From: Hans Verkuil <hans.verkuil@xxxxxxxxx>
The CEC Pin framework adds support for Error Injection.
Document all the error injections commands and how to use it.
Signed-off-by: Hans Verkuil <hans.verkuil@xxxxxxxxx>
---
.../media/cec-drivers/cec-pin-error-inj.rst | 322 +++++++++++++++++++++
Documentation/media/cec-drivers/index.rst | 1 +
MAINTAINERS | 1 +
3 files changed, 324 insertions(+)
create mode 100644 Documentation/media/cec-drivers/cec-pin-error-inj.rst
diff --git a/Documentation/media/cec-drivers/cec-pin-error-inj.rst b/Documentation/media/cec-drivers/cec-pin-error-inj.rst
new file mode 100644
index 000000000000..21bda831d3fb
--- /dev/null
+++ b/Documentation/media/cec-drivers/cec-pin-error-inj.rst
@@ -0,0 +1,322 @@
+CEC Pin Framework Error Injection
+=================================
+
+The CEC Pin Framework is a core CEC framework for CEC hardware that only
+has low-level support for the CEC bus. Most hardware today will have
+high-level CEC support where the hardware deals with driving the CEC bus,
+but some older devices aren't that fancy. However, this framework also
+allows you to connect the CEC pin to a GPIO on e.g. a Raspberry Pi and
+you can become an instant CEC adapter.
+
+What makes doing this so interesting is that since we have full control
+over the bus it is easy to support error injection. This is ideal to
+test how well CEC adapters can handle error conditions.
+
+Currently only the cec-gpio driver (when the CEC line is directly
+connected to a pull-up GPIO line) and the AllWinner A10/A20 drm driver
+support this framework.
+
+If ``CONFIG_CEC_PIN_ERROR_INJ`` is enabled, then error injection is available
+through debugfs. Specifically, in ``/sys/kernel/debug/cec/cecX/`` there is
+now an ``error-inj`` file.
+
+With ``cat error-inj`` you can see both the possible commands and the current
+error injection status:
+
+.. code-block:: none
+
+ $ cat /sys/kernel/debug/cec/cec0/error-inj
+ # Clear error injections:
+ # clear clear all rx and tx error injections
+ # rx-clear clear all rx error injections
+ # tx-clear clear all tx error injections
+ # <op> clear clear all rx and tx error injections for <op>
+ # <op> rx-clear clear all rx error injections for <op>
+ # <op> tx-clear clear all tx error injections for <op>
+ #
+ # RX error injection:
+ # <op>[,<mode>] rx-nack NACK the message instead of sending an ACK
+ # <op>[,<mode>] rx-low-drive <bit> force a low-drive condition at this bit position
+ # <op>[,<mode>] rx-add-byte add a spurious byte to the received CEC message
+ # <op>[,<mode>] rx-remove-byte remove the last byte from the received CEC message
+ # <op>[,<mode>] rx-arb-lost <poll> generate a POLL message to trigger an arbitration lost
+ #
+ # TX error injection settings:
+ # tx-ignore-nack-until-eom ignore early NACKs until EOM
+ # tx-custom-low-usecs <usecs> define the 'low' time for the custom pulse
+ # tx-custom-high-usecs <usecs> define the 'high' time for the custom pulse
+ # tx-custom-pulse transmit the custom pulse once the bus is idle
+ #
+ # TX error injection:
+ # <op>[,<mode>] tx-no-eom don't set the EOM bit
+ # <op>[,<mode>] tx-early-eom set the EOM bit one byte too soon
+ # <op>[,<mode>] tx-add-bytes <num> append <num> (1-255) spurious bytes to the message
+ # <op>[,<mode>] tx-remove-byte drop the last byte from the message
+ # <op>[,<mode>] tx-short-bit <bit> make this bit shorter than allowed
+ # <op>[,<mode>] tx-long-bit <bit> make this bit longer than allowed
+ # <op>[,<mode>] tx-custom-bit <bit> send the custom pulse instead of this bit
+ # <op>[,<mode>] tx-short-start send a start pulse that's too short
+ # <op>[,<mode>] tx-long-start send a start pulse that's too long
+ # <op>[,<mode>] tx-custom-start send the custom pulse instead of the start pulse
+ # <op>[,<mode>] tx-last-bit <bit> stop sending after this bit
+ # <op>[,<mode>] tx-low-drive <bit> force a low-drive condition at this bit position
+ #
+ # <op> CEC message opcode (0-255) or 'any'
+ # <mode> 'once' (default), 'always', 'toggle' or 'off'
+ # <bit> CEC message bit (0-159)
+ # 10 bits per 'byte': bits 0-7: data, bit 8: EOM, bit 9: ACK
+ # <poll> CEC poll message used to test arbitration lost (0x00-0xff, default 0x0f)
+ # <usecs> microseconds (0-10000000, default 1000)
+
+ clear
+
+You can write error injection commands to ``error-inj`` using ``echo 'cmd' >error-inj``
+or ``cat cmd.txt >error-inj``. The ``cat error-inj`` output contains the current
+error commands. You can save the output to a file and use it as an input to
+``error-inj`` later.
