/dts/imx6dl-emcon-avari.dts
> > b/arch/arm/boot/dts/imx6dl-emcon-avari.dts
> > new file mode 100644
> > index 000000000000..464c82a53da3
> > --- /dev/null
> > +++ b/arch/arm/boot/dts/imx6dl-emcon-avari.dts
> > @@ -0,0 +1,17 @@
> > +// SPDX-License-Identifier: (GPL-2.0 or MIT)
> > +/*
> > + * Copyright (C) 2018 emtrion GmbH
> > + * Author: Jan Tuerk <jan.tuerk@xxxxxxxxxxx> */
> > +
> > +/dts-v1/;
> > +#include "imx6dl.dtsi"
> > +#include "imx6qdl-emcon.dtsi"
> > +/*Include camera2 pinmux*/
> > +#include "imx6dl-emcon.dtsi"
> > +#include "imx6qdl-emcon-avari.dtsi"
> > +
> > +/ {
> > + model = "emtrion SoM emCON-MX6 Solo/Dual-Lite Avari";
> > + compatible = "emtrion,emcon-mx6-avari", "fsl,imx6dl"; };
> > diff --git a/arch/arm/boot/dts/imx6dl-emcon.dtsi
> > b/arch/arm/boot/dts/imx6dl-emcon.dtsi
> > new file mode 100644
> > index 000000000000..0d86e0ecdb4d
> > --- /dev/null
> > +++ b/arch/arm/boot/dts/imx6dl-emcon.dtsi
> > @@ -0,0 +1,28 @@
> > +// SPDX-License-Identifier: (GPL-2.0 or MIT)
> > +/*
> > + * Copyright (C) 2018 emtrion GmbH
> > + * Author: Jan Tuerk <jan.tuerk@xxxxxxxxxxx> */
> > +
> > +/ {
> > + model = "emtrion SoM emCON-MX6 Solo/DualLite";
> > + compatible = "emtrion,emcon-mx6", "fsl,imx6dl"; };
> > +
> > +&iomuxc {
> > + pinctrl_cpi2: csi1grp {
> > + fsl,pins = <
> > + MX6QDL_PAD_EIM_D17__IPU1_CSI1_PIXCLK
> 0x0b0b1
> > + MX6QDL_PAD_EIM_EB3__IPU1_CSI1_HSYNC
> 0x1b0b1
> > + MX6QDL_PAD_EIM_D29__IPU1_CSI1_VSYNC
> 0x1b0b1
> > + MX6QDL_PAD_EIM_A17__IPU1_CSI1_DATA12
> 0x1b0b1
> > + MX6QDL_PAD_EIM_D27__IPU1_CSI1_DATA13
> 0x1b0b1
> > + MX6QDL_PAD_EIM_D26__IPU1_CSI1_DATA14
> 0x1b0b1
> > + MX6QDL_PAD_EIM_D20__IPU1_CSI1_DATA15
> 0x1b0b1
> > + MX6QDL_PAD_EIM_D19__IPU1_CSI1_DATA16
> 0x1b0b1
> > + MX6QDL_PAD_EIM_D18__IPU1_CSI1_DATA17
> 0x1b0b1
> > + MX6QDL_PAD_EIM_D16__IPU1_CSI1_DATA18
> 0x1b0b1
> > + MX6QDL_PAD_EIM_EB2__IPU1_CSI1_DATA19
> 0x1b0b1
> > + >;
> > + };
> > +};
>
> I'm uncomfortable with maintain two more dtsi files only for a single pinctrl
> entry. Instead, I would suggest you put CSI node and its pinctrl entry into
> imx6q/dl-emcon-avari.dts, and have CSI node refer to its pinctrl entry rather
> than having the pinctrl in hog group.
The origin Idea behind it is to prevent code duplication. For now there is only the avari baseboard which is upstreamed.
But for example, the Bvari [1] baseboard is upcoming and then we'll have code duplication for the csi node and their pincontrols.
Also I wanted a clean split between the processor module description (which is the emCON-MX6) and the baseboard (Avari),
to make it cleaner to integrate the module code with custom products (for example from our customers) without changing the File-layout over and over.
[1] https://www.emtrion.de/en/details_products-accessoires/bvari.html
>
> > diff --git a/arch/arm/boot/dts/imx6q-emcon-avari.dts
> > b/arch/arm/boot/dts/imx6q-emcon-avari.dts
> > new file mode 100644
> > index 000000000000..093afe2f9069
> > --- /dev/null
> > +++ b/arch/arm/boot/dts/imx6q-emcon-avari.dts
> > @@ -0,0 +1,17 @@
> > +// SPDX-License-Identifier: (GPL-2.0 or MIT)
> > +/*
> > + * Copyright (C) 2018 emtrion GmbH
> > + * Author: Jan Tuerk <jan.tuerk@xxxxxxxxxxx> */
> > +
> > +/dts-v1/;
> > +#include "imx6q.dtsi"
> > +#include "imx6qdl-emcon.dtsi"
> > +/*Include camera2 pinmux*/
> > +#include "imx6q-emcon.dtsi"
> > +#include "imx6qdl-emcon-avari.dtsi"
> > +
> > +/ {
> > + model = "emtrion SoM emCON-MX6 Dual/Quad on Avari";
> > + compatible = "emtrion,emcon-mx6-avari", "fsl,imx6q"; };
> > diff --git a/arch/arm/boot/dts/imx6q-emcon.dtsi
> > b/arch/arm/boot/dts/imx6q-emcon.dtsi
> > new file mode 100644
> > index 000000000000..bd7d2aa4248e
> > --- /dev/null
> > +++ b/arch/arm/boot/dts/imx6q-emcon.dtsi
> > @@ -0,0 +1,28 @@
> > +// SPDX-License-Identifier: (GPL-2.0 or MIT)
> > +/*
> > + * Copyright (C) 2018 emtrion GmbH
> > + * Author: Jan Tuerk <jan.tuerk@xxxxxxxxxxx> */
> > +
> > +/ {
> > + model = "emtrion SoM emCON-MX6 Dual/Quad";
> > + compatible = "emtrion,emcon-mx6", "fsl,imx6q"; };
> > +
> > +&iomuxc {
> > + pinctrl_cpi2: csi1grp {
> > + fsl,pins = <
> > + MX6QDL_PAD_EIM_D17__IPU2_CSI1_PIXCLK
> 0x0b0b1
> > + MX6QDL_PAD_EIM_EB3__IPU2_CSI1_HSYNC
> 0x1b0b1
> > + MX6QDL_PAD_EIM_D29__IPU2_CSI1_VSYNC
> 0x1b0b1
> > + MX6QDL_PAD_EIM_A17__IPU2_CSI1_DATA12
> 0x1b0b1
> > + MX6QDL_PAD_EIM_D27__IPU2_CSI1_DATA13
> 0x1b0b1
> > + MX6QDL_PAD_EIM_D26__IPU2_CSI1_DATA14
> 0x1b0b1
> > + MX6QDL_PAD_EIM_D20__IPU2_CSI1_DATA15
> 0x1b0b1
> > + MX6QDL_PAD_EIM_D19__IPU2_CSI1_DATA16
> 0x1b0b1
> > + MX6QDL_PAD_EIM_D18__IPU2_CSI1_DATA17
> 0x1b0b1
> > + MX6QDL_PAD_EIM_D16__IPU2_CSI1_DATA18
> 0x1b0b1
> > + MX6QDL_PAD_EIM_EB2__IPU2_CSI1_DATA19
> 0x1b0b1
> > + >;
> > + };
> > +};
> > diff --git a/arch/arm/boot/dts/imx6qdl-emcon-avari.dtsi
> > b/arch/arm/boot/dts/imx6qdl-emcon-avari.dtsi
> > new file mode 100644
> > index 000000000000..7fb870907ff8
> > --- /dev/null
> > +++ b/arch/arm/boot/dts/imx6qdl-emcon-avari.dtsi
> > @@ -0,0 +1,208 @@
> > +// SPDX-License-Identifier: (GPL-2.0 or MIT)
> > +/*
> > + * Copyright (C) 2018 emtrion GmbH
> > + * Author: Jan Tuerk <jan.tuerk@xxxxxxxxxxx> */
> > +
> > +/ {
> > + aliases {
> > + mmc0 = &usdhc3;
> > + mmc2 = &usdhc1;
> > + mmc1 = &usdhc2;
> > + mmc3 = &usdhc4;
> > + boardID = &boardID;
>
> Why do you need this boardID alias?
