On Wed, Jan 17, 2018 at 09:14:15PM +0100, Jernej Skrabec wrote:
> This commit adds all necessary compatibles and descriptions needed to
> implement A83T HDMI pipeline.
>
> Mixer is already properly described, so only compatible is added.
>
> However, A83T TV TCON, which is connected to HDMI, doesn't have channel 0,
> contrary to all TCONs currently described. Because of that, TCON
> documentation is extended.
>
> A83T features Synopsys DW HDMI controller with a custom PHY which looks
> like Synopsys Gen2 PHY with few additions. Since there is no
> documentation, needed properties were found out through experimentation
> and reading BSP code.
>
> At the end, example is added for newer SoCs, which feature DE2 and DW
> HDMI.
>
> Signed-off-by: Jernej Skrabec <jernej.skrabec@xxxxxxxx>
> ---
> .../bindings/display/sunxi/sun4i-drm.txt | 197 ++++++++++++++++++++-
> 1 file changed, 190 insertions(+), 7 deletions(-)
>
> diff --git a/Documentation/devicetree/bindings/display/sunxi/sun4i-drm.txt b/Documentation/devicetree/bindings/display/sunxi/sun4i-drm.txt
> index cd626ee1147a..4fb380f3e53d 100644
> --- a/Documentation/devicetree/bindings/display/sunxi/sun4i-drm.txt
> +++ b/Documentation/devicetree/bindings/display/sunxi/sun4i-drm.txt
> @@ -64,6 +64,52 @@ Required properties:
> first port should be the input endpoint. The second should be the
> output, usually to an HDMI connector.
>
> +DWC HDMI TX Encoder
> +-------------------
> +
> +The HDMI transmitter is a Synopsys DesignWare HDMI 1.4 TX controller IP
> +with Allwinner's own PHY IP. It supports audio and video outputs and CEC.
> +
> +These DT bindings follow the Synopsys DWC HDMI TX bindings defined in
> +Documentation/devicetree/bindings/display/bridge/dw_hdmi.txt with the
> +following device-specific properties.
> +
> +Required properties:
> +
> + - compatible: value must be one of:
> + * "allwinner,sun8i-a83t-dw-hdmi"
> + - reg: base address and size of memory-mapped region
> + - reg-io-width: See dw_hdmi.txt. Shall be 1.
> + - interrupts: HDMI interrupt number
> + - clocks: phandles to the clocks feeding the HDMI encoder
> + * iahb: the HDMI bus clock
> + * isfr: the HDMI register clock
> + - clock-names: the clock names mentioned above
> + - resets: phandle to the reset controller
> + - reset-names: must be "ctrl"
> + - phys: phandle to the DWC HDMI PHY
> + - phy-names: must be "phy"
> +
> + - ports: A ports node with endpoint definitions as defined in
> + Documentation/devicetree/bindings/media/video-interfaces.txt. The
> + first port should be the input endpoint. The second should be the
> + output, usually to an HDMI connector.
> +
> +DWC HDMI PHY
> +------------
> +
> +Required properties:
> + - compatible: value must be one of:
> + * allwinner,sun8i-a83t-hdmi-phy
> + - reg: base address and size of memory-mapped region
> + - clocks: phandles to the clocks feeding the HDMI PHY
> + * bus: the HDMI PHY interface clock
> + * mod: the HDMI PHY module clock
> + * tmds: TMDS clock
> + - clock-names: the clock names mentioned above
> + - resets: phandle to the reset controller driving the PHY
> + - reset-names: must be "phy"
> +
> TV Encoder
> ----------
>
> @@ -94,24 +140,23 @@ Required properties:
> * allwinner,sun7i-a20-tcon
> * allwinner,sun8i-a33-tcon
> * allwinner,sun8i-a83t-tcon-lcd
> + * allwinner,sun8i-a83t-tcon-tv
> * allwinner,sun8i-v3s-tcon
> - reg: base address and size of memory-mapped region
> - interrupts: interrupt associated to this IP
> - - clocks: phandles to the clocks feeding the TCON. Three are needed:
> + - clocks: phandles to the clocks feeding the TCON. One is needed:
> - 'ahb': the interface clocks
> - - 'tcon-ch0': The clock driving the TCON channel 0
Well, it didn't look right before saying 3 are needed, but listing 2.
However, you can't just change this as it affects all the other SoCs.
This should probably be a separate patch.
> - resets: phandles to the reset controllers driving the encoder
> - "lcd": the reset line for the TCON channel 0
>
> - clock-names: the clock names mentioned above
> - reset-names: the reset names mentioned above
> - - clock-output-names: Name of the pixel clock created
Why is this removed?
>
> - ports: A ports node with endpoint definitions as defined in
> Documentation/devicetree/bindings/media/video-interfaces.txt. The
> first port should be the input endpoint, the second one the output
>
> - The output may have multiple endpoints. The TCON has two channels,
> + The output may have multiple endpoints. TCON can have two channels,
Perhaps you should say "can have 1 or 2 channels".
> usually with the first channel being used for the panels interfaces
> (RGB, LVDS, etc.), and the second being used for the outputs that
> require another controller (TV Encoder, HDMI, etc.). The endpoints
> @@ -119,11 +164,16 @@ Required properties:
> channel the endpoint is associated to. If that property is not
> present, the endpoint number will be used as the channel number.
>
> +When TCON supports channel 0 (all TCONs except TV TCON on A83T), two
> +more clocks are needed:
> + - 'tcon-ch0': The clock driving the TCON channel 0
Looks like one clock to me.
> + - clock-output-names: Name of the pixel clock created
It's better to not move this, but just add what compatibles it does or
doesn't apply to.
> +
> On SoCs other than the A33 and V3s, there is one more clock required:
> - 'tcon-ch1': The clock driving the TCON channel 1
>
> -On SoCs that support LVDS (all SoCs but the A13, H3, H5 and V3s), you
> -need one more reset line:
> +When TCON support LVDS (all TCONs except TV TCON on A83T and those found
> +in A13, H3, H5 and V3s SoCs), you need one more reset line:
> - 'lvds': The reset line driving the LVDS logic
>
> And on the A23, A31, A31s and A33, you need one more clock line:
> @@ -226,6 +276,7 @@ supported.
> Required properties:
> - compatible: value must be one of:
> * allwinner,sun8i-a83t-de2-mixer-0
> + * allwinner,sun8i-a83t-de2-mixer-1
> * allwinner,sun8i-v3s-de2-mixer
> - reg: base address and size of the memory-mapped region.
> - clocks: phandles to the clocks feeding the mixer
> @@ -261,7 +312,7 @@ Required properties:
> - allwinner,pipelines: list of phandle to the display engine
> frontends (DE 1.0) or mixers (DE 2.0) available.
>
> -Example:
> +Example 1:
>
> panel: panel {
> compatible = "olimex,lcd-olinuxino-43-ts";
> @@ -460,3 +511,135 @@ display-engine {
> compatible = "allwinner,sun5i-a13-display-engine";
> allwinner,pipelines = <&fe0>;
> };
> +
> +Example 2:
Is this really different enough to need an example? Examples don't
need to enumerate all possible options. They are often wrong because
they don't compile on their own and that creates a maintenance burden.
Rob
_______________________________________________
dri-devel mailing list
dri-devel@xxxxxxxxxxxxxxxxxxxxx
https://lists.freedesktop.org/mailman/listinfo/dri-devel