+
+Basic Syntax
+------------
+
+Leading spaces/tabs are ignored. If the next character is a ``#`` or the end of the
+line was reached, then the whole line is ignored. Otherwise a command is expected.
+
+The error injection commands fall in two main groups: those relating to receiving
+CEC messages and those relating to transmitting CEC messages. In addition, there
+are commands to clear existing error injection commands and to create custom
+pulses on the CEC bus.
+
+Most error injection commands can be executed for specific CEC opcodes or for all
+opcodes (``any``). Each command also has a 'mode' which can be ``off`` (can be used
+to turn off an existing error injection command), ``once`` (the default) which will
+trigger the error injection only once for the next received or transmitted message,
+``always`` to always trigger the error injection and ``toggle`` to toggle the error
+injection on or off for every transmit or receive.
+
+So '``any rx-nack``' will NACK the next received CEC message, '``any,always rx-nack``' will
+NACK all received CEC messages and '``0x82,toggle rx-nack``' will only NACK if an Active
+Source message was received and do that only for every other received message.
+
+After an error was injected with mode ``once`` the error injection command is cleared
+automatically, so ``once`` is a one-time deal.
+
+All combinations of ``<op>`` and error injection commands can co-exist. So
+this is fine:
+
+.. code-block:: none
+
+ 0x9e tx-add-bytes 1
+ 0x9e tx-early-eom
+ 0x9f tx-add-bytes 2
+ any rx-nack
+
+All four error injection commands will be active simultaneously.
+
+However, if the same ``<op>`` and command combination is specified,
+but with different arguments:
+
+.. code-block:: none
+
+ 0x9e tx-add-bytes 1
+ 0x9e tx-add-bytes 2
+
+Then the second will overwrite the first.
+
+Clear Error Injections
+----------------------
+
+``clear``
+ Clear all error injections.
+
+``rx-clear``
+ Clear all receive error injections
+
+``tx-clear``
+ Clear all transmit error injections
+
+``<op> clear``
+ Clear all error injections for the given opcode.
+
+``<op> rx-clear``
+ Clear all receive error injections for the given opcode.
+
+``<op> tx-clear``
+ Clear all transmit error injections for the given opcode.
+
+Receive Messages
+----------------
+
+``<op>[,<mode>] rx-nack``
+ NACK broadcast messages and messages directed to this CEC adapter.
+ Every byte of the message will be NACKed in case the transmitter
+ keeps transmitting after the first byte was NACKed.
+
+``<op>[,<mode>] rx-low-drive <bit>``
+ Force a Low Drive condition at this bit position. If <op> specifies
+ a specific CEC opcode then the bit position must be at least 18,
+ otherwise the opcode hasn't been received yet. This tests if the transmitter
+ can handle the Low Drive condition correctly and reports the error
+ correctly. Note that a Low Drive in the first 4 bits can also be
+ interpreted as an Arbitration Lost condition by the transmitter.
+ This is implementation dependent.
+
+``<op>[,<mode>] rx-add-byte``
+ Add a spurious 0x55 byte to the received CEC message, provided
+ the message was 15 bytes long or less. This is useful to test
+ the high-level protocol since spurious bytes should be ignored.
+
+``<op>[,<mode>] rx-remove-byte``
+ Remove the last byte from the received CEC message, provided it
+ was at least 2 bytes long. This is useful to test the high-level
+ protocol since messages that are too short should be ignored.