I wanted to have a generic entry point to address the board-id on all CPU-modules with their different SoC's resulting in different devicetree paths.
Also as it now has the generic "gpio@3a" name, there would be no other way in differencing the board Identifying GPIO-expander from an additionally
attached one (except platform code etc.)
With the alias every code could look up the information required over the alias path with the same piece of code.
>
> > + };
> > +
> > + chosen {
> > + stdout-path = <&uart1>;
> > + };
> > +
> > + memory@10000000 {
> > + reg = <0x10000000 0x40000000>;
> > + };
> > +
> > +
> > + reg_wall_5p0: reg_wall5p0 {
>
> For fixed regulators, please use regulator-xxx as node name.
OK
>
> > + compatible = "regulator-fixed";
> > + regulator-name = "Main-Supply";
> > + regulator-min-microvolt = <5000000>;
> > + regulator-max-microvolt = <5000000>;
> > + regulator-always-on;
> > + regulator-boot-on;
> > + };
> > +
> > + reg_base3p3: reg_base3p3 {
> > + compatible = "regulator-fixed";
> > + vin-supply = <®_wall_5p0>;
> > + regulator-name = "3V3-avari";
> > + regulator-min-microvolt = <3300000>;
> > + regulator-max-microvolt = <3300000>;
> > + regulator-always-on;
> > + regulator-boot-on;
> > + };
> > +
> > + reg_base1p5: reg_base1p5 {
> > + compatible = "regulator-fixed";
> > + vin-supply = <®_base3p3>;
> > + regulator-name = "1V5-avari";
> > + regulator-min-microvolt = <1500000>;
> > + regulator-max-microvolt = <1500000>;
> > + regulator-always-on;
> > + regulator-boot-on;
> > + };
> > +
> > + reg_usb_otg: reg_otg_vbus {
> > + compatible = "regulator-fixed";
> > + vin-supply = <®_wall_5p0>;
> > + regulator-name = "OTG_VBUS";
> > + regulator-min-microvolt = <5000000>;
> > + regulator-max-microvolt = <5000000>;
> > + gpio = <&gpio1 8 GPIO_ACTIVE_LOW>;
> > + regulator-always-on;
> > + };
> > +
> > +
> > + clk_codec: clock-codec {
> > + compatible = "fixed-clock";
> > + #clock-cells = <0>;
> > + clock-frequency = <12000000>;
> > + };
> > +
> > + sound {
> > + compatible = "fsl,imx-audio-sgtl5000";
> > + model = "emCON-avari-sgtl5000";
> > + ssi-controller = <&ssi2>;
> > + audio-codec = <&sgtl5000>;
> > + audio-routing =
> > + "Headphone Jack", "HP_OUT";
> > + mux-int-port = <2>;
> > + mux-ext-port = <3>;
> > + };
> > +};
> > +
> > +&iomuxc {
> > + pinctrl-names = "default";
> > + /*Unused emCON-MX6 pingroups on AVARI baseboard, enable
> defaults*/
> > + pinctrl-0 = <
> > + &pinctrl_emcon_gpio1 &pinctrl_emcon_gpio2
> > + &pinctrl_emcon_gpio3 &pinctrl_emcon_gpio5
> > + &pinctrl_emcon_gpio6 &pinctrl_emcon_gpio7
> > + &pinctrl_emcon_gpio8 &pinctrl_emcon_irq_a
> > + &pinctrl_emcon_irq_b &pinctrl_emcon_irq_c
> > + &pinctrl_emcon_irq_pwr
>
> Can these GPIO pins be put into one single pinctrl_emcon_gpio entry?
>From your point of view I agree, but our customers using the emCON module do not have
the schematics as I do, so they would have to create custom groups for every application the emCON-MX6[2] module is used for.
With those pinctrls defined, the modules dtsi much more generic to use for different baseboards and applications, IF they're used as specified on the connector.
Also the pinctrl_names are deferred from the Names on the Hardware Interface. For example &pinctrl_emcon_gpio5 is for the signal "GPIO_5" on the emCON connector.
Some of them are not even connected on the baseboard so they are in the Hog group, to force default settings for them.
[2] https://www.emtrion.de/en/details_products-accessoires/emcon-mx6-57.html
>
> > &pinctrl_nor_flash
> > + &pinctrl_usdhc2
> > + &pinctrl_spdif_out &pinctrl_spdif_in
> > + &pinctrl_cpi1 &pinctrl_cpi2
> > + >;
>
> Again, please do not put consumer device specific pins in hog group.
> Also, it's confusing to have the same pinctrl in both hog and consumer device
> node, like pinctrl_nor_flash and pinctrl_usdhc2 here.
About pinctrl_nor_flash I fully agree, that's a mistake.
pinctrl_usdhc2 is not connected on the avari, and therefore not enabled.
As told before it is added to the Hog group to force the default pinmuxing without enabling the hardware itself.
