From: Alan Cox <alan@xxxxxxxxxxxxxxx>
Oaktrail (GMA600) is found on some tablet/slate PC type systems. It's a bit
different to the GMA500 but similar enough it makes sense to plug it into
the same driver.
Signed-off-by: Alan Cox <alan@xxxxxxxxxxxxxxx>
---
drivers/gpu/drm/gma500/oaktrail.h | 252 ++++++++
drivers/gpu/drm/gma500/oaktrail_crtc.c | 610 ++++++++++++++++++++
drivers/gpu/drm/gma500/oaktrail_device.c | 489 ++++++++++++++++
drivers/gpu/drm/gma500/oaktrail_hdmi.c | 852 ++++++++++++++++++++++++++++
drivers/gpu/drm/gma500/oaktrail_hdmi_i2c.c | 327 +++++++++++
drivers/gpu/drm/gma500/oaktrail_lvds.c | 406 +++++++++++++
6 files changed, 2936 insertions(+), 0 deletions(-)
create mode 100644 drivers/gpu/drm/gma500/oaktrail.h
create mode 100644 drivers/gpu/drm/gma500/oaktrail_crtc.c
create mode 100644 drivers/gpu/drm/gma500/oaktrail_device.c
create mode 100644 drivers/gpu/drm/gma500/oaktrail_hdmi.c
create mode 100644 drivers/gpu/drm/gma500/oaktrail_hdmi_i2c.c
create mode 100644 drivers/gpu/drm/gma500/oaktrail_lvds.c
diff --git a/drivers/gpu/drm/gma500/oaktrail.h b/drivers/gpu/drm/gma500/oaktrail.h
new file mode 100644
index 0000000..2da1f36
--- /dev/null
+++ b/drivers/gpu/drm/gma500/oaktrail.h
@@ -0,0 +1,252 @@
+/**************************************************************************
+ * Copyright (c) 2007-2011, Intel Corporation.
+ * All Rights Reserved.
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms and conditions of the GNU General Public License,
+ * version 2, as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope it will be useful, but WITHOUT
+ * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+ * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for
+ * more details.
+ *
+ * You should have received a copy of the GNU General Public License along with
+ * this program; if not, write to the Free Software Foundation, Inc.,
+ * 51 Franklin St - Fifth Floor, Boston, MA 02110-1301 USA.
+ *
+ **************************************************************************/
+
+/* MID device specific descriptors */
+
+struct oaktrail_vbt {
+ s8 signature[4]; /*4 bytes,"$GCT" */
+ u8 revision;
+ u8 size;
+ u8 checksum;
+ void *oaktrail_gct;
+} __packed;
+
+struct oaktrail_timing_info {
+ u16 pixel_clock;
+ u8 hactive_lo;
+ u8 hblank_lo;
+ u8 hblank_hi:4;
+ u8 hactive_hi:4;
+ u8 vactive_lo;
+ u8 vblank_lo;
+ u8 vblank_hi:4;
+ u8 vactive_hi:4;
+ u8 hsync_offset_lo;
+ u8 hsync_pulse_width_lo;
+ u8 vsync_pulse_width_lo:4;
+ u8 vsync_offset_lo:4;
+ u8 vsync_pulse_width_hi:2;
+ u8 vsync_offset_hi:2;
+ u8 hsync_pulse_width_hi:2;
+ u8 hsync_offset_hi:2;
+ u8 width_mm_lo;
+ u8 height_mm_lo;
+ u8 height_mm_hi:4;
+ u8 width_mm_hi:4;
+ u8 hborder;
+ u8 vborder;
+ u8 unknown0:1;
+ u8 hsync_positive:1;
+ u8 vsync_positive:1;
+ u8 separate_sync:2;
+ u8 stereo:1;
+ u8 unknown6:1;
+ u8 interlaced:1;
+} __packed;
+
+struct gct_r10_timing_info {
+ u16 pixel_clock;
+ u32 hactive_lo:8;
+ u32 hactive_hi:4;
+ u32 hblank_lo:8;
+ u32 hblank_hi:4;
+ u32 hsync_offset_lo:8;
+ u16 hsync_offset_hi:2;
+ u16 hsync_pulse_width_lo:8;
+ u16 hsync_pulse_width_hi:2;
+ u16 hsync_positive:1;
+ u16 rsvd_1:3;
+ u8 vactive_lo:8;
+ u16 vactive_hi:4;
+ u16 vblank_lo:8;
+ u16 vblank_hi:4;
+ u16 vsync_offset_lo:4;