+
+``<op>[,<mode>] rx-arb-lost <poll>``
+ Generate a POLL message to trigger an Arbitration Lost condition.
+ This command is only allowed for ``<op>`` values of ``next`` or ``all``.
+ As soon as a start bit has been received the CEC adapter will switch
+ to transmit mode and it will transmit a POLL message. By default this is
+ 0x0f, but it can also be specified explicitly via the ``<poll>`` argument.
+
+ This command can be used to test the Arbitration Lost condition in
+ the remote CEC transmitter. Arbitration happens when two CEC adapters
+ start sending a message at the same time. In that case the initiator
+ with the most leading zeroes wins and the other transmitter has to
+ stop transmitting ('Arbitration Lost'). This is very hard to test,
+ except by using this error injection command.
+
+ This does not work if the remote CEC transmitter has logical address
+ 0 ('TV') since that will always win.
+
+Transmit Messages
+-----------------
+
+``tx-ignore-nack-until-eom``
+ This setting changes the behavior of transmitting CEC messages. Normally
+ as soon as the receiver NACKs a byte the transmit will stop, but the
+ specification also allows that the full message is transmitted and only
+ at the end will the transmitter look at the ACK bit. This is not recommended
+ behavior since there is no point in keeping the CEC bus busy for longer than
+ is strictly needed. Especially given how slow the bus is.
+
+ This setting can be used to test how well a receiver deals with transmitters
+ that ignore NACKs until the very end of the message.
+
+``<op>[,<mode>] tx-no-eom``
+ Don't set the EOM bit. Normally the last byte of the message has the EOM
+ (End-Of-Message) bit set. With this command the transmit will just stop
+ without ever sending an EOM. This can be used to test how a receiver
+ handles this case. Normally receivers have a time-out after which
+ they will go back to the Idle state.
+
+``<op>[,<mode>] tx-early-eom``
+ Set the EOM bit one byte too soon. This obviously only works for messages
+ of two bytes or more. The EOM bit will be set for the second-to-last byte
+ and not for the final byte. The receiver should ignore the last byte in this
+ case. Since the resulting message is likely to be too short for this same
+ reason the whole message is typically ignored. The receiver should be in
+ Idle state after the last byte was transmitted.
+
+``<op>[,<mode>] tx-add-bytes <num>``
+ Append ``<num>`` (1-255) spurious bytes to the message. The extra bytes
+ have the value of the byte position in the message. So if you transmit a
+ two byte message (e.g. a Get CEC Version message) and add 2 bytes, then
+ the full message received by the remote CEC adapter is ``0x40 0x9f 0x02 0x03``.
+
+ This command can be used to test buffer overflows in the receiver. E.g.
+ what does it do when it receives more than the maximum message size of 16
+ bytes.
+
+``<op>[,<mode>] tx-remove-byte``
+ Drop the last byte from the message, provided the message is at least
+ two bytes long. The receiver should ignore messages that are too short.
+
+``<op>[,<mode>] tx-short-bit <bit>``
+ Make this bit period shorter than allowed. The bit position cannot be
+ an Ack bit. If <op> specifies a specific CEC opcode then the bit position
+ must be at least 18, otherwise the opcode hasn't been received yet. Normally the
+ period of a data bit is between 2.05 and 2.75 milliseconds. With this
+ command the period of this bit is 1.8 milliseconds, this is done by
+ reducing the time the CEC bus is high. This bit period is less than
+ is allowed and the receiver should respond with a Low Drive
+ condition.
+
+ This command is ignored for 0 bits in bit positions 0 to 3. This is
+ because the receiver also looks for an Arbitration Lost condition in
+ those first four bits and it is undefined what will happen if it
+ sees a too-short 0 bit.
+
+``<op>[,<mode>] tx-long-bit <bit>``
+ Make this bit period longer than is valid. The bit position cannot be
+ an Ack bit. If <op> specifies a specific CEC opcode then the bit position
+ must be at least 18, otherwise the opcode hasn't been received yet. Normally the
+ period of a data bit is between 2.05 and 2.75 milliseconds. With this
+ command the period of this bit is 2.9 milliseconds, this is done by
+ increasing the time the CEC bus is high.
+
+ Even though this bit period is longer than is valid it is undefined what
+ a receiver will do. It might just accept it, or it might time out and
+ return to Idle state. Unfortunately the CEC specification is silent about
+ this.