>
> > +};
> > +
> > +&audmux {
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pinctrl_audmux>;
> > + status = "okay";
> > +};
> > +
> > +&can1 {
> > + status = "okay";
> > +};
> > +
> > +&can2 {
> > + status = "okay";
> > +};
> > +
> > +&ecspi2 {
> > + status = "okay";
> > +};
> > +
> > +&hdmi {
> > + ddc-i2c-bus = <&i2c2>;
> > + status = "okay";
> > +};
> > +
> > +&i2c2 {
> > + status = "okay";
> > +};
> > +
> > +&i2c3 {
> > + clock-frequency = <100000>;
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pinctrl_i2c3>;
> > + status = "okay";
> > +
> > + sgtl5000: audio-codec@a {
> > + compatible = "fsl,sgtl5000";
> > + reg = <0x0a>;
> > + #sound-dai-cells = <0>;
> > + clocks = <&clk_codec>;
> > + VDDA-supply = <®_base3p3>;
> > + VDDIO-supply = <®_base3p3>;
> > + };
> > +
> > + boardID: gpio@3a {
> > + compatible = "nxp,pca8574";
> > + reg = <0x3a>;
> > + gpio-controller;
> > + #gpio-cells = <1>;
> > + };
> > +
> > + captouch: touchscreen@38 {
> > + compatible = "edt,edt-ft5406";
> > + reg = <0x38>;
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pinctrl_irq_touch2 &pinctrl_emcon_gpio4>;
> > + interrupt-parent = <&gpio6>;
> > + interrupts = <31 IRQ_TYPE_EDGE_FALLING>;
> > + wake-gpios = <&gpio2 3 GPIO_ACTIVE_HIGH>;
> > + wakeup-source;
> > + };
> > +};
> > +
> > +&pcie {
> > + status = "okay";
> > +};
> > +
> > +&rgb_encoder {
> > + status = "okay";
> > +};
> > +
> > +&rgb_panel {
> > + compatible = "edt,etm0700g0bdh6";
> > + status = "okay";
> > +};
> > +
> > +&ssi2 {
> > + status = "okay";
> > +};
> > +
> > +&uart2 {
> > + status = "okay";
> > + uart-has-rtscts;
> > +};
> > +
> > +&uart3 {
> > + status = "okay";
> > +};
> > +
> > +&uart4 {
> > + status = "okay";
> > +};
> > +
> > +&uart5 {
> > + status = "okay";
> > +};
> > +
> > +&usbh1 {
> > + status = "okay";
> > +};
> > +
> > +&usbotg {
> > + status = "okay";
> > +};
> > +
> > +&usdhc1 {
> > + status = "okay";
> > +};
> > +
> > +
> > +
> > +
>
> Remove these end of file newlines.
ack
>
> > diff --git a/arch/arm/boot/dts/imx6qdl-emcon.dtsi
> > b/arch/arm/boot/dts/imx6qdl-emcon.dtsi
> > new file mode 100644
> > index 000000000000..32b9bfdc3c41
> > --- /dev/null
> > +++ b/arch/arm/boot/dts/imx6qdl-emcon.dtsi
> > @@ -0,0 +1,826 @@
> > +// SPDX-License-Identifier: (GPL-2.0 or MIT)
> > +/*
> > + * Copyright (C) 2018 emtrion GmbH
> > + * Author: Jan Tuerk <jan.tuerk@xxxxxxxxxxx> */
> > +
> > +#include <dt-bindings/gpio/gpio.h>
> > +#include <dt-bindings/pwm/pwm.h>
> > +#include <dt-bindings/input/input.h>
> > +
> > +/ {
> > +
> > + model = "emtrion SoM emCON-MX6";
> > + compatible = "emtrion,emcon-mx6", "fsl,imx6q", "fsl,imx6dl";
> > +
> > + aliases {
> > + mmc0 = &usdhc3;
> > + mmc2 = &usdhc1;
> > + mmc1 = &usdhc2;
> > + };
> > +
> > + gpio-keys {
> > + compatible = "gpio-keys";
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pinctrl_emcon_wake>;
> > +
> > + wake {
> > + label = "Wake";
> > + linux,code = <KEY_WAKEUP>;
> > + gpios = <&gpio3 2 GPIO_ACTIVE_LOW>;
> > + wakeup-source;
> > + };
> > + };
> > +
> > + som_leds: leds {
> > + compatible = "gpio-leds";
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pinctrl_som_leds>;
> > +
> > + green {
> > + label = "som:green";
> > + gpios = <&gpio3 0 GPIO_ACTIVE_HIGH>;
> > + linux,default-trigger = "heartbeat";
> > + default-state = "on";
> > + };
> > +
> > + red {
> > + label = "som:red";
> > + gpios = <&gpio3 1 GPIO_ACTIVE_LOW>;
> > + default-state = "keep";
> > + };
> > +
> > + };
> > +
> > + lvds_backlight: lvds-backlight {
> > + compatible = "pwm-backlight";
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pinctrl_lvds_bl>;
> > + enable-gpios = <&gpio6 9 GPIO_ACTIVE_HIGH>;
> > + pwms = <&pwm1 0 50000>;
> > + brightness-levels = <
> > + 0 4 8 16 32 64 80 96 112
>
> One tab indent is good enough.
>
> > + 128 144 160 176 250
> > + >;
>
> Please align the close '>' with the beginning character of open '<'
> line, i.e. 'b'.
>
> > + default-brightness-level = <13>;
> > + status = "okay";
> > + };
>
> Have a newline between nodes.
Sorry.
>
> > + pwm_fan: pwm-fan {
> > + compatible = "pwm-fan";
> > + cooling-min-state = <0>;
> > + cooling-max-state = <4>;
> > + #cooling-cells = <2>;
> > + pwms = <&pwm4 0 50000>;
> > + cooling-levels = <0 64 127 191 255>;
> > + status = "disabled";
> > + };
> > +
> > +
> > + rgb_encoder: parallel-display {
>
> display for node name.
>
> > + compatible = "fsl,imx-parallel-display";
> > + #address-cells = <1>;
> > + #size-cells = <0>;
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pinctrl_rgb24_display>;
> > + status = "disabled";
> > +
> > + port@0 {
> > + reg = <0>;
> > +
> > + rgb_encoder_in: endpoint {
> > + remote-endpoint = <&ipu1_di0_disp0>;
> > + };
> > + };
> > +
> > + port@1 {
> > + reg = <1>;
> > +
> > + rgb_encoder_out: endpoint {
> > + remote-endpoint = <&rgb_panel_in>;
> > + };
> > + };
> > + };
> > +
> > + rgb_panel: panel {
>
> lcd for node name as suggested by Devicetree Specification?