+ u16 vsync_offset_hi:2;
+ u16 vsync_pulse_width_lo:4;
+ u16 vsync_pulse_width_hi:2;
+ u16 vsync_positive:1;
+ u16 rsvd_2:3;
+} __packed;
+
+struct oaktrail_panel_descriptor_v1 {
+ u32 Panel_Port_Control; /* 1 dword, Register 0x61180 if LVDS */
+ /* 0x61190 if MIPI */
+ u32 Panel_Power_On_Sequencing;/*1 dword,Register 0x61208,*/
+ u32 Panel_Power_Off_Sequencing;/*1 dword,Register 0x6120C,*/
+ u32 Panel_Power_Cycle_Delay_and_Reference_Divisor;/* 1 dword */
+ /* Register 0x61210 */
+ struct oaktrail_timing_info DTD;/*18 bytes, Standard definition */
+ u16 Panel_Backlight_Inverter_Descriptor;/* 16 bits, as follows */
+ /* Bit 0, Frequency, 15 bits,0 - 32767Hz */
+ /* Bit 15, Polarity, 1 bit, 0: Normal, 1: Inverted */
+ u16 Panel_MIPI_Display_Descriptor;
+ /*16 bits, Defined as follows: */
+ /* if MIPI, 0x0000 if LVDS */
+ /* Bit 0, Type, 2 bits, */
+ /* 0: Type-1, */
+ /* 1: Type-2, */
+ /* 2: Type-3, */
+ /* 3: Type-4 */
+ /* Bit 2, Pixel Format, 4 bits */
+ /* Bit0: 16bpp (not supported in LNC), */
+ /* Bit1: 18bpp loosely packed, */
+ /* Bit2: 18bpp packed, */
+ /* Bit3: 24bpp */
+ /* Bit 6, Reserved, 2 bits, 00b */
+ /* Bit 8, Minimum Supported Frame Rate, 6 bits, 0 - 63Hz */
+ /* Bit 14, Reserved, 2 bits, 00b */
+} __packed;
+
+struct oaktrail_panel_descriptor_v2 {
+ u32 Panel_Port_Control; /* 1 dword, Register 0x61180 if LVDS */
+ /* 0x61190 if MIPI */
+ u32 Panel_Power_On_Sequencing;/*1 dword,Register 0x61208,*/
+ u32 Panel_Power_Off_Sequencing;/*1 dword,Register 0x6120C,*/
+ u8 Panel_Power_Cycle_Delay_and_Reference_Divisor;/* 1 byte */
+ /* Register 0x61210 */
+ struct oaktrail_timing_info DTD;/*18 bytes, Standard definition */
+ u16 Panel_Backlight_Inverter_Descriptor;/*16 bits, as follows*/
+ /*Bit 0, Frequency, 16 bits, 0 - 32767Hz*/
+ u8 Panel_Initial_Brightness;/* [7:0] 0 - 100% */
+ /*Bit 7, Polarity, 1 bit,0: Normal, 1: Inverted*/
+ u16 Panel_MIPI_Display_Descriptor;
+ /*16 bits, Defined as follows: */
+ /* if MIPI, 0x0000 if LVDS */
+ /* Bit 0, Type, 2 bits, */
+ /* 0: Type-1, */
+ /* 1: Type-2, */
+ /* 2: Type-3, */
+ /* 3: Type-4 */
+ /* Bit 2, Pixel Format, 4 bits */
+ /* Bit0: 16bpp (not supported in LNC), */
+ /* Bit1: 18bpp loosely packed, */
+ /* Bit2: 18bpp packed, */
+ /* Bit3: 24bpp */
+ /* Bit 6, Reserved, 2 bits, 00b */
+ /* Bit 8, Minimum Supported Frame Rate, 6 bits, 0 - 63Hz */
+ /* Bit 14, Reserved, 2 bits, 00b */
+} __packed;
+
+union oaktrail_panel_rx {
+ struct {
+ u16 NumberOfLanes:2; /*Num of Lanes, 2 bits,0 = 1 lane,*/
+ /* 1 = 2 lanes, 2 = 3 lanes, 3 = 4 lanes. */
+ u16 MaxLaneFreq:3; /* 0: 100MHz, 1: 200MHz, 2: 300MHz, */
+ /*3: 400MHz, 4: 500MHz, 5: 600MHz, 6: 700MHz, 7: 800MHz.*/
+ u16 SupportedVideoTransferMode:2; /*0: Non-burst only */
+ /* 1: Burst and non-burst */
+ /* 2/3: Reserved */
+ u16 HSClkBehavior:1; /*0: Continuous, 1: Non-continuous*/
+ u16 DuoDisplaySupport:1; /*1 bit,0: No, 1: Yes*/
+ u16 ECC_ChecksumCapabilities:1;/*1 bit,0: No, 1: Yes*/
+ u16 BidirectionalCommunication:1;/*1 bit,0: No, 1: Yes */
+ u16 Rsvd:5;/*5 bits,00000b */
+ } panelrx;
+ u16 panel_receiver;
+} __packed;
+
+struct oaktrail_gct_v1 {
+ union { /*8 bits,Defined as follows: */
+ struct {
+ u8 PanelType:4; /*4 bits, Bit field for panels*/