+
+ This command is ignored for 0 bits in bit positions 0 to 3. This is
+ because the receiver also looks for an Arbitration Lost condition in
+ those first four bits and it is undefined what will happen if it
+ sees a too-long 0 bit.
+
+``<op>[,<mode>] tx-short-start``
+ Make this start bit period shorter than allowed. Normally the period of a start bit is
+ between 4.3 and 4.7 milliseconds. With this command the period of the
+ start bit is 4.1 milliseconds, this is done by reducing the time the
+ CEC bus is high. This start bit period is less than is allowed
+ and the receiver should return to Idle state when this is detected.
+
+``<op>[,<mode>] tx-long-start``
+ Make this start bit period longer than is valid. Normally the period of a start bit is
+ between 4.3 and 4.7 milliseconds. With this command the period of the
+ start bit is 5 milliseconds, this is done by increasing the time the
+ CEC bus is high. This start bit period is more than is valid
+ and the receiver should return to Idle state when this is detected.
+
+ Even though this start bit period is longer than is valid it is undefined what
+ a receiver will do. It might just accept it, or it might time out and
+ return to Idle state. Unfortunately the CEC specification is silent about
+ this.
+
+``<op>[,<mode>] tx-last-bit <bit>``
+ Just stop transmitting after this bit. If <op> specifies a specific CEC
+ opcode then the bit position must be at least 18, otherwise the opcode
+ hasn't been received yet. This command can be used to test how the receiver reacts
+ when a message just suddenly stops. It should time out and go back to Idle
+ state.
+
+``<op>[,<mode>] tx-low-drive <bit>``
+ Force a Low Drive condition at this bit position. If <op> specifies a specific
+ CEC opcode then the bit position must be at least 18, otherwise the opcode
+ hasn't been received yet. This can be used to test how the receiver handles Low Drive
+ conditions. Note that if this happens at bit positions 0-3 the receiver
+ can interpret this as an Arbitration Lost condition. This is implementation
+ dependent.
+
+Custom Pulses
+-------------
+
+``tx-custom-low-usecs <usecs>``
+ This defines the duration in microseconds that the custom pulse pulls the CEC line low.
+ The default is 1000 microseconds.
+
+``tx-custom-high-usecs <usecs>``
+ This defines the duration in microseconds that the custom pulse keeps the
+ CEC line high (unless another CEC adapter pulls it low in that time).
+ The default is 1000 microseconds. The total period of the custom pulse is
+ ``tx-custom-low-usecs + tx-custom-high-usecs``.
+
+``<op>[,<mode>] tx-custom-bit <bit>``
+ Send the custom bit instead of a regular data bit. The bit position cannot be
+ an Ack bit. If <op> specifies a specific CEC opcode then the bit position
+ must be at least 18, otherwise the opcode hasn't been received yet.
+
+``<op>[,<mode>] tx-custom-start``
+ Send the custom bit instead of a regular start bit.
+
+``tx-custom-pulse``
+ Transmit a single custom pulse as soon as the CEC bus is idle.
diff --git a/Documentation/media/cec-drivers/index.rst b/Documentation/media/cec-drivers/index.rst
index 7ef204823422..3580bdb790bc 100644
--- a/Documentation/media/cec-drivers/index.rst
+++ b/Documentation/media/cec-drivers/index.rst
@@ -31,4 +31,5 @@ For more details see the file COPYING in the source distribution of Linux.
:maxdepth: 5
:numbered:
+ cec-pin-error-inj
pulse8-cec
diff --git a/MAINTAINERS b/MAINTAINERS
index 91ed6adfa4a6..085b40adbe4d 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -3305,6 +3305,7 @@ F: include/media/cec-notifier.h
F: include/uapi/linux/cec.h
F: include/uapi/linux/cec-funcs.h
F: Documentation/devicetree/bindings/media/cec.txt
+F: Documentation/media/cec-drivers/cec-pin-error-inj.rst
CEC GPIO DRIVER
M: Hans Verkuil <hans.verkuil@xxxxxxxxx>
--
2.16.1
_______________________________________________
dri-devel mailing list
dri-devel@xxxxxxxxxxxxxxxxxxxxx
https://lists.freedesktop.org/mailman/listinfo/dri-devel