I used the Kernel documentation as reference:
Documentation/devicetree/bindings/display/panel/simple-panel.txt-Example:
Documentation/devicetree/bindings/display/panel/simple-panel.txt-
Documentation/devicetree/bindings/display/panel/simple-panel.txt: panel: panel {
Documentation/devicetree/bindings/display/panel/simple-panel.txt- compatible = "cptt,claa101wb01";
Documentation/devicetree/bindings/display/panel/simple-panel.txt- ddc-i2c-bus = <&panelddc>;
Documentation/devicetree/bindings/display/panel/simple-panel.txt-
Same for a lot entries there...
sharp,ls037v7dw01.txt-lcd0: display {
samsung,s6e3ha2.txt- panel@0 {
sharp,lq101r1sx01.txt- panel: panel@0 {
etc. etc.
>
> > + backlight = <&rgb_backlight>;
> > + power-supply = <®_parallel_disp>;
> > +
> > + port {
> > + rgb_panel_in: endpoint {
> > + remote-endpoint = <&rgb_encoder_out>;
> > + };
> > + };
> > + };
> > +
> > + reg_parallel_disp: reg_parallel-display {
> > + compatible = "regulator-fixed";
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pinctrl_rgb_bl_en>;
> > + regulator-name = "LCD-Supply";
> > + regulator-min-microvolt = <5000000>;
> > + regulator-max-microvolt = <5000000>;
> > + gpio = <&gpio7 9 GPIO_ACTIVE_HIGH>;
> > + enable-active-high;
> > + };
> > +
> > + reg_lvds_disp: reg_lvds-display {
> > + compatible = "regulator-fixed";
> > + regulator-name = "LVDS-Supply";
> > + regulator-min-microvolt = <5000000>;
> > + regulator-max-microvolt = <5000000>;
> > + gpio = <&gpio7 10 GPIO_ACTIVE_HIGH>;
> > + enable-active-high;
> > + };
> > +
> > + rgb_backlight: rgb-backlight {
> > + compatible = "pwm-backlight";
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pinctrl_rgb_bl>;
> > + enable-gpios = <&gpio6 8 GPIO_ACTIVE_HIGH>;
> > + pwms = <&pwm3 0 5000000>;
> > + brightness-levels = <
> > + 250 176 160 144 128 112
> > + 96 80 64 48 32 16 8 1
> > + >;
> > + default-brightness-level = <13>;
> > + status = "okay";
> > + };
> > +};
> > +
> > +&can1 {
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pinctrl_can1>;
> > +};
> > +
> > +&can2 {
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pinctrl_can2>;
> > +};
> > +
> > +&ecspi2 {
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pinctrl_ecspi2>;
> > + cs-gpios = <&gpio2 25 GPIO_ACTIVE_HIGH>,
>
> One space after =.
>
> > + <&gpio2 26 GPIO_ACTIVE_HIGH>;
>
> Align the line with above one.
>
> > +};
> > +
> > +&ecspi4 {
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pinctrl_nor_flash>;
> > +};
> > +
> > +&fec {
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pinctrl_enet>;
> > + phy-mode = "rgmii";
> > + phy-reset-gpios = <&gpio5 20 GPIO_ACTIVE_LOW>;
> > + phy-reset-duration = <50>;
> > + phy-supply = <&vdd_1V8_reg>;
> > + phy-handle = <&ksz9031>;
> > + status = "okay";
> > +
> > +
>
> One newline.
>
> > + mdio {
> > + #address-cells = <1>;
> > + #size-cells = <0>;
> > +
> > + ksz9031: phy@0 {
> > + compatible = "ethernet-phy-ieee802.3-c22";
> > + reg = <0>;
> > + interrupt-parent = <&gpio1>;
> > + interrupts = <30 IRQ_TYPE_EDGE_FALLING>;
> > + rxdv-skew-ps = <480>;
> > + txen-skew-ps = <480>;
> > + rxd0-skew-ps = <480>;
> > + rxd1-skew-ps = <480>;
> > + rxd2-skew-ps = <480>;
> > + rxd3-skew-ps = <480>;
> > + txd0-skew-ps = <420>;
> > + txd1-skew-ps = <420>;
> > + txd2-skew-ps = <360>;
> > + txd3-skew-ps = <360>;
> > + txc-skew-ps = <1020>;
> > + rxc-skew-ps = <960>;
> > + };
> > + };
> > +};
> > +
> > +&i2c1 {
> > + clock-frequency = <100000>;
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pinctrl_i2c1>;
> > + status = "okay";
> > +
> > + rtc: rtc@68 {
>
> Is the label actually used? If yes, I would suggest a more specific name like
> ds1307.
Really? Why should it be a generic name for "gpio" and "pmic" but not a generic name for an "rtc" chip?
>
> > + compatible = "dallas,ds1307";
> > + reg = <0x68>;
> > + };
> > +
> > + da9063: pmic@58 {
> > + compatible = "dlg,da9063";
> > + reg = <0x58>;
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pinctrl_pmic>;
> > + interrupt-parent = <&gpio2>;
> > + interrupts = <8 IRQ_TYPE_LEVEL_LOW>;
> > + interrupt-controller;
> > +
> > + onkey {
> > + compatible = "dlg,da9063-onkey";
> > + wakeup-source;
> > + };
> > +
> > + wdt {
>
> s/wdt/watchdog. I remember I have already put this comment on previous
> version.
Yes , I do also remember, my fault sorry.