+ /* 0 - 3: 0 = LVDS, 1 = MIPI*/
+ /*2 bits,Specifies which of the*/
+ u8 BootPanelIndex:2;
+ /* 4 panels to use by default*/
+ u8 BootMIPI_DSI_RxIndex:2;/*Specifies which of*/
+ /* the 4 MIPI DSI receivers to use*/
+ } PD;
+ u8 PanelDescriptor;
+ };
+ struct oaktrail_panel_descriptor_v1 panel[4];/*panel descrs,38 bytes each*/
+ union oaktrail_panel_rx panelrx[4]; /* panel receivers*/
+} __packed;
+
+struct oaktrail_gct_v2 {
+ union { /*8 bits,Defined as follows: */
+ struct {
+ u8 PanelType:4; /*4 bits, Bit field for panels*/
+ /* 0 - 3: 0 = LVDS, 1 = MIPI*/
+ /*2 bits,Specifies which of the*/
+ u8 BootPanelIndex:2;
+ /* 4 panels to use by default*/
+ u8 BootMIPI_DSI_RxIndex:2;/*Specifies which of*/
+ /* the 4 MIPI DSI receivers to use*/
+ } PD;
+ u8 PanelDescriptor;
+ };
+ struct oaktrail_panel_descriptor_v2 panel[4];/*panel descrs,38 bytes each*/
+ union oaktrail_panel_rx panelrx[4]; /* panel receivers*/
+} __packed;
+
+struct oaktrail_gct_data {
+ u8 bpi; /* boot panel index, number of panel used during boot */
+ u8 pt; /* panel type, 4 bit field, 0=lvds, 1=mipi */
+ struct oaktrail_timing_info DTD; /* timing info for the selected panel */
+ u32 Panel_Port_Control;
+ u32 PP_On_Sequencing;/*1 dword,Register 0x61208,*/
+ u32 PP_Off_Sequencing;/*1 dword,Register 0x6120C,*/
+ u32 PP_Cycle_Delay;
+ u16 Panel_Backlight_Inverter_Descriptor;
+ u16 Panel_MIPI_Display_Descriptor;
+} __packed;
+
+#define MODE_SETTING_IN_CRTC 0x1
+#define MODE_SETTING_IN_ENCODER 0x2
+#define MODE_SETTING_ON_GOING 0x3
+#define MODE_SETTING_IN_DSR 0x4
+#define MODE_SETTING_ENCODER_DONE 0x8
+
+#define GCT_R10_HEADER_SIZE 16
+#define GCT_R10_DISPLAY_DESC_SIZE 28
+
+/*
+ * Moorestown HDMI interfaces
+ */
+
+struct oaktrail_hdmi_dev {
+ struct pci_dev *dev;
+ void __iomem *regs;
+ unsigned int mmio, mmio_len;
+ int dpms_mode;
+ struct hdmi_i2c_dev *i2c_dev;
+
+ /* register state */
+ u32 saveDPLL_CTRL;
+ u32 saveDPLL_DIV_CTRL;
+ u32 saveDPLL_ADJUST;
+ u32 saveDPLL_UPDATE;
+ u32 saveDPLL_CLK_ENABLE;
+ u32 savePCH_HTOTAL_B;
+ u32 savePCH_HBLANK_B;
+ u32 savePCH_HSYNC_B;
+ u32 savePCH_VTOTAL_B;
+ u32 savePCH_VBLANK_B;
+ u32 savePCH_VSYNC_B;
+ u32 savePCH_PIPEBCONF;
+ u32 savePCH_PIPEBSRC;
+};
+
+extern void oaktrail_hdmi_setup(struct drm_device *dev);
+extern void oaktrail_hdmi_teardown(struct drm_device *dev);
+extern int oaktrail_hdmi_i2c_init(struct pci_dev *dev);
+extern void oaktrail_hdmi_i2c_exit(struct pci_dev *dev);
+extern void oaktrail_hdmi_save(struct drm_device *dev);
+extern void oaktrail_hdmi_restore(struct drm_device *dev);
+extern void oaktrail_hdmi_init(struct drm_device *dev, struct psb_intel_mode_device *mode_dev);
diff --git a/drivers/gpu/drm/gma500/oaktrail_crtc.c b/drivers/gpu/drm/gma500/oaktrail_crtc.c
new file mode 100644
index 0000000..7f9c791
--- /dev/null
+++ b/drivers/gpu/drm/gma500/oaktrail_crtc.c
@@ -0,0 +1,610 @@
+/*
+ * Copyright © 2009 Intel Corporation
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms and conditions of the GNU General Public License,
+ * version 2, as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope it will be useful, but WITHOUT
+ * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+ * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for
+ * more details.
