On Wed, Feb 07, 2018 at 11:41:49AM -0600, Rob Herring wrote: > On Tue, Feb 6, 2018 at 3:48 PM, Sean Paul <seanpaul@xxxxxxxxxxxx> wrote: > > On Tue, Feb 06, 2018 at 02:19:34PM -0600, Rob Herring wrote: > >> On Tue, Feb 6, 2018 at 10:56 AM, Sean Paul <seanpaul@xxxxxxxxxxxx> wrote: > >> > This patch adds the ability to override the typical display timing for a > >> > given panel. This is useful for devices which have timing constraints > >> > that do not apply across the entire display driver (eg: to avoid > >> > crosstalk between panel and digitizer on certain laptops). The rules are > >> > as follows: > >> > > >> > - panel must not specify fixed mode (since the override mode will > >> > either be the same as the fixed mode, or we'll be unable to > >> > check the bounds of the overried) > >> > - panel must specify at least one display_timing range which will be > >> > used to ensure the override mode fits within its bounds > >> > > >> > Cc: Doug Anderson <dianders@xxxxxxxxxxxx> > >> > Cc: Heiko Stuebner <heiko@xxxxxxxxx> > >> > Cc: Jeffy Chen <jeffy.chen@xxxxxxxxxxxxxx> > >> > Cc: Rob Herring <robh+dt@xxxxxxxxxx> > >> > Cc: Stéphane Marchesin <marcheu@xxxxxxxxxxxx> > >> > Cc: Thierry Reding <thierry.reding@xxxxxxxxx> > >> > Cc: devicetree@xxxxxxxxxxxxxxx > >> > Cc: dri-devel@xxxxxxxxxxxxxxxxxxxxx > >> > Cc: linux-rockchip@xxxxxxxxxxxxxxxxxxx > >> > Signed-off-by: Sean Paul <seanpaul@xxxxxxxxxxxx> > >> > --- > >> > .../bindings/display/panel/simple-panel.txt | 20 +++++++ > >> > >> The binding should be a separate patch. > >> > > > > Ack, will split. > > > > > >> > drivers/gpu/drm/panel/panel-simple.c | 69 +++++++++++++++++++++- > >> > 2 files changed, 88 insertions(+), 1 deletion(-) > >> > > >> > diff --git a/Documentation/devicetree/bindings/display/panel/simple-panel.txt b/Documentation/devicetree/bindings/display/panel/simple-panel.txt > >> > index 16d8ff088b7d..590bbff6fc90 100644 > >> > --- a/Documentation/devicetree/bindings/display/panel/simple-panel.txt > >> > +++ b/Documentation/devicetree/bindings/display/panel/simple-panel.txt > >> > @@ -7,6 +7,14 @@ Optional properties: > >> > - ddc-i2c-bus: phandle of an I2C controller used for DDC EDID probing > >> > - enable-gpios: GPIO pin to enable or disable the panel > >> > - backlight: phandle of the backlight device attached to the panel > >> > +- override-mode: For devices which require a mode which differs from the > >> > >> This is not a property, but a node so it needs its own section. > >> > >> Also, it's not real clear from display-timing.txt, but the modes > >> should be grouped under a display-timings node. Looks like we haven't > >> been good at enforcing that as "panel-timing" is also common when > >> there's a single mode. I'd rather not have another way. With a > >> standard node name, we can validate the node more easily. > >> > >> We'd lose the fact that this is explicitly an override, but I'd doubt > >> Thierry is going to start letting in panels with no timings. > >> > > > > Yeah, I noticed that the timing subnode was specified as nestled in > > display-timings. I figured since there can only be one override mode, and the > > of_get_display_timing function was exported, it would be Ok to just reuse the > > format of the subnode. I'll respin with the full thing. > > TBC, I'm fine if you use panel-timing as that's already established > for cases were only 1 mode exists. Ah! So the dt change you were asking for was just s/override-mode/panel-timing/. I'll respin a v3 with the improved documentation and reinstate the "panel-timing" subnode. Sean > > Rob -- Sean Paul, Software Engineer, Google / Chromium OS _______________________________________________ dri-devel mailing list dri-devel@xxxxxxxxxxxxxxxxxxxxx https://lists.freedesktop.org/mailman/listinfo/dri-devel