>
> > + compatible = "dlg,da9063-watchdog";
> > + timeout-sec = <0>;
> > + };
> > +
> > + regulators {
> > + vddcore_reg: bcore1 {
> > + regulator-min-microvolt = <1100000>;
> > + regulator-max-microvolt = <1450000>;
> > + regulator-ramp-delay = <20000>;
> > + regulator-name = "DA9063_CORE";
> > + regulator-always-on;
> > + };
> > +
> > + vddsoc_reg: bcore2 {
> > + regulator-min-microvolt = <1100000>;
> > + regulator-max-microvolt = <1450000>;
> > + regulator-ramp-delay = <20000>;
> > + regulator-name = "DA9063_SOC";
> > + regulator-always-on;
> > + };
> > +
> > + vdd_ddr3_reg: bpro {
> > + regulator-min-microvolt = <1500000>;
> > + regulator-max-microvolt = <1500000>;
> > + regulator-ramp-delay = <20000>;
> > + regulator-always-on;
> > + };
> > +
> > + vdd_3v3_reg: bperi {
> > + regulator-min-microvolt = <3300000>;
> > + regulator-max-microvolt = <3300000>;
> > + regulator-ramp-delay = <20000>;
> > + regulator-always-on;
> > + };
> > +
> > + vdd_sata_reg: ldo3 {
> > + regulator-min-microvolt = <2500000>;
> > + regulator-max-microvolt = <2500000>;
> > + regulator-always-on;
> > + };
> > + vdd_mipi_reg: ldo4 {
> > + regulator-min-microvolt = <2500000>;
> > + regulator-max-microvolt = <2500000>;
> > + regulator-always-on;
> > + };
> > +
> > + vdd_mx6_snvs_reg: ldo5 {
> > + regulator-min-microvolt = <3300000>;
> > + regulator-max-microvolt = <3300000>;
> > + regulator-always-on;
> > + };
> > +
> > + vdd_hdmi_reg: ldo6 {
> > + regulator-min-microvolt = <2500000>;
> > + regulator-max-microvolt = <2500000>;
> > + regulator-always-on;
> > + regulator-boot-on;
> > + };
> > +
> > + vdd_pcie_reg: ldo7 {
> > + regulator-min-microvolt = <2500000>;
> > + regulator-max-microvolt = <2500000>;
> > + regulator-always-on;
> > + };
> > +
> > + vdd_1V8_reg: ldo8 {
> > + regulator-min-microvolt = <1800000>;
> > + regulator-max-microvolt = <1800000>;
> > + regulator-always-on;
> > + };
> > +
> > + vdd_3V3_sdc_reg: ldo9 {
> > + regulator-min-microvolt = <1800000>;
> > + regulator-max-microvolt = <3300000>;
> > + regulator-always-on;
> > + };
> > +
> > + vdd_1V2_reg: ldo10 {
> > + regulator-min-microvolt = <1200000>;
> > + regulator-max-microvolt = <1200000>;
> > + regulator-always-on;
> > + };
> > + };
> > + };
> > +};
> > +
> > +&i2c2 {
> > + clock-frequency = <100000>;
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pinctrl_i2c2>;
> > +};
> > +
> > +&iomuxc {
> > +
> > + pinctrl_audmux: audmux {
>
> Please name the pinctrl node more consistently, maybe audmuxgrp to align
> with others?
I agree
>
> > + fsl,pins = <
> > + MX6QDL_PAD_CSI0_DAT7__AUD3_RXD
> 0x130b0
> > + MX6QDL_PAD_CSI0_DAT4__AUD3_TXC
> 0x1b060
> > + MX6QDL_PAD_CSI0_DAT5__AUD3_TXD
> 0x130B0
> > + MX6QDL_PAD_CSI0_DAT6__AUD3_TXFS
> 0x1b060
> > + >;
> > + };
> > +
> > + pinctrl_can1: can1grp {
> > + fsl,pins = <
> > + MX6QDL_PAD_KEY_COL2__FLEXCAN1_TX
> 0x1b0b1
> > + MX6QDL_PAD_KEY_ROW2__FLEXCAN1_RX
> 0x1b0b1
> > + >;
> > + };
> > +
> > + pinctrl_can2: can2grp {
> > + fsl,pins = <
> > + MX6QDL_PAD_KEY_COL4__FLEXCAN2_TX
> 0x1b0b1
> > + MX6QDL_PAD_KEY_ROW4__FLEXCAN2_RX
> 0x1b0b1
> > + >;
> > + };
> > +
> > + pinctrl_cpi1: csi0grp {
> > + fsl,pins = <
> > + MX6QDL_PAD_CSI0_PIXCLK__IPU1_CSI0_PIXCLK
> 0xb0b1
> > + MX6QDL_PAD_CSI0_MCLK__IPU1_CSI0_HSYNC
> 0x1b0b1
> > + MX6QDL_PAD_CSI0_VSYNC__IPU1_CSI0_VSYNC
> 0x1b0b1
> > + MX6QDL_PAD_CSI0_DAT12__IPU1_CSI0_DATA12
> 0x1b0b1
> > + MX6QDL_PAD_CSI0_DAT13__IPU1_CSI0_DATA13
> 0x1b0b1
> > + MX6QDL_PAD_CSI0_DAT14__IPU1_CSI0_DATA14
> 0x1b0b1
> > + MX6QDL_PAD_CSI0_DAT15__IPU1_CSI0_DATA15
> 0x1b0b1
> > + MX6QDL_PAD_CSI0_DAT16__IPU1_CSI0_DATA16
> 0x1b0b1
> > + MX6QDL_PAD_CSI0_DAT17__IPU1_CSI0_DATA17
> 0x1b0b1
> > + MX6QDL_PAD_CSI0_DAT18__IPU1_CSI0_DATA18
> 0x1b0b1
> > + MX6QDL_PAD_CSI0_DAT19__IPU1_CSI0_DATA19
> 0x1b0b1
> > + >;