+ *
+ * You should have received a copy of the GNU General Public License along with
+ * this program; if not, write to the Free Software Foundation, Inc.,
+ * 51 Franklin St - Fifth Floor, Boston, MA 02110-1301 USA.
+ */
+
+#include <linux/i2c.h>
+#include <linux/pm_runtime.h>
+
+#include <drm/drmP.h>
+#include "framebuffer.h"
+#include "psb_drv.h"
+#include "psb_intel_drv.h"
+#include "psb_intel_reg.h"
+#include "psb_intel_display.h"
+#include "power.h"
+
+struct psb_intel_range_t {
+ int min, max;
+};
+
+struct oaktrail_limit_t {
+ struct psb_intel_range_t dot, m, p1;
+};
+
+struct oaktrail_clock_t {
+ /* derived values */
+ int dot;
+ int m;
+ int p1;
+};
+
+#define MRST_LIMIT_LVDS_100L 0
+#define MRST_LIMIT_LVDS_83 1
+#define MRST_LIMIT_LVDS_100 2
+
+#define MRST_DOT_MIN 19750
+#define MRST_DOT_MAX 120000
+#define MRST_M_MIN_100L 20
+#define MRST_M_MIN_100 10
+#define MRST_M_MIN_83 12
+#define MRST_M_MAX_100L 34
+#define MRST_M_MAX_100 17
+#define MRST_M_MAX_83 20
+#define MRST_P1_MIN 2
+#define MRST_P1_MAX_0 7
+#define MRST_P1_MAX_1 8
+
+static const struct oaktrail_limit_t oaktrail_limits[] = {
+ { /* MRST_LIMIT_LVDS_100L */
+ .dot = {.min = MRST_DOT_MIN, .max = MRST_DOT_MAX},
+ .m = {.min = MRST_M_MIN_100L, .max = MRST_M_MAX_100L},
+ .p1 = {.min = MRST_P1_MIN, .max = MRST_P1_MAX_1},
+ },
+ { /* MRST_LIMIT_LVDS_83L */
+ .dot = {.min = MRST_DOT_MIN, .max = MRST_DOT_MAX},
+ .m = {.min = MRST_M_MIN_83, .max = MRST_M_MAX_83},
+ .p1 = {.min = MRST_P1_MIN, .max = MRST_P1_MAX_0},
+ },
+ { /* MRST_LIMIT_LVDS_100 */
+ .dot = {.min = MRST_DOT_MIN, .max = MRST_DOT_MAX},
+ .m = {.min = MRST_M_MIN_100, .max = MRST_M_MAX_100},
+ .p1 = {.min = MRST_P1_MIN, .max = MRST_P1_MAX_1},
+ },
+};
+
+#define MRST_M_MIN 10
+static const u32 oaktrail_m_converts[] = {
+ 0x2B, 0x15, 0x2A, 0x35, 0x1A, 0x0D, 0x26, 0x33, 0x19, 0x2C,
+ 0x36, 0x3B, 0x1D, 0x2E, 0x37, 0x1B, 0x2D, 0x16, 0x0B, 0x25,
+ 0x12, 0x09, 0x24, 0x32, 0x39, 0x1c,
+};
+
+static const struct oaktrail_limit_t *oaktrail_limit(struct drm_crtc *crtc)
+{
+ const struct oaktrail_limit_t *limit = NULL;
+ struct drm_device *dev = crtc->dev;
+ struct drm_psb_private *dev_priv = dev->dev_private;
+
+ if (psb_intel_pipe_has_type(crtc, INTEL_OUTPUT_LVDS)
+ || psb_intel_pipe_has_type(crtc, INTEL_OUTPUT_MIPI)) {
+ switch (dev_priv->core_freq) {
+ case 100:
+ limit = &oaktrail_limits[MRST_LIMIT_LVDS_100L];
