[PATCH 01/11] clk: sunxi-ng: Don't set k if width is 0 for nkmp plls

[Jernej Skrabec <jernej.skrabec@xxxxxxxx>]

For example, A83T have nmp plls which are modelled as nkmp plls. Since k
is not specified, it has offset 0, shift 0 and lowest value 1. This
means that LSB bit is always set to 1, which may change clock rate.

Fix that by applying k factor only if k width is greater than 0.

Signed-off-by: Jernej Skrabec <jernej.skrabec@xxxxxxxx>
---
 drivers/clk/sunxi-ng/ccu_nkmp.c | 21 +++++++++++++--------
 1 file changed, 13 insertions(+), 8 deletions(-)

diff --git a/drivers/clk/sunxi-ng/ccu_nkmp.c b/drivers/clk/sunxi-ng/ccu_nkmp.c
index e58c95787f94..709f528af2b3 100644
--- a/drivers/clk/sunxi-ng/ccu_nkmp.c
+++ b/drivers/clk/sunxi-ng/ccu_nkmp.c
@@ -81,7 +81,7 @@ static unsigned long ccu_nkmp_recalc_rate(struct clk_hw *hw,
 					unsigned long parent_rate)
 {
 	struct ccu_nkmp *nkmp = hw_to_ccu_nkmp(hw);
-	unsigned long n, m, k, p;
+	unsigned long n, m, k = 1, p;
 	u32 reg;
 
 	reg = readl(nkmp->common.base + nkmp->common.reg);
@@ -92,11 +92,13 @@ static unsigned long ccu_nkmp_recalc_rate(struct clk_hw *hw,
 	if (!n)
 		n++;
 
-	k = reg >> nkmp->k.shift;
-	k &= (1 << nkmp->k.width) - 1;
-	k += nkmp->k.offset;
-	if (!k)
-		k++;
+	if (nkmp->k.width) {
+		k = reg >> nkmp->k.shift;
+		k &= (1 << nkmp->k.width) - 1;
+		k += nkmp->k.offset;
+		if (!k)
+			k++;
+	}
 
 	m = reg >> nkmp->m.shift;
 	m &= (1 << nkmp->m.width) - 1;
@@ -153,12 +155,15 @@ static int ccu_nkmp_set_rate(struct clk_hw *hw, unsigned long rate,
 
 	reg = readl(nkmp->common.base + nkmp->common.reg);
 	reg &= ~GENMASK(nkmp->n.width + nkmp->n.shift - 1, nkmp->n.shift);
-	reg &= ~GENMASK(nkmp->k.width + nkmp->k.shift - 1, nkmp->k.shift);
+	if (nkmp->k.width)
+		reg &= ~GENMASK(nkmp->k.width + nkmp->k.shift - 1,
+				nkmp->k.shift);
 	reg &= ~GENMASK(nkmp->m.width + nkmp->m.shift - 1, nkmp->m.shift);
 	reg &= ~GENMASK(nkmp->p.width + nkmp->p.shift - 1, nkmp->p.shift);
 
 	reg |= (_nkmp.n - nkmp->n.offset) << nkmp->n.shift;
-	reg |= (_nkmp.k - nkmp->k.offset) << nkmp->k.shift;
+	if (nkmp->k.width)
+		reg |= (_nkmp.k - nkmp->k.offset) << nkmp->k.shift;
 	reg |= (_nkmp.m - nkmp->m.offset) << nkmp->m.shift;
 	reg |= ilog2(_nkmp.p) << nkmp->p.shift;
 
-- 
2.15.1

_______________________________________________
dri-devel mailing list
dri-devel@xxxxxxxxxxxxxxxxxxxxx
https://lists.freedesktop.org/mailman/listinfo/dri-devel