Hi Archit,
On Sun, 15 Apr 2018 13:39:44 +0530
Archit Taneja <architt@xxxxxxxxxxxxxx> wrote:
> > +static int cdns_dsi_get_dphy_pll_cfg(struct cdns_dphy *dphy,
> > + struct cdns_dphy_cfg *cfg,
> > + unsigned int dpi_htotal,
> > + unsigned int dpi_bpp,
> > + unsigned int dpi_hz,
> > + unsigned int dsi_htotal,
> > + unsigned int dsi_nlanes,
> > + unsigned int *dsi_hfp_ext)
> > +{
> > + u64 dlane_bps, dlane_bps_max, fbdiv, fbdiv_max, adj_dsi_htotal;
> > + unsigned long pll_ref_hz = clk_get_rate(dphy->pll_ref_clk);
> > +
> > + memset(cfg, 0, sizeof(*cfg));
> > +
> > + cfg->nlanes = dsi_nlanes;
> > +
> > + if (pll_ref_hz < 9600000 || pll_ref_hz >= 150000000)
> > + return -EINVAL;
> > + else if (pll_ref_hz < 19200000)
> > + cfg->pll_ipdiv = 1;
> > + else if (pll_ref_hz < 38400000)
> > + cfg->pll_ipdiv = 2;
> > + else if (pll_ref_hz < 76800000)
> > + cfg->pll_ipdiv = 4;
> > + else
> > + cfg->pll_ipdiv = 8;
> > +
> > + /*
> > + * Make sure DSI htotal is aligned on a lane boundary when calculating
> > + * the expected data rate. This is done by extending HFP in case of
> > + * misalignment.
> > + */
> > + adj_dsi_htotal = dsi_htotal;
> > + if (dsi_htotal % dsi_nlanes)
> > + adj_dsi_htotal += dsi_nlanes - (dsi_htotal % dsi_nlanes);
> > +
> > + dlane_bps = (u64)dpi_hz * adj_dsi_htotal;
> > +
> > + /* data rate in bytes/sec is not an integer, refuse the mode. */
> > + if (do_div(dlane_bps, dsi_nlanes * dpi_htotal))
> > + return -EINVAL;
> > +
> > + /* data rate was in bytes/sec, convert to bits/sec. */
> > + dlane_bps *= 8;
> > +
> > + if (dlane_bps > 2500000000UL || dlane_bps < 160000000UL)
> > + return -EINVAL;
> > + else if (dlane_bps >= 1250000000)
> > + cfg->pll_opdiv = 1;
> > + else if (dlane_bps >= 630000000)
> > + cfg->pll_opdiv = 2;
> > + else if (dlane_bps >= 320000000)
> > + cfg->pll_opdiv = 4;
> > + else if (dlane_bps >= 160000000)
> > + cfg->pll_opdiv = 8;
> > +
> > + /*
> > + * Allow a deviation of 0.2% on the per-lane data rate to try to
> > + * recover a potential mismatch between DPI and PPI clks.
> > + */
> > + dlane_bps_max = dlane_bps + (dlane_bps / 500);
>
> kbuild reported an error for 32 bit archs. I'm guessing it's because of
> this divide above?
Yep, DIV_ROUND_UP_ULL() should fix the problem.
>
>
> > +
> > + fbdiv_max = DIV_ROUND_DOWN_ULL((dlane_bps + (dlane_bps / 500)) * 2 *
>
> You could use dlane_bps_max here instead.
Sure.
>
> Otherwise,
>
> Reviewed-by: Archit Taneja <architt@xxxxxxxxxxxxxx>
Thanks for the review.
Does that mean I'm allowed to apply the patch to drm-misc-next myself
after fixing the div64 issue?
Regards,
Boris
_______________________________________________
dri-devel mailing list
dri-devel@xxxxxxxxxxxxxxxxxxxxx
https://lists.freedesktop.org/mailman/listinfo/dri-devel