> > + };
> > +
> > + /*camera2-pinctrl is in imx6q-emcon.dtsi or imx6dl-emcon.dtsi*/
> > +
> > + pinctrl_ecspi2: ecspi2grp {
> > + fsl,pins = <
> > + MX6QDL_PAD_EIM_CS0__ECSPI2_SCLK
> 0x100b1
> > + MX6QDL_PAD_EIM_CS1__ECSPI2_MOSI
> 0x100b1
> > + MX6QDL_PAD_EIM_OE__ECSPI2_MISO
> 0x100b1
> > + MX6QDL_PAD_EIM_LBA__GPIO2_IO27
> 0x100b1
> > + MX6QDL_PAD_EIM_RW__GPIO2_IO26
> 0x100b1
> > + >;
> > + };
> > +
> > + pinctrl_emcon_gpio1: emcongpio1 {
> > + fsl,pins = <
> > + MX6QDL_PAD_NANDF_D0__GPIO2_IO00
> 0x0b0b1
> > + >;
> > + };
> > +
> > + pinctrl_emcon_gpio2: emcongpio2 {
> > + fsl,pins = <
> > + MX6QDL_PAD_NANDF_D1__GPIO2_IO01
> 0x0b0b1
> > + >;
> > + };
> > +
> > + pinctrl_emcon_gpio3: emcongpio3 {
> > + fsl,pins = <
> > + MX6QDL_PAD_NANDF_D2__GPIO2_IO02
> 0x0b0b1
> > + >;
> > + };
> > +
> > + pinctrl_emcon_gpio4: emcongpio4 {
> > + fsl,pins = <
> > + MX6QDL_PAD_NANDF_D3__GPIO2_IO03
> 0x0b0b1
> > + >;
> > + };
> > +
> > + pinctrl_emcon_gpio5: emcongpio5 {
> > + fsl,pins = <
> > + MX6QDL_PAD_NANDF_D4__GPIO2_IO04
> 0x0b0b1
> > + >;
> > + };
> > +
> > + pinctrl_emcon_gpio6: emcongpio6 {
> > + fsl,pins = <
> > + MX6QDL_PAD_NANDF_D5__GPIO2_IO05
> 0x0b0b1
> > + >;
> > + };
> > +
> > + pinctrl_emcon_gpio7: emcongpio7 {
> > + fsl,pins = <
> > + MX6QDL_PAD_NANDF_D6__GPIO2_IO06
> 0x0b0b1
> > + >;
> > + };
> > +
> > + pinctrl_emcon_gpio8: emcongpio8 {
> > + fsl,pins = <
> > + MX6QDL_PAD_NANDF_D7__GPIO2_IO07
> 0x0b0b1
> > + >;
> > + };
> > +
> > + pinctrl_emcon_irq_a: emconirqa {
> > + fsl,pins = <
> > + MX6QDL_PAD_NANDF_CLE__GPIO6_IO07
> 0x0b0b1
> > + >;
> > + };
> > +
> > + pinctrl_emcon_irq_b: emconirqb {
> > + fsl,pins = <
> > + MX6QDL_PAD_NANDF_CS2__GPIO6_IO15
> 0x0b0b1
> > + >;
> > + };
> > +
> > + pinctrl_emcon_irq_c: emconirqc {
> > + fsl,pins = <
> > + MX6QDL_PAD_NANDF_CS3__GPIO6_IO16
> 0x0b0b1
> > + >;
> > + };
> > +
> > + pinctrl_emcon_irq_pwr: emconirqpwr {
> > + fsl,pins = <
> > + MX6QDL_PAD_EIM_D23__GPIO3_IO23
> 0x0b0b1
> > + >;
> > + };
> > +
> > + pinctrl_emcon_wake: emconwake {
> > + fsl,pins = <
> > + MX6QDL_PAD_EIM_DA2__GPIO3_IO02
> 0x1b0b1
> > + >;
> > + };
> > +
> > + pinctrl_enet: enetgrp {
> > + fsl,pins = <
> > + MX6QDL_PAD_ENET_MDIO__ENET_MDIO
> 0x1b030
> > + MX6QDL_PAD_ENET_MDC__ENET_MDC
> 0x1b030
> > + MX6QDL_PAD_RGMII_TXC__RGMII_TXC
> 0x1b030
> > + MX6QDL_PAD_RGMII_TD0__RGMII_TD0
> 0x1b030
> > + MX6QDL_PAD_RGMII_TD1__RGMII_TD1
> 0x1b030
> > + MX6QDL_PAD_RGMII_TD2__RGMII_TD2
> 0x1b030
> > + MX6QDL_PAD_RGMII_TD3__RGMII_TD3
> 0x1b030
> > + MX6QDL_PAD_RGMII_TX_CTL__RGMII_TX_CTL
> 0x1b030
> > + MX6QDL_PAD_ENET_REF_CLK__ENET_TX_CLK
> 0x4001a0b1
> > + MX6QDL_PAD_RGMII_RXC__RGMII_RXC
> 0x1b030
> > + MX6QDL_PAD_RGMII_RD0__RGMII_RD0
> 0x1b030
> > + MX6QDL_PAD_RGMII_RD1__RGMII_RD1
> 0x1b030
> > + MX6QDL_PAD_RGMII_RD2__RGMII_RD2
> 0x1b030
> > + MX6QDL_PAD_RGMII_RD3__RGMII_RD3
> 0x1b030
> > + MX6QDL_PAD_RGMII_RX_CTL__RGMII_RX_CTL
> 0x1b0b0
> > + MX6QDL_PAD_CSI0_DATA_EN__GPIO5_IO20
> 0x1b058
> > + MX6QDL_PAD_ENET_TXD0__GPIO1_IO30
> 0x1b0b0
> > + >;
> > + };
> > +
> > + pinctrl_i2c1: i2c1grp {
> > + fsl,pins = <
> > + MX6QDL_PAD_CSI0_DAT8__I2C1_SDA
> 0x4001b8b1
> > + MX6QDL_PAD_CSI0_DAT9__I2C1_SCL
> 0x4001b8b1
> > + >;
> > + };
> > +
> > + pinctrl_i2c2: i2c2grp {
> > + fsl,pins = <
> > + MX6QDL_PAD_KEY_COL3__I2C2_SCL
> 0x4001b8b1
> > + MX6QDL_PAD_KEY_ROW3__I2C2_SDA
> 0x4001b8b1
> > + >;
> > + };
> > +
> > + pinctrl_i2c3: i2c3grp {
> > + fsl,pins = <
> > + MX6QDL_PAD_GPIO_3__I2C3_SCL
> 0x4000b070
> > + MX6QDL_PAD_GPIO_6__I2C3_SDA
> 0x4001b870
> > + >;
> > + };
> > +
> > + pinctrl_irq_touch1: irqtouch1 {
> > + fsl,pins = <
> > + MX6QDL_PAD_GPIO_5__GPIO1_IO05
> 0x0b0b1
> > + >;
> > + };
>
> Unused?
Yes on the avari baseboard in the developer-kit configuration. But used when a LVDS Display is connected.
