On 04/16/2018 08:53 AM, Imre Deak wrote:
LSPCON adapters in low-power state may ignore the first I2C write during
TMDS output buffer enabling, resulting in a blank screen even with an
otherwise enabled pipe. Fix this by reading back and validating the
written value a few times.
The problem was noticed on GLK machines with an onboard LSPCON adapter
after entering/exiting DC5 power state. Doing an I2C read of the adapter
ID as the first transaction - instead of the I2C write to enable the
TMDS buffers - returns the correct value. Based on this we assume that
the transaction itself is sent properly, it's only the adapter that is
not ready for some reason to accept this first write after waking from
low-power state. In my case the second I2C write attempt always
succeeded.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=105854
Cc: Clinton Taylor <clinton.a.taylor@xxxxxxxxx>
Cc: Ville Syrjälä <ville.syrjala@xxxxxxxxxxxxxxx>
Signed-off-by: Imre Deak <imre.deak@xxxxxxxxx>
---
drivers/gpu/drm/drm_dp_dual_mode_helper.c | 39 +++++++++++++++++++++++++------
1 file changed, 32 insertions(+), 7 deletions(-)
diff --git a/drivers/gpu/drm/drm_dp_dual_mode_helper.c b/drivers/gpu/drm/drm_dp_dual_mode_helper.c
index 02a50929af67..e7f4fe2848a5 100644
--- a/drivers/gpu/drm/drm_dp_dual_mode_helper.c
+++ b/drivers/gpu/drm/drm_dp_dual_mode_helper.c
@@ -350,19 +350,44 @@ int drm_dp_dual_mode_set_tmds_output(enum drm_dp_dual_mode_type type,
{
uint8_t tmds_oen = enable ? 0 : DP_DUAL_MODE_TMDS_DISABLE;
ssize_t ret;
+ int retry;
if (type < DRM_DP_DUAL_MODE_TYPE2_DVI)
return 0;
- ret = drm_dp_dual_mode_write(adapter, DP_DUAL_MODE_TMDS_OEN,
- &tmds_oen, sizeof(tmds_oen));
- if (ret) {
- DRM_DEBUG_KMS("Failed to %s TMDS output buffers\n",
- enable ? "enable" : "disable");
- return ret;
+ /*
+ * LSPCON adapters in low-power state may ignore the first write, so
+ * read back and verify the written value a few times.
+ */
+ for (retry = 0; retry < 3; retry++) {
+ uint8_t tmp;
+
+ ret = drm_dp_dual_mode_write(adapter, DP_DUAL_MODE_TMDS_OEN,
+ &tmds_oen, sizeof(tmds_oen));
+ if (ret) {
+ DRM_DEBUG_KMS("Failed to %s TMDS output buffers (%d attempts)\n",
+ enable ? "enable" : "disable",
+ retry + 1);
+ return ret;
+ }
+
+ ret = drm_dp_dual_mode_read(adapter, DP_DUAL_MODE_TMDS_OEN,
+ &tmp, sizeof(tmp));
+ if (ret) {
+ DRM_DEBUG_KMS("I2C read failed during TMDS output buffer %s (%d attempts)\n",
+ enable ? "enabling" : "disabling",
+ retry + 1);
+ return ret;
+ }
+
+ if (tmp == tmds_oen)
+ return 0;
}
- return 0;
+ DRM_DEBUG_KMS("I2C write value mismatch during TMDS output buffer %s\n",
+ enable ? "enabling" : "disabling");
+
+ return -EIO;
}
EXPORT_SYMBOL(drm_dp_dual_mode_set_tmds_output);
Appears to fix the issue seen on GLK with LSPCON and DMC firmware
loaded. Customer was concerned about the fix being in DRM instead of
i915. However, there are no other SOCs that use this DRM function.
Reviewed-by: Clint Taylor <Clinton.A.Taylor@xxxxxxxxx>
Tested-by: Clint Taylor <Clinton.A.Taylor@xxxxxxxxx>
-Clint
_______________________________________________
dri-devel mailing list
dri-devel@xxxxxxxxxxxxxxxxxxxxx
https://lists.freedesktop.org/mailman/listinfo/dri-devel
