From: Boris Brezillon <boris.brezillon@xxxxxxxxxxxxxxxxxx>
Document the bindings used for the Cadence DSI bridge.
Signed-off-by: Boris Brezillon <boris.brezillon@xxxxxxxxxxxxxxxxxx>
---
Hello Rob,
I dropped your Acked-by because this version now documents the DPHY
bindings.
Regards,
Boris
Changes in v6:
- Document the DPHY bindings
- Drop Rob's ack because of the addition DPHY bindings doc
Changes in v5:
- Add optional reset line for the peripheral/APB logic
Changes in v4:
- Rename DSI clks (suggested by Tomi)
- Drop the IP version in the compatible since it can be extracted from
a register (suggested by Andrzej)
Changes in v3:
- Fix clock names in the example
- Document how to represent DSI devices that are controller through
an external bus like I2C or SPI
Changes in v2:
- None
---
.../bindings/display/bridge/cdns,dsi.txt | 133 +++++++++++++++++++++
1 file changed, 133 insertions(+)
create mode 100644 Documentation/devicetree/bindings/display/bridge/cdns,dsi.txt
diff --git a/Documentation/devicetree/bindings/display/bridge/cdns,dsi.txt b/Documentation/devicetree/bindings/display/bridge/cdns,dsi.txt
new file mode 100644
index 000000000000..f5725bb6c61c
--- /dev/null
+++ b/Documentation/devicetree/bindings/display/bridge/cdns,dsi.txt
@@ -0,0 +1,133 @@
+Cadence DSI bridge
+==================
+
+The Cadence DSI bridge is a DPI to DSI bridge supporting up to 4 DSI lanes.
+
+Required properties:
+- compatible: should be set to "cdns,dsi".
+- reg: physical base address and length of the controller's registers.
+- interrupts: interrupt line connected to the DSI bridge.
+- clocks: DSI bridge clocks.
+- clock-names: must contain "dsi_p_clk" and "dsi_sys_clk".
+- phys: phandle link to the MIPI D-PHY controller.
+- phy-names: must contain "dphy".
+- #address-cells: must be set to 1.
+- #size-cells: must be set to 0.
+
+Optional properties:
+- resets: DSI reset lines.
+- reset-names: can contain "dsi_p_rst".
+
+Required subnodes:
+- ports: Ports as described in Documentation/devicetree/bindings/graph.txt.
+ 2 ports are available:
+ * port 0: this port is only needed if some of your DSI devices are
+ controlled through an external bus like I2C or SPI. Can have at
+ most 4 endpoints. The endpoint number is directly encoding the
+ DSI virtual channel used by this device.
+ * port 1: represents the DPI input.
+ Other ports will be added later to support the new kind of inputs.
+
+- one subnode per DSI device connected on the DSI bus. Each DSI device should
+ contain a reg property encoding its virtual channel.
+
+Cadence DPHY
+============
+
+Cadence DPHY block.
+
+Required properties:
+- compatible: should be set to "cdns,dphy".
+- reg: physical base address and length of the DPHY registers.
+- clocks: DPHY reference clocks.
+- clock-names: must contain "psm" and "pll_ref".
+- #phy-cells: must be set to 0.
+
+
+Example:
+ dphy0: dphy@fd0e0000{
+ compatible = "cdns,dphy";
+ reg = <0x0 0xfd0e0000 0x0 0x1000>;
+ clocks = <&psm_clk>, <&pll_ref_clk>;
+ clock-names = "psm", "pll_ref";
+ #phy-cells = <0>;
+ };
+
+ dsi0: dsi@fd0c0000 {
+ compatible = "cdns,dsi";
+ reg = <0x0 0xfd0c0000 0x0 0x1000>;
+ clocks = <&pclk>, <&sysclk>;
+ clock-names = "dsi_p_clk", "dsi_sys_clk";
+ interrupts = <1>;
+ phys = <&dphy0>;
+ phy-names = "dphy";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@1 {
+ reg = <1>;
+ dsi0_dpi_input: endpoint {
+ remote-endpoint = <&xxx_dpi_output>;
+ };
+ };
+ };
+
+ panel: dsi-dev@0 {
+ compatible = "<vendor,panel>";
+ reg = <0>;
+ };
+ };
+
+or
+
+ dsi0: dsi@fd0c0000 {
+ compatible = "cdns,dsi";
+ reg = <0x0 0xfd0c0000 0x0 0x1000>;
+ clocks = <&pclk>, <&sysclk>;
+ clock-names = "dsi_p_clk", "dsi_sys_clk";
+ interrupts = <1>;
+ phys = <&dphy1>;
+ phy-names = "dphy";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ dsi0_output: endpoint@0 {
+ reg = <0>;
+ remote-endpoint = <&dsi_panel_input>;
+ };
+ };
+
+ port@1 {
+ reg = <1>;
+ dsi0_dpi_input: endpoint {
+ remote-endpoint = <&xxx_dpi_output>;
+ };
+ };
+ };
+ };
+
+ i2c@xxx {
+ panel: panel@59 {
+ compatible = "<vendor,panel>";
+ reg = <0x59>;
+
+ port {
+ dsi_panel_input: endpoint {
+ remote-endpoint = <&dsi0_output>;
+ };
+ };
+ };
+ };
--
2.14.1
_______________________________________________
dri-devel mailing list
dri-devel@xxxxxxxxxxxxxxxxxxxxx
https://lists.freedesktop.org/mailman/listinfo/dri-devel
