Hi Peter,
(CC'ing Jacopo Mondi who might be working on something similar)
On Sunday, 18 March 2018 00:15:22 EET Peter Rosin wrote:
> I'm trying to get something to work that I assumed would not
> need patches, so I think I might be missing something completely
> obvious...
>
> I have an Atmel sama5d31 hooked up to an lvds encoder and then
> on to an lvds panel. Which seems like something that has been
> done one or two times before...
>
> The problem (I think) is that the bus_format of the SoC and the
> panel do not agree. The SoC driver (atmel-hlcdc) can handle the
> rgb444, rgb565, rgb666 and rgb888 bus formats. The hardware is
> wired for the rgb565 case. The lvds encoder supports rgb888 on
> its input side with the LSB wires simply pulled down internally
> in the encoder in my case. And the panel is expecting lvds
> (vesa-24), which is what the encoder outputs.
>
> The reason I "blame" the bus_format of the drm_connector is that
> with the below DT snippet, things do not work *exactly* due to
> that. At least, it starts to work if I hack the panel-lvds driver
> to report the rgb565 bus_format instead of vesa-24.
>
> panel: panel {
> compatible = "panel-lvds";
>
> width-mm = <476>;
> height-mm = <268>;
>
> data-mapping = "vesa-24";
>
> panel-timing {
> // 1024x768 @ 60Hz (typical)
> clock-frequency = <52140000 65000000 71100000>;
> hactive = <1024>;
> vactive = <768>;
> hfront-porch = <59 107 107>;
> hback-porch = <59 107 107>;
> hsync-len = <59 106 106>;
> vfront-porch = <8 13 14>;
> vback-porch = <8 13 14>;
> vsync-len = <8 12 14>;
> };
>
> port {
> panel_input: endpoint {
> remote-endpoint = <&lvds_encoder_output>;
> };
> };
> };
>
> lvds-encoder {
> compatible = "ti,ds90c187", "lvds-encoder";
>
> ports {
> #address-cells = <1>;
> #size-cells = <0>;
>
> port@0 {
> reg = <0>;
>
> lvds_encoder_input: endpoint {
> remote-endpoint = <&hlcdc_output>;
> };
> };
>
> port@1 {
> reg = <1>;
>
> lvds_encoder_output: endpoint {
> remote-endpoint = <&panel_input>;
> };
> };
> };
> };
I agree with your analysis, it's wrong for a display controller to use the
formats reported by the panel (through the connector) without taking into
account intermediate bridges.
> But, instead of perverting the panel-lvds driver with support
> for a totally fake non-lvds bus_format, I came up with an optional
> bus_format override in the lvds-encoder driver, which I trigger with
> this addition to the lvds-encoder DT node:
>
> interface-pix-fmt = "rgb565";
>
> There are some issues with the interface-pix-fmt name. I copied it
> from the freescale fsl-imx-drm binding, but a) I personally don't
> like how that binding uses rgb24 instead of rgb888 and b) I don't
> like how the implementation of that binding selects rgb666 when you
> say bgr666 in the DT, but for parallel hardware interface the bit
> order is not really relevant so I swallowed that. Anyway, it might
> be better to use something else than interface-pix-fmt? Perhaps
> reuse the "data-mapping" name from the panel-lvds binding? But that
> seems somewhat lvds specific? Then there a couple of instances of
> "bus-format-override" in some dtsi files, but that name is not
> mentioned in any binding, nor in (upstream) code...
The data-mappings property describe the mapping of the bits over the LVDS time
slots, so I wouldn't reuse that name, especially given that the property you
need isn't specific to LVDS. "bus-format" sounds better to me, or maybe
"video-format" (coming from a similar property in a Xilinx-specific V4L2
binding).
> And maybe it should be fourcc codes or something instead of these
> "rgb565" names?
We'd end up introducing the format fourcc values, which are to some extent
Linux-specific (with identical formats that have different fourccs in V4L2 and
DRM), in the DT bindings, so I'm tempted to stick to strings, but I could be
convinced otherwise.
Another option would be to use device-specific compatible strings, in which
case the format could be stored in the driver instead of in a DT property. I'm
not sure that's a good idea, I haven't really thought about it much :-)
> I threw in the first patch, since that is the actual lvds encoder
> I have in this case.
>
> Suggestions welcome.
I'll comment on the API in replies to the patches.
> Peter Rosin (3):
> dt-bindings: display: bridge: lvds-transmitter: add ti,ds90c185
> drm: bridge: panel: allow override of the bus format
> drm: bridge: lvds-encoder: on request, override the bus format
>
> .../bindings/display/bridge/lvds-transmitter.txt | 13 +++++++++++++
> drivers/gpu/drm/bridge/lvds-encoder.c | 18 ++++++++++++++++++
> drivers/gpu/drm/bridge/panel.c | 22 ++++++++++++++++++-
> include/drm/drm_bridge.h | 1 +
> 4 files changed, 53 insertions(+), 1 deletion(-)
--
Regards,
Laurent Pinchart
_______________________________________________
dri-devel mailing list
dri-devel@xxxxxxxxxxxxxxxxxxxxx
https://lists.freedesktop.org/mailman/listinfo/dri-devel
