On 12.01.2018 17:25, Philippe Cornu wrote:
> The pixel clock is optional. When available, it offers a better
> preciseness for timing computations and allows to reduce the extra dsi
> bandwidth in burst mode (from ~20% to ~10-12%, hw platform dependent).
>
> Signed-off-by: Philippe Cornu <philippe.cornu@xxxxxx>
> ---
> Changes in v2: Improve px_clk probing in case of ENOENT dt returned value
> (thanks to Philipp Zabel & Andrzej Hajda comments)
>
> drivers/gpu/drm/bridge/synopsys/dw-mipi-dsi.c | 26 ++++++++++++++++++++------
> 1 file changed, 20 insertions(+), 6 deletions(-)
>
> diff --git a/drivers/gpu/drm/bridge/synopsys/dw-mipi-dsi.c b/drivers/gpu/drm/bridge/synopsys/dw-mipi-dsi.c
> index c39c7dce20ed..62fcff881b98 100644
> --- a/drivers/gpu/drm/bridge/synopsys/dw-mipi-dsi.c
> +++ b/drivers/gpu/drm/bridge/synopsys/dw-mipi-dsi.c
> @@ -225,6 +225,7 @@ struct dw_mipi_dsi {
> void __iomem *base;
>
> struct clk *pclk;
> + struct clk *px_clk;
>
> unsigned int lane_mbps; /* per lane */
> u32 channel;
> @@ -753,24 +754,28 @@ void dw_mipi_dsi_bridge_mode_set(struct drm_bridge *bridge,
> struct dw_mipi_dsi *dsi = bridge_to_dsi(bridge);
> const struct dw_mipi_dsi_phy_ops *phy_ops = dsi->plat_data->phy_ops;
> void *priv_data = dsi->plat_data->priv_data;
> + struct drm_display_mode px_clk_mode = *mode;
> int ret;
>
> clk_prepare_enable(dsi->pclk);
>
> - ret = phy_ops->get_lane_mbps(priv_data, mode, dsi->mode_flags,
> + if (dsi->px_clk)
> + px_clk_mode.clock = clk_get_rate(dsi->px_clk) / 1000;
> +
> + ret = phy_ops->get_lane_mbps(priv_data, &px_clk_mode, dsi->mode_flags,
> dsi->lanes, dsi->format, &dsi->lane_mbps);
> if (ret)
> DRM_DEBUG_DRIVER("Phy get_lane_mbps() failed\n");
>
> pm_runtime_get_sync(dsi->dev);
> dw_mipi_dsi_init(dsi);
> - dw_mipi_dsi_dpi_config(dsi, mode);
> + dw_mipi_dsi_dpi_config(dsi, &px_clk_mode);
> dw_mipi_dsi_packet_handler_config(dsi);
> dw_mipi_dsi_video_mode_config(dsi);
> - dw_mipi_dsi_video_packet_config(dsi, mode);
> + dw_mipi_dsi_video_packet_config(dsi, &px_clk_mode);
> dw_mipi_dsi_command_mode_config(dsi);
> - dw_mipi_dsi_line_timer_config(dsi, mode);
> - dw_mipi_dsi_vertical_timing_config(dsi, mode);
> + dw_mipi_dsi_line_timer_config(dsi, &px_clk_mode);
> + dw_mipi_dsi_vertical_timing_config(dsi, &px_clk_mode);
>
> dw_mipi_dsi_dphy_init(dsi);
> dw_mipi_dsi_dphy_timing_config(dsi);
> @@ -784,7 +789,7 @@ void dw_mipi_dsi_bridge_mode_set(struct drm_bridge *bridge,
>
> dw_mipi_dsi_dphy_enable(dsi);
>
> - dw_mipi_dsi_wait_for_two_frames(mode);
> + dw_mipi_dsi_wait_for_two_frames(&px_clk_mode);
>
> /* Switch to cmd mode for panel-bridge pre_enable & panel prepare */
> dw_mipi_dsi_set_mode(dsi, 0);
> @@ -878,6 +883,15 @@ __dw_mipi_dsi_probe(struct platform_device *pdev,
> return ERR_PTR(ret);
> }
>
> + dsi->px_clk = devm_clk_get(dev, "px_clk");
> + if (PTR_ERR(dsi->px_clk) == -ENOENT) {
> + dsi->px_clk = NULL;
> + } else if (IS_ERR(dsi->px_clk)) {
> + ret = PTR_ERR(dsi->px_clk);
> + dev_err(dev, "Unable to get optional px_clk: %d\n", ret);
> + dsi->px_clk = NULL;
> + }
> +
As I understand on fail you just log an error and continue?
The code could be slightly simplified, for example:
dsi->px_clk = devm_clk_get(dev, "px_clk");
if (IS_ERR(dsi->px_clk)) {
ret = PTR_ERR(dsi->px_clk);
if (ret != ENOENT)
dev_err(dev, "Unable to get optional px_clk: %d\n", ret);
dsi->px_clk = NULL;
}
With or without this change:
Reviewed-by: Andrzej Hajda <a.hajda@xxxxxxxxxxx>
--
Regards
Andrzej
> /*
> * Note that the reset was not defined in the initial device tree, so
> * we have to be prepared for it not being found.
_______________________________________________
dri-devel mailing list
dri-devel@xxxxxxxxxxxxxxxxxxxxx
https://lists.freedesktop.org/mailman/listinfo/dri-devel
