On Fri, Apr 13, 2018 at 1:23 AM Sandeep Panda <spanda@xxxxxxxxxxxxxx> wrote:
> Document the bindings used for the sn65dsi86 DSI to eDP bridge.
> Signed-off-by: Sandeep Panda <spanda@xxxxxxxxxxxxxx>
> ---
> .../bindings/display/bridge/ti,sn65dsi86.txt | 75
++++++++++++++++++++++
> 1 file changed, 75 insertions(+)
> create mode 100644
Documentation/devicetree/bindings/display/bridge/ti,sn65dsi86.txt
> diff --git
a/Documentation/devicetree/bindings/display/bridge/ti,sn65dsi86.txt
b/Documentation/devicetree/bindings/display/bridge/ti,sn65dsi86.txt
> new file mode 100644
> index 0000000..cbd2f0e
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/display/bridge/ti,sn65dsi86.txt
> @@ -0,0 +1,75 @@
> +SN65DSI86 DSI to eDP bridge chip
> +--------------------------------
> +
> +This is the binding for Texas Instruments SN65DSI86 bridge.
> +
> +Required properties:
> +- compatible: Must be "ti,sn65dsi86"
> +- reg: i2c address of the chip, 0x2d as per datasheet
> +- enable-gpios: OF device-tree gpio specification for EDP_BRIJ_EN pin
> +- aux-sda-gpios: OF device-tree gpio specification for EDP_BRIJ_I2C_SDA
pin of AUX channel
> +- aux-scl-gpios: OF device-tree gpio specification for EDP_BRIJ_I2C_SCL
pin of AUX channel
> +- bias-en-gpios: OF device-tree gpio specification for EN_PP3300_DX_EDP
pin to
PP3300?
> + enable 3.3V supply to eDP connector
> +- bklt-en-gpios: OF device-tree gpio specification for AP_EDP_BKLTEN pin
I don't see any of these pins listed in the SN65DSI86 datasheet. Can you
please use the actual pin names?
> +
> +- vccio-supply: A 1.8V supply that powers up the PHY.
> +- vcca-supply: A 1.2V supply that powers up the Controller.
> +- vccs-supply: A 3.3V supply that power the eDP connector
> +
> +Optional properties:
> +
> +- irq-gpios: OF device-tree gpio specification for interrupt pin
> +- bklt-ctrl-gpios: OF device-tree gpio specification for EDP_BKLTCTL pin
Same comment here, this isn't listed in the datasheet
> +
> +- sn,is-pluggable: boolean property to specify if HPD supported or not
Could you infer this from whether there's a panel present in the dts?
> +- sn,custom-modes: OF device-tree specifiction to add support for custom
modes
Please drop custom-modes, it doesn't belong on the bridge.
> +
> +Required nodes:
> +
> +This device has two video ports. Their connections are modelled using
the OF
> +graph bindings specified in Documentation/devicetree/bindings/graph.txt.
> +
> +- Video port 0 for DSI input
> +- Video port 1 for eDP output
> +
> +Example
> +-------
> +
> +edp-bridge@2d {
> + compatible = "ti,sn65dsi86";
> + #address-cells = <1>;
> + #size-cells = <0>;
> + reg = <0x2d>;
> +
> + enable-gpios = <&msmgpio 33 GPIO_ACTIVE_HIGH>;
> + aux-sda-gpios = <&msmgpio 34 GPIO_ACTIVE_HIGH>;
> + aux-scl-gpios = <&msmgpio 35 GPIO_ACTIVE_HIGH>;
> + bias-en-gpios = <&msmgpio 36 GPIO_ACTIVE_HIGH>;
> + bklt-en-gpios = <&msmgpio 37 GPIO_ACTIVE_HIGH>;
> +
> + vccio-supply = <&pm8916_l17>;
> + vcca-supply = <&pm8916_l6>;
> + vccs-supply = <&pm8916_l7>;
> +
> + ports {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + port@0 {
> + reg = <0>;
> +
> + edp_bridge_in: endpoint {
> + remote-endpoint = <&dsi_out>;
> + };
> + };
> +
> + port@1 {
> + reg = <1>;
> +
> + edp_bridge_out: endpoint {
> + remote-endpoint = <&edp_panel_in>;
> + };
> + };
> + };
> +}
> --
> The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,
> a Linux Foundation Collaborative Project
_______________________________________________
dri-devel mailing list
dri-devel@xxxxxxxxxxxxxxxxxxxxx
https://lists.freedesktop.org/mailman/listinfo/dri-devel