>
> > +
> > + pinctrl_irq_touch2: irqtouch2 {
> > + fsl,pins = <
> > + MX6QDL_PAD_EIM_BCLK__GPIO6_IO31
> 0x0b0b1
> > + >;
> > + };
> > +
> > + pinctrl_lvds_bl: lvdsbacklightgrp {
> > + fsl,pins = <
> > + MX6QDL_PAD_GPIO_9__PWM1_OUT
> 0x0b0b1
> > + MX6QDL_PAD_NANDF_WP_B__GPIO6_IO09
> 0x0b0b1
> > + >;
> > + };
> > +
> > + pinctrl_lvds_reg: lvdsreggrp {
> > + fsl,pins = <
> > + MX6QDL_PAD_SD4_CLK__GPIO7_IO10
> 0x0b0b1
> > + >;
> > + };
> > +
> > +
> > + pinctrl_nor_flash: norflashgrp {
> > + fsl,pins = <
> > + MX6QDL_PAD_NANDF_CS0__GPIO6_IO11
> 0x1b0b1
> > + MX6QDL_PAD_EIM_D21__ECSPI4_SCLK
> 0x100b1
> > + MX6QDL_PAD_EIM_D28__ECSPI4_MOSI
> 0x100b1
> > + MX6QDL_PAD_EIM_D22__ECSPI4_MISO
> 0x100b1
> > + MX6QDL_PAD_EIM_A25__GPIO5_IO02
> 0x100b1
> > + >;
> > + };
> > +
> > + pinctrl_pcie_ctrl: pciegrp {
> > + fsl,pins = <
> > + MX6QDL_PAD_EIM_A16__GPIO2_IO22
> 0x1b0b1
> > + MX6QDL_PAD_GPIO_17__GPIO7_IO12
> 0x1b0b1
> > + >;
> > + };
> > +
> > + pinctrl_pmic: pmicgrp {
> > + fsl,pins = <
> > + MX6QDL_PAD_SD4_DAT0__GPIO2_IO08
> 0x0b0b1
> > + >;
> > + };
> > +
> > + pinctrl_pwm_fan: pwmfan {
> > + fsl,pins = <
> > + MX6QDL_PAD_SD4_DAT2__PWM4_OUT
> 0x0b0b1
> > + >;
> > + };
> > +
> > + pinctrl_rgb_bl: rgbbacklightgrp {
> > + fsl,pins = <
> > + MX6QDL_PAD_SD4_DAT1__PWM3_OUT
> 0x0b0b1
> > + MX6QDL_PAD_NANDF_ALE__GPIO6_IO08
> 0x0b0b1
> > + >;
> > + };
> > +
> > + pinctrl_rgb_bl_en: rgbenable {
> > + fsl,pins = <
> > + MX6QDL_PAD_SD4_CMD__GPIO7_IO09
> 0x0b0b1
> > + >;
> > + };
> > +
> > + pinctrl_rgb24_display: rgbgrp {
> > + fsl,pins = <
> > + MX6QDL_PAD_DI0_DISP_CLK__IPU1_DI0_DISP_CLK
> 0x10
> > + MX6QDL_PAD_DI0_PIN15__IPU1_DI0_PIN15
> 0x10
> > + MX6QDL_PAD_DI0_PIN2__IPU1_DI0_PIN02 0x10
> > + MX6QDL_PAD_DI0_PIN3__IPU1_DI0_PIN03 0x10
> > + MX6QDL_PAD_DISP0_DAT0__IPU1_DISP0_DATA00
> 0x10
> > + MX6QDL_PAD_DISP0_DAT1__IPU1_DISP0_DATA01
> 0x10
> > + MX6QDL_PAD_DISP0_DAT2__IPU1_DISP0_DATA02
> 0x10
> > + MX6QDL_PAD_DISP0_DAT3__IPU1_DISP0_DATA03
> 0x10
> > + MX6QDL_PAD_DISP0_DAT4__IPU1_DISP0_DATA04
> 0x10
> > + MX6QDL_PAD_DISP0_DAT5__IPU1_DISP0_DATA05
> 0x10
> > + MX6QDL_PAD_DISP0_DAT6__IPU1_DISP0_DATA06
> 0x10
> > + MX6QDL_PAD_DISP0_DAT7__IPU1_DISP0_DATA07
> 0x10
> > + MX6QDL_PAD_DISP0_DAT8__IPU1_DISP0_DATA08
> 0x10
> > + MX6QDL_PAD_DISP0_DAT9__IPU1_DISP0_DATA09
> 0x10
> > + MX6QDL_PAD_DISP0_DAT10__IPU1_DISP0_DATA10
> 0x10
> > + MX6QDL_PAD_DISP0_DAT11__IPU1_DISP0_DATA11
> 0x10
> > + MX6QDL_PAD_DISP0_DAT12__IPU1_DISP0_DATA12
> 0x10
> > + MX6QDL_PAD_DISP0_DAT13__IPU1_DISP0_DATA13
> 0x10
> > + MX6QDL_PAD_DISP0_DAT14__IPU1_DISP0_DATA14
> 0x10
> > + MX6QDL_PAD_DISP0_DAT15__IPU1_DISP0_DATA15
> 0x10
> > + MX6QDL_PAD_DISP0_DAT16__IPU1_DISP0_DATA16
> 0x10
> > + MX6QDL_PAD_DISP0_DAT17__IPU1_DISP0_DATA17
> 0x10
> > + MX6QDL_PAD_DISP0_DAT18__IPU1_DISP0_DATA18
> 0x10
> > + MX6QDL_PAD_DISP0_DAT19__IPU1_DISP0_DATA19
> 0x10
> > + MX6QDL_PAD_DISP0_DAT20__IPU1_DISP0_DATA20
> 0x10
> > + MX6QDL_PAD_DISP0_DAT21__IPU1_DISP0_DATA21
> 0x10
> > + MX6QDL_PAD_DISP0_DAT22__IPU1_DISP0_DATA22
> 0x10
> > + MX6QDL_PAD_DISP0_DAT23__IPU1_DISP0_DATA23
> 0x10
> > + >;
> > + };
> > +
> > + pinctrl_secure: securegrp {
> > + fsl,pins = <
> > + MX6QDL_PAD_GPIO_18__GPIO7_IO13
> 0x1b0b1
> > + >;
> > + };
>
> Unused?
For now yes, but it describes the HW of the module.
>
> > +
> > + pinctrl_som_leds: somledgrp {
> > + fsl,pins = <
> > + MX6QDL_PAD_EIM_DA0__GPIO3_IO00
> 0x0b0b1
> > + MX6QDL_PAD_EIM_DA1__GPIO3_IO01
> 0x0b0b1
> > + >;
> > + };
> > +
> > + pinctrl_spdif_in: spdifin {
> > + fsl,pins = <
> > + MX6QDL_PAD_GPIO_16__SPDIF_IN
> 0x1b0b0
> > + >;
> > + };
> > +
> > + pinctrl_spdif_out: spdifout {
> > + fsl,pins = <
> > + MX6QDL_PAD_GPIO_19__SPDIF_OUT
> 0x13091
> > + >;
> > + };
> > +
> > + pinctrl_uart1: uart1grp {
> > + fsl,pins = <
> > + MX6QDL_PAD_CSI0_DAT10__UART1_TX_DATA
> 0x1b0b1
> > + MX6QDL_PAD_CSI0_DAT11__UART1_RX_DATA
> 0x1b0b1
> > + >;
> > + };
> > +
> > + pinctrl_uart2: uart2grp {
> > + fsl,pins = <
> > + MX6QDL_PAD_SD4_DAT5__UART2_RTS_B
> 0x1b0b1
> > + MX6QDL_PAD_SD4_DAT6__UART2_CTS_B
> 0x1b0b1
> > + MX6QDL_PAD_SD4_DAT7__UART2_TX_DATA
> 0x1b0b1
> > + MX6QDL_PAD_SD4_DAT4__UART2_RX_DATA
> 0x1b0b1
> > + >;
> > + };
> > +
> > + pinctrl_uart3: uart3grp {
> > + fsl,pins = <
> > + MX6QDL_PAD_EIM_D24__UART3_TX_DATA
> 0x1b0b1
> > + MX6QDL_PAD_EIM_D25__UART3_RX_DATA
> 0x1b0b1
> > + >;
> > + };
> > +
> > + pinctrl_uart4: uart4grp {
> > + fsl,pins = <
