Hi Archit & Andrzej, May I ask you please a short review of this documentation update. Many thanks Philippe :-) On 04/09/2018 05:24 PM, Philippe Cornu wrote: > This patch clarifies the adjusted_mode documentation > for bridges. > > Signed-off-by: Philippe Cornu <philippe.cornu@xxxxxx> > Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@xxxxxxxxxxxxxxxx> > --- > This patch follows discussions in: > - "drm: clarify adjusted_mode for a bridge connected to a crtc" > https://patchwork.freedesktop.org/patch/206801/ > - "drm: bridge: Constify mode arguments to bridge .mode_set() operation" > https://patchwork.freedesktop.org/patch/215449/ > > include/drm/drm_bridge.h | 16 ++++++++++++++++ > include/drm/drm_crtc.h | 11 +++++++---- > 2 files changed, 23 insertions(+), 4 deletions(-) > > diff --git a/include/drm/drm_bridge.h b/include/drm/drm_bridge.h > index 3270fec46979..7d632c6a9214 100644 > --- a/include/drm/drm_bridge.h > +++ b/include/drm/drm_bridge.h > @@ -178,6 +178,22 @@ struct drm_bridge_funcs { > * then this would be &drm_encoder_helper_funcs.mode_set. The display > * pipe (i.e. clocks and timing signals) is off when this function is > * called. > + * > + * The adjusted_mode parameter corresponds to the mode output by the CRTC > + * for the first bridge in the chain. It can be different from the mode > + * parameter that contains the desired mode for the connector at the end > + * of the bridges chain, for instance when the first bridge in the chain > + * performs scaling. The adjusted mode is mostly useful for the first > + * bridge in the chain and is likely irrelevant for the other bridges. > + * > + * For atomic drivers the adjusted_mode is the mode stored in > + * &drm_crtc_state.adjusted_mode. > + * > + * NOTE: > + * > + * If a need arises to store and access modes adjusted for other locations > + * than the connection between the CRTC and the first bridge, the DRM > + * framework will have to be extended with DRM bridge states. > */ > void (*mode_set)(struct drm_bridge *bridge, > struct drm_display_mode *mode, > diff --git a/include/drm/drm_crtc.h b/include/drm/drm_crtc.h > index a2d81d2907a9..65f749a9e9d3 100644 > --- a/include/drm/drm_crtc.h > +++ b/include/drm/drm_crtc.h > @@ -134,10 +134,13 @@ struct drm_crtc_state { > * > * Internal display timings which can be used by the driver to handle > * differences between the mode requested by userspace in @mode and what > - * is actually programmed into the hardware. It is purely driver > - * implementation defined what exactly this adjusted mode means. Usually > - * it is used to store the hardware display timings used between the > - * CRTC and encoder blocks. > + * is actually programmed into the hardware. > + * > + * For drivers using drm_bridge, this stores the hardware display timings > + * used between the CRTC and the first bridge. For other drivers, the > + * meaning of the adjusted_mode field is purely driver implementation > + * defined information, and will usually be used to store the hardware > + * display timings used between the CRTC and encoder blocks. > */ > struct drm_display_mode adjusted_mode; > > _______________________________________________ dri-devel mailing list dri-devel@xxxxxxxxxxxxxxxxxxxxx https://lists.freedesktop.org/mailman/listinfo/dri-devel
