On Wed, 2018-04-04 at 21:53 +0300, Ville Syrjälä wrote:
> On Wed, Apr 04, 2018 at 02:37:41PM -0400, Lyude Paul wrote:
> > On Wed, 2018-04-04 at 18:34 +0300, Ville Syrjälä wrote:
> > > On Mon, Apr 02, 2018 at 05:26:16PM -0400, Lyude Paul wrote:
> > > > While enabling/disabling DPMS before link training with MST hubs is
> > > > perfectly valid; unfortunately disabling DPMS results in some devices
> > > > disabling their AUX CH block as well. For SST this isn't as much of a
> > > > problem, but for MST we need to be able to continue handling aux
> > > > transactions even when none of the sinks are turned on since it's
> > > > possible for us to have a single atomic commit which results in
> > > > disabling each downstream sink, followed by subsequently re-enabling
> > > > each sink.
> > > >
> > > > If we don't do this, we'll end up stalling any pending ESI interrupts
> > > > from the sink for up to 1ms. Unfortunately, dropping ESIs during this
> > > > timespan makes it so that link fallback retraining for MST (which I
> > > > will
> > > > be submitting to the ML shortly) fails due to the channel EQ failure
> > > > interrupts potentially getting dropped. Additionally, when performing
> > > > a
> > > > modeset that brings the hub status's link status from bad -> good
> > > > having
> > > > ESIs disabled for that long causes us to miss the hub's response to us
> > > > trying to start link training as well.
> > > >
> > > > Since any sink with MST is going to support DisplayPort 1.2 anyway,
> > > > save
> > > > us the hassle of trying to wait until the sink comes back up and just
> > > > never shut the aux block down.
> > > >
> > > > Changes since v2:
> > > > - Fix patch name, no functional changes
> > > >
> > > > Signed-off-by: Lyude Paul <lyude@xxxxxxxxxx>
> > > > Cc: Laura Abbott <labbott@xxxxxxxxxx>
> > > > Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@xxxxxxxxx>
> > > > Cc: Ville Syrjälä <ville.syrjala@xxxxxxxxxxxxxxx>
> > > > Cc: stable@xxxxxxxxxxxxxxx
> > > > Fixes: ad260ab32a4d9 ("drm/i915/dp: Write to SET_POWER dpcd to enable
> > > > MST
> > > > hub.")
> > > > ---
> > > > drivers/gpu/drm/i915/intel_dp.c | 6 ++++--
> > > > 1 file changed, 4 insertions(+), 2 deletions(-)
> > > >
> > > > diff --git a/drivers/gpu/drm/i915/intel_dp.c
> > > > b/drivers/gpu/drm/i915/intel_dp.c
> > > > index 62f82c4298ac..0479c377981b 100644
> > > > --- a/drivers/gpu/drm/i915/intel_dp.c
> > > > +++ b/drivers/gpu/drm/i915/intel_dp.c
> > > > @@ -2589,11 +2589,13 @@ void intel_dp_sink_dpms(struct intel_dp
> > > > *intel_dp,
> > > > int mode)
> > > > return;
> > > >
> > > > if (mode != DRM_MODE_DPMS_ON) {
> > > > + unsigned char data = intel_dp->is_mst ?
> > > > + DP_SET_POWER_D3_AUX_ON : DP_SET_POWER_D3;
> > >
> > > This smells like a workaround for an actual bug somewhere. Why exactly
> > > is the slower wakeup or the AUX block a problem for MST but not for SST
> > > when the link training is exactly the same for SST and MST?
> >
> > I actually thought about this but I still think this is the appropriate
> > fix.
> > So; the real reason for the wakeup not being a problem with SST is that
> > for
> > DPMS on with SST, we actually do a wait to make sure that the hub is ready
> > before continuing. And yes: I'm fairly sure SST does actually have around
> > the
> > same wakeup time that MST does, but with the wait we do it doesn't reallhy
> > make a difference. With MST, we could do this but there's a few reasons I
> > don't think we should:
> > * We don't need to. D3_AUX_ON is a part of the 1.2 spec, so any hub that
> > has
> > MST is going to be guaranteed to have this.
> > * Turning off the aux block means that there's a high chance we're going
> > to
> > miss ESIs from sinks
>
> And how exactly do we lose irqs? The hub/whatever throws the up req msgs
> away if we don't read them within some really short time?
Oh-additionally I did forget to mention that i have actually witnessed the
channel eq failures in the ESI getting dropped without this patch. Meaning if
we miss them, there's a chance the hub may just not choose to send them again
for whatever reason.
>
> > * It's faster to keep the aux block on anyway
> >
> >
> > >
> > > > +
> > > > if (downstream_hpd_needs_d0(intel_dp))
> > > > return;
> > > >
> > > > - ret = drm_dp_dpcd_writeb(&intel_dp->aux,
> > > > DP_SET_POWER,
> > > > - DP_SET_POWER_D3);
> > > > + ret = drm_dp_dpcd_writeb(&intel_dp->aux,
> > > > DP_SET_POWER,
> > > > data);
> > > > } else {
> > > > struct intel_lspcon *lspcon = dp_to_lspcon(intel_dp);
> > > >
> > > > --
> > > > 2.14.3
> > >
> > >
> >
> > --
> > Cheers,
> > Lyude Paul
>
>
--
Cheers,
Lyude Paul
_______________________________________________
dri-devel mailing list
dri-devel@xxxxxxxxxxxxxxxxxxxxx
https://lists.freedesktop.org/mailman/listinfo/dri-devel
