Hi Kieran, Thank you for the patch. On Tuesday, 13 February 2018 00:07:49 EET Kieran Bingham wrote: > From: Jean-Michel Hautbois <jean-michel.hautbois@xxxxxxxxxxx> > > The ADV7604 has thirteen 256-byte maps that can be accessed via the main > I²C ports. Each map has it own I²C address and acts as a standard slave > device on the I²C bus. > > Extend the device tree node bindings to be able to override the default > addresses so that address conflicts with other devices on the same bus > may be resolved at the board description level. > > Signed-off-by: Jean-Michel Hautbois <jean-michel.hautbois@xxxxxxxxxxx> > [Kieran: Re-adapted for mainline] > Signed-off-by: Kieran Bingham <kieran.bingham+renesas@xxxxxxxxxxxxxxxx> > Reviewed-by: Rob Herring <robh@xxxxxxxxxx> Nitpicking, I might not mention i2c_new_secondary_device in the subject, as this is a DT bindings change. I don't mind too much though, as long as the bindings themselves don't contain Linux-specific information, and they don't, so Reviewed-by: Laurent Pinchart <laurent.pinchart@xxxxxxxxxxxxxxxx> > --- > Based upon the original posting : > https://lkml.org/lkml/2014/10/22/469 > > v2: > - DT Binding update separated from code change > - Minor reword to commit message to account for DT only change. > - Collected Rob's RB tag. > > v3: > - Split map register addresses into individual declarations. > > .../devicetree/bindings/media/i2c/adv7604.txt | 18 > ++++++++++++++++-- 1 file changed, 16 insertions(+), 2 deletions(-) > > diff --git a/Documentation/devicetree/bindings/media/i2c/adv7604.txt > b/Documentation/devicetree/bindings/media/i2c/adv7604.txt index > 9cbd92eb5d05..ebb5f070c05b 100644 > --- a/Documentation/devicetree/bindings/media/i2c/adv7604.txt > +++ b/Documentation/devicetree/bindings/media/i2c/adv7604.txt > @@ -13,7 +13,11 @@ Required Properties: > - "adi,adv7611" for the ADV7611 > - "adi,adv7612" for the ADV7612 > > - - reg: I2C slave address > + - reg: I2C slave addresses > + The ADV76xx has up to thirteen 256-byte maps that can be accessed via > the + main I²C ports. Each map has it own I²C address and acts as a > standard + slave device on the I²C bus. The main address is mandatory, > others are + optional and revert to defaults if not specified. > > - hpd-gpios: References to the GPIOs that control the HDMI hot-plug > detection pins, one per HDMI input. The active flag indicates the GPIO > @@ -35,6 +39,11 @@ Optional Properties: > > - reset-gpios: Reference to the GPIO connected to the device's reset pin. > - default-input: Select which input is selected after reset. > + - reg-names : Names of maps with programmable addresses. > + It can contain any map needing a non-default address. > + Possible maps names are : > + "main", "avlink", "cec", "infoframe", "esdp", "dpp", "afe", > + "rep", "edid", "hdmi", "test", "cp", "vdp" > > Optional Endpoint Properties: > > @@ -52,7 +61,12 @@ Example: > > hdmi_receiver@4c { > compatible = "adi,adv7611"; > - reg = <0x4c>; > + /* > + * The edid page will be accessible @ 0x66 on the i2c bus. All > + * other maps will retain their default addresses. > + */ > + reg = <0x4c>, <0x66>; > + reg-names "main", "edid"; > > reset-gpios = <&ioexp 0 GPIO_ACTIVE_LOW>; > hpd-gpios = <&ioexp 2 GPIO_ACTIVE_HIGH>; -- Regards, Laurent Pinchart _______________________________________________ dri-devel mailing list dri-devel@xxxxxxxxxxxxxxxxxxxxx https://lists.freedesktop.org/mailman/listinfo/dri-devel