+ break;
+ case 166:
+ limit = &oaktrail_limits[MRST_LIMIT_LVDS_83];
+ break;
+ case 200:
+ limit = &oaktrail_limits[MRST_LIMIT_LVDS_100];
+ break;
+ }
+ } else {
+ limit = NULL;
+ dev_err(dev->dev, "oaktrail_limit Wrong display type.\n");
+ }
+
+ return limit;
+}
+
+/** Derive the pixel clock for the given refclk and divisors for 8xx chips. */
+static void oaktrail_clock(int refclk, struct oaktrail_clock_t *clock)
+{
+ clock->dot = (refclk * clock->m) / (14 * clock->p1);
+}
+
+void mrstPrintPll(char *prefix, struct oaktrail_clock_t *clock)
+{
+ pr_debug("%s: dotclock = %d, m = %d, p1 = %d.\n",
+ prefix, clock->dot, clock->m, clock->p1);
+}
+
+/**
+ * Returns a set of divisors for the desired target clock with the given refclk,
+ * or FALSE. Divisor values are the actual divisors for
+ */
+static bool
+mrstFindBestPLL(struct drm_crtc *crtc, int target, int refclk,
+ struct oaktrail_clock_t *best_clock)
+{
+ struct oaktrail_clock_t clock;
+ const struct oaktrail_limit_t *limit = oaktrail_limit(crtc);
+ int err = target;
+
+ memset(best_clock, 0, sizeof(*best_clock));
+
+ for (clock.m = limit->m.min; clock.m <= limit->m.max; clock.m++) {
+ for (clock.p1 = limit->p1.min; clock.p1 <= limit->p1.max;
+ clock.p1++) {
+ int this_err;
+
+ oaktrail_clock(refclk, &clock);
+
+ this_err = abs(clock.dot - target);
+ if (this_err < err) {
+ *best_clock = clock;
+ err = this_err;
+ }
+ }
+ }
+ dev_dbg(crtc->dev->dev, "mrstFindBestPLL err = %d.\n", err);
+ return err != target;
+}
+
+/**
+ * Sets the power management mode of the pipe and plane.
+ *
+ * This code should probably grow support for turning the cursor off and back
+ * on appropriately at the same time as we're turning the pipe off/on.
+ */
+static void oaktrail_crtc_dpms(struct drm_crtc *crtc, int mode)
+{
+ struct drm_device *dev = crtc->dev;
+ struct psb_intel_crtc *psb_intel_crtc = to_psb_intel_crtc(crtc);
+ int pipe = psb_intel_crtc->pipe;
+ int dpll_reg = (pipe == 0) ? MRST_DPLL_A : DPLL_B;
+ int dspcntr_reg = (pipe == 0) ? DSPACNTR : DSPBCNTR;
+ int dspbase_reg = (pipe == 0) ? MRST_DSPABASE : DSPBBASE;
+ int pipeconf_reg = (pipe == 0) ? PIPEACONF : PIPEBCONF;
+ u32 temp;
+ bool enabled;
+
+ if (!gma_power_begin(dev, true))
+ return;
+
+ /* XXX: When our outputs are all unaware of DPMS modes other than off
+ * and on, we should map those modes to DRM_MODE_DPMS_OFF in the CRTC.