> > + MX6QDL_PAD_KEY_COL0__UART4_TX_DATA
> 0x1b0b1
> > + MX6QDL_PAD_KEY_ROW0__UART4_RX_DATA
> 0x1b0b1
> > + >;
> > + };
> > +
> > + pinctrl_uart5: uart5grp {
> > + fsl,pins = <
> > + MX6QDL_PAD_KEY_COL1__UART5_TX_DATA
> 0x1b0b1
> > + MX6QDL_PAD_KEY_ROW1__UART5_RX_DATA
> 0x1b0b1
> > + >;
> > + };
> > +
> > + pinctrl_usb_host1: usbhgrp {
> > + fsl,pins = <
> > + MX6QDL_PAD_EIM_D31__USB_H1_PWR
> 0x1B058
> > + MX6QDL_PAD_EIM_D30__USB_H1_OC
> 0x1B058
> > + >;
> > + };
> > +
> > + pinctrl_usb_otg: usbotggrp {
> > + fsl,pins = <
> > + MX6QDL_PAD_ENET_RX_ER__USB_OTG_ID
> 0x17059
> > + MX6QDL_PAD_GPIO_7__GPIO1_IO07
> 0x17059
> > + MX6QDL_PAD_GPIO_8__GPIO1_IO08
> 0x17059
> > + >;
> > + };
> > +
> > + pinctrl_usdhc1: usdhc1grp {
> > + fsl,pins = <
> > + MX6QDL_PAD_SD1_CMD__SD1_CMD
> 0x17059
> > + MX6QDL_PAD_SD1_CLK__SD1_CLK
> 0x10059
> > + MX6QDL_PAD_SD1_DAT0__SD1_DATA0
> 0x17059
> > + MX6QDL_PAD_SD1_DAT1__SD1_DATA1
> 0x17059
> > + MX6QDL_PAD_SD1_DAT2__SD1_DATA2
> 0x17059
> > + MX6QDL_PAD_SD1_DAT3__SD1_DATA3
> 0x17059
> > + MX6QDL_PAD_GPIO_1__SD1_CD_B
> 0x1b0b1
> > + MX6QDL_PAD_DI0_PIN4__SD1_WP
> 0x1b0b1
> > + >;
> > + };
> > +
> > + pinctrl_usdhc2: usdhc2grp {
> > + fsl,pins = <
> > + MX6QDL_PAD_SD2_CMD__SD2_CMD
> 0x17059
> > + MX6QDL_PAD_SD2_CLK__SD2_CLK
> 0x10059
> > + MX6QDL_PAD_SD2_DAT0__SD2_DATA0
> 0x17059
> > + MX6QDL_PAD_SD2_DAT1__SD2_DATA1
> 0x17059
> > + MX6QDL_PAD_SD2_DAT2__SD2_DATA2
> 0x17059
> > + MX6QDL_PAD_SD2_DAT3__SD2_DATA3
> 0x17059
> > + MX6QDL_PAD_GPIO_4__SD2_CD_B
> 0x1b0b1
> > + MX6QDL_PAD_GPIO_2__SD2_WP
> 0x1b0b1
> > + >;
> > + };
> > +
> > + pinctrl_usdhc3: usdhc3grp {
> > + fsl,pins = <
> > + MX6QDL_PAD_SD3_CMD__SD3_CMD
> 0x17059
> > + MX6QDL_PAD_SD3_CLK__SD3_CLK
> 0x10059
> > + MX6QDL_PAD_SD3_DAT0__SD3_DATA0
> 0x17059
> > + MX6QDL_PAD_SD3_DAT1__SD3_DATA1
> 0x17059
> > + MX6QDL_PAD_SD3_DAT2__SD3_DATA2
> 0x17059
> > + MX6QDL_PAD_SD3_DAT3__SD3_DATA3
> 0x17059
> > + MX6QDL_PAD_SD3_DAT4__SD3_DATA4
> 0x17059
> > + MX6QDL_PAD_SD3_DAT5__SD3_DATA5
> 0x17059
> > + MX6QDL_PAD_SD3_DAT6__SD3_DATA6
> 0x17059
> > + MX6QDL_PAD_SD3_DAT7__SD3_DATA7
> 0x17059
> > + MX6QDL_PAD_SD3_RST__SD3_RESET
> 0x1b0b1
> > + >;
> > + };
> > +};
> > +
> > +&ipu1_di0_disp0 {
> > + remote-endpoint = <&rgb_encoder_in>; };
> > +
> > +&pcie {
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pinctrl_pcie_ctrl>;
> > + reset-gpio = <&gpio7 12 GPIO_ACTIVE_LOW>;
> > + disable-gpio = <&gpio2 22 GPIO_ACTIVE_LOW>; };
> > +
> > +&pwm1 {
> > + status = "okay";
> > +};
> > +
> > +&pwm3 {
> > + status = "okay";
> > +};
> > +
> > +&pwm4 {
> > + status = "okay";
> > +};
> > +
> > +&uart1 {
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pinctrl_uart1>;
> > + status = "okay";
> > +};
> > +
> > +&uart2 {
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pinctrl_uart2>;
> > +};
> > +
> > +&uart3 {
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pinctrl_uart3>;
> > +};
> > +
> > +&uart4 {
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pinctrl_uart4>;
> > +};
> > +
> > +&uart5 {
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pinctrl_uart5>;
> > +};
> > +
> > +&usbh1 {
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pinctrl_usb_host1>;
> > +};
> > +
> > +&usbotg {
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pinctrl_usb_otg>;
> > + vbus-supply = <®_usb_otg>;
> > + dr_mode = "peripheral";
> > +};
> > +
> > +&usdhc1 {
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pinctrl_usdhc1>;
> > + fsl,wp-controller;
> > +};
> > +
> > +&usdhc2 {
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pinctrl_usdhc2>;
> > + fsl,wp-controller;
> > +};
> > +
> > +&usdhc3 {
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pinctrl_usdhc3>;
> > + non-removable;
> > + bus-width = <8>;
> > + status = "okay";
> > +};
> > +
> > +/******device power Management*********/
> > +
> > +&cpu0 {
> > + voltage-tolerance = <2>;
> > +};
> > +
> > +®_arm {
> > + vin-supply = <&vddcore_reg>;
> > +};
> > +
> > +®_soc {
> > + vin-supply = <&vddsoc_reg>;
> > +};
> > +
> > +®_pu {
> > + vin-supply = <&vddsoc_reg>;
> > +};
> > +
> > +
> > +
>
> One newline.
Ack
>
> Shawn
>
> > +/*******Disabled HW following***********/
> > +
> > +&snvs_rtc {
> > + status = "disabled";
> > +};
> > --
> > 2.11.0
> >
Jan
_______________________________________________
dri-devel mailing list
dri-devel@xxxxxxxxxxxxxxxxxxxxx
https://lists.freedesktop.org/mailman/listinfo/dri-devel