+ */
+ switch (mode) {
+ case DRM_MODE_DPMS_ON:
+ case DRM_MODE_DPMS_STANDBY:
+ case DRM_MODE_DPMS_SUSPEND:
+ /* Enable the DPLL */
+ temp = REG_READ(dpll_reg);
+ if ((temp & DPLL_VCO_ENABLE) == 0) {
+ REG_WRITE(dpll_reg, temp);
+ REG_READ(dpll_reg);
+ /* Wait for the clocks to stabilize. */
+ udelay(150);
+ REG_WRITE(dpll_reg, temp | DPLL_VCO_ENABLE);
+ REG_READ(dpll_reg);
+ /* Wait for the clocks to stabilize. */
+ udelay(150);
+ REG_WRITE(dpll_reg, temp | DPLL_VCO_ENABLE);
+ REG_READ(dpll_reg);
+ /* Wait for the clocks to stabilize. */
+ udelay(150);
+ }
+ /* Enable the pipe */
+ temp = REG_READ(pipeconf_reg);
+ if ((temp & PIPEACONF_ENABLE) == 0)
+ REG_WRITE(pipeconf_reg, temp | PIPEACONF_ENABLE);
+ /* Enable the plane */
+ temp = REG_READ(dspcntr_reg);
+ if ((temp & DISPLAY_PLANE_ENABLE) == 0) {
+ REG_WRITE(dspcntr_reg,
+ temp | DISPLAY_PLANE_ENABLE);
+ /* Flush the plane changes */
+ REG_WRITE(dspbase_reg, REG_READ(dspbase_reg));
+ }
+
+ psb_intel_crtc_load_lut(crtc);
+
+ /* Give the overlay scaler a chance to enable
+ if it's on this pipe */
+ /* psb_intel_crtc_dpms_video(crtc, true); TODO */
+ break;
+ case DRM_MODE_DPMS_OFF:
+ /* Give the overlay scaler a chance to disable
+ * if it's on this pipe */
+ /* psb_intel_crtc_dpms_video(crtc, FALSE); TODO */
+
+ /* Disable the VGA plane that we never use */
+ REG_WRITE(VGACNTRL, VGA_DISP_DISABLE);
+ /* Disable display plane */
+ temp = REG_READ(dspcntr_reg);
+ if ((temp & DISPLAY_PLANE_ENABLE) != 0) {
+ REG_WRITE(dspcntr_reg,
+ temp & ~DISPLAY_PLANE_ENABLE);
+ /* Flush the plane changes */
+ REG_WRITE(dspbase_reg, REG_READ(dspbase_reg));
+ REG_READ(dspbase_reg);
+ }
+
+ /* Next, disable display pipes */
+ temp = REG_READ(pipeconf_reg);
+ if ((temp & PIPEACONF_ENABLE) != 0) {
+ REG_WRITE(pipeconf_reg, temp & ~PIPEACONF_ENABLE);
+ REG_READ(pipeconf_reg);
+ }
+ /* Wait for for the pipe disable to take effect. */
+ psb_intel_wait_for_vblank(dev);
+
+ temp = REG_READ(dpll_reg);
+ if ((temp & DPLL_VCO_ENABLE) != 0) {
+ REG_WRITE(dpll_reg, temp & ~DPLL_VCO_ENABLE);
+ REG_READ(dpll_reg);
+ }
+
+ /* Wait for the clocks to turn off. */
+ udelay(150);
+ break;
+ }
+
+ enabled = crtc->enabled && mode != DRM_MODE_DPMS_OFF;
+
+ /*Set FIFO Watermarks*/
+ REG_WRITE(DSPARB, 0x3FFF);
+ REG_WRITE(DSPFW1, 0x3F88080A);
+ REG_WRITE(DSPFW2, 0x0b060808);
+ REG_WRITE(DSPFW3, 0x0);
+ REG_WRITE(DSPFW4, 0x08030404);
+ REG_WRITE(DSPFW5, 0x04040404);
+ REG_WRITE(DSPFW6, 0x78);
+ REG_WRITE(0x70400, REG_READ(0x70400) | 0x4000);
+ /* Must write Bit 14 of the Chicken Bit Register */
+
+ gma_power_end(dev);
+}
+
+/**
+ * Return the pipe currently connected to the panel fitter,
+ * or -1 if the panel fitter is not present or not in use
+ */
+static int oaktrail_panel_fitter_pipe(struct drm_device *dev)
+{
+ u32 pfit_control;
+
+ pfit_control = REG_READ(PFIT_CONTROL);
+
+ /* See if the panel fitter is in use */
+ if ((pfit_control & PFIT_ENABLE) == 0)
+ return -1;
+ return (pfit_control >> 29) & 3;
+}
+
+static int oaktrail_crtc_mode_set(struct drm_crtc *crtc,
+ struct drm_display_mode *mode,
+ struct drm_display_mode *adjusted_mode,
+ int x, int y,
+ struct drm_framebuffer *old_fb)
+{
+ struct drm_device *dev = crtc->dev;
+ struct psb_intel_crtc *psb_intel_crtc = to_psb_intel_crtc(crtc);
+ struct drm_psb_private *dev_priv = dev->dev_private;
+ int pipe = psb_intel_crtc->pipe;
+ int fp_reg = (pipe == 0) ? MRST_FPA0 : FPB0;
+ int dpll_reg = (pipe == 0) ? MRST_DPLL_A : DPLL_B;
+ int dspcntr_reg = (pipe == 0) ? DSPACNTR : DSPBCNTR;
+ int pipeconf_reg = (pipe == 0) ? PIPEACONF : PIPEBCONF;
+ int htot_reg = (pipe == 0) ? HTOTAL_A : HTOTAL_B;
+ int hblank_reg = (pipe == 0) ? HBLANK_A : HBLANK_B;
+ int hsync_reg = (pipe == 0) ? HSYNC_A : HSYNC_B;
+ int vtot_reg = (pipe == 0) ? VTOTAL_A : VTOTAL_B;
+ int vblank_reg = (pipe == 0) ? VBLANK_A : VBLANK_B;
+ int vsync_reg = (pipe == 0) ? VSYNC_A : VSYNC_B;
+ int pipesrc_reg = (pipe == 0) ? PIPEASRC : PIPEBSRC;
+ int refclk = 0;
+ struct oaktrail_clock_t clock;
+ u32 dpll = 0, fp = 0, dspcntr, pipeconf;
+ bool ok, is_sdvo = false;
+ bool is_crt = false, is_lvds = false, is_tv = false;
+ bool is_mipi = false;
+ struct drm_mode_config *mode_config = &dev->mode_config;
+ struct psb_intel_output *psb_intel_output = NULL;
+ uint64_t scalingType = DRM_MODE_SCALE_FULLSCREEN;
+ struct drm_encoder *encoder;
+
+ if (!gma_power_begin(dev, true))
+ return 0;
+
+ memcpy(&psb_intel_crtc->saved_mode,
+ mode,
+ sizeof(struct drm_display_mode));
+ memcpy(&psb_intel_crtc->saved_adjusted_mode,
+ adjusted_mode,
+ sizeof(struct drm_display_mode));
+
+ list_for_each_entry(encoder, &mode_config->encoder_list, head) {
+
+ if (encoder->crtc != crtc)
+ continue;
+
+ psb_intel_output = enc_to_psb_intel_output(encoder);
+ switch (psb_intel_output->type) {
+ case INTEL_OUTPUT_LVDS:
+ is_lvds = true;
+ break;
+ case INTEL_OUTPUT_SDVO:
+ is_sdvo = true;
+ break;
+ case INTEL_OUTPUT_TVOUT:
+ is_tv = true;
+ break;
+ case INTEL_OUTPUT_ANALOG:
+ is_crt = true;
+ break;
+ case INTEL_OUTPUT_MIPI:
+ is_mipi = true;
+ break;
+ }
+ }
+
+ /* Disable the VGA plane that we never use */
+ REG_WRITE(VGACNTRL, VGA_DISP_DISABLE);
+
+ /* Disable the panel fitter if it was on our pipe */
+ if (oaktrail_panel_fitter_pipe(dev) == pipe)
+ REG_WRITE(PFIT_CONTROL, 0);
+
+ REG_WRITE(pipesrc_reg,
+ ((mode->crtc_hdisplay - 1) << 16) |
+ (mode->crtc_vdisplay - 1));
+
+ if (psb_intel_output)
+ drm_connector_property_get_value(&psb_intel_output->base,
+ dev->mode_config.scaling_mode_property, &scalingType);
+
+ if (scalingType == DRM_MODE_SCALE_NO_SCALE) {
+ /* Moorestown doesn't have register support for centering so
+ * we need to mess with the h/vblank and h/vsync start and
+ * ends to get centering */
+ int offsetX = 0, offsetY = 0;
+
+ offsetX = (adjusted_mode->crtc_hdisplay -
+ mode->crtc_hdisplay) / 2;
+ offsetY = (adjusted_mode->crtc_vdisplay -
+ mode->crtc_vdisplay) / 2;
+
+ REG_WRITE(htot_reg, (mode->crtc_hdisplay - 1) |
+ ((adjusted_mode->crtc_htotal - 1) << 16));
+ REG_WRITE(vtot_reg, (mode->crtc_vdisplay - 1) |
+ ((adjusted_mode->crtc_vtotal - 1) << 16));
+ REG_WRITE(hblank_reg,
+ (adjusted_mode->crtc_hblank_start - offsetX - 1) |
+ ((adjusted_mode->crtc_hblank_end - offsetX - 1) << 16));
+ REG_WRITE(hsync_reg,
+ (adjusted_mode->crtc_hsync_start - offsetX - 1) |
+ ((adjusted_mode->crtc_hsync_end - offsetX - 1) << 16));
+ REG_WRITE(vblank_reg,
+ (adjusted_mode->crtc_vblank_start - offsetY - 1) |
+ ((adjusted_mode->crtc_vblank_end - offsetY - 1) << 16));
+ REG_WRITE(vsync_reg,
+ (adjusted_mode->crtc_vsync_start - offsetY - 1) |
+ ((adjusted_mode->crtc_vsync_end - offsetY - 1) << 16));
+ } else {
+ REG_WRITE(htot_reg, (adjusted_mode->crtc_hdisplay - 1) |
+ ((adjusted_mode->crtc_htotal - 1) << 16));
+ REG_WRITE(vtot_reg, (adjusted_mode->crtc_vdisplay - 1) |
+ ((adjusted_mode->crtc_vtotal - 1) << 16));
+ REG_WRITE(hblank_reg, (adjusted_mode->crtc_hblank_start - 1) |
+ ((adjusted_mode->crtc_hblank_end - 1) << 16));
+ REG_WRITE(hsync_reg, (adjusted_mode->crtc_hsync_start - 1) |
+ ((adjusted_mode->crtc_hsync_end - 1) << 16));
+ REG_WRITE(vblank_reg, (adjusted_mode->crtc_vblank_start - 1) |
+ ((adjusted_mode->crtc_vblank_end - 1) << 16));
+ REG_WRITE(vsync_reg, (adjusted_mode->crtc_vsync_start - 1) |
+ ((adjusted_mode->crtc_vsync_end - 1) << 16));
+ }
+
+ /* Flush the plane changes */
+ {
+ struct drm_crtc_helper_funcs *crtc_funcs =
+ crtc->helper_private;
+ crtc_funcs->mode_set_base(crtc, x, y, old_fb);
+ }
+
+ /* setup pipeconf */
+ pipeconf = REG_READ(pipeconf_reg);
+
+ /* Set up the display plane register */
+ dspcntr = REG_READ(dspcntr_reg);
+ dspcntr |= DISPPLANE_GAMMA_ENABLE;
+
+ if (pipe == 0)
+ dspcntr |= DISPPLANE_SEL_PIPE_A;
+ else
+ dspcntr |= DISPPLANE_SEL_PIPE_B;
+
+ dev_priv->dspcntr = dspcntr |= DISPLAY_PLANE_ENABLE;
+ dev_priv->pipeconf = pipeconf |= PIPEACONF_ENABLE;
+
+ if (is_mipi)
+ goto oaktrail_crtc_mode_set_exit;
+
+ refclk = dev_priv->core_freq * 1000;
+
+ dpll = 0; /*BIT16 = 0 for 100MHz reference */
+
+ ok = mrstFindBestPLL(crtc, adjusted_mode->clock, refclk, &clock);
+
+ if (!ok) {
+ dev_dbg(dev->dev, "mrstFindBestPLL fail in oaktrail_crtc_mode_set.\n");
+ } else {
+ dev_dbg(dev->dev, "oaktrail_crtc_mode_set pixel clock = %d,"
+ "m = %x, p1 = %x.\n", clock.dot, clock.m,
+ clock.p1);
+ }
+
+ fp = oaktrail_m_converts[(clock.m - MRST_M_MIN)] << 8;
+
+ dpll |= DPLL_VGA_MODE_DIS;
+
+
+ dpll |= DPLL_VCO_ENABLE;
+
+ if (is_lvds)
+ dpll |= DPLLA_MODE_LVDS;
+ else
+ dpll |= DPLLB_MODE_DAC_SERIAL;
+
+ if (is_sdvo) {
+ int sdvo_pixel_multiply =
+ adjusted_mode->clock / mode->clock;
+
+ dpll |= DPLL_DVO_HIGH_SPEED;
+ dpll |=
+ (sdvo_pixel_multiply -
+ 1) << SDVO_MULTIPLIER_SHIFT_HIRES;
+ }
+
+
+ /* compute bitmask from p1 value */
+ dpll |= (1 << (clock.p1 - 2)) << 17;
+
+ dpll |= DPLL_VCO_ENABLE;
+
+ mrstPrintPll("chosen", &clock);
+
+ if (dpll & DPLL_VCO_ENABLE) {
+ REG_WRITE(fp_reg, fp);
+ REG_WRITE(dpll_reg, dpll & ~DPLL_VCO_ENABLE);
+ REG_READ(dpll_reg);
+ /* Check the DPLLA lock bit PIPEACONF[29] */
+ udelay(150);
+ }
+
+ REG_WRITE(fp_reg, fp);
+ REG_WRITE(dpll_reg, dpll);
+ REG_READ(dpll_reg);
+ /* Wait for the clocks to stabilize. */
+ udelay(150);
+
+ /* write it again -- the BIOS does, after all */
+ REG_WRITE(dpll_reg, dpll);
+ REG_READ(dpll_reg);
+ /* Wait for the clocks to stabilize. */
+ udelay(150);
+
+ REG_WRITE(pipeconf_reg, pipeconf);
+ REG_READ(pipeconf_reg);
+ psb_intel_wait_for_vblank(dev);
+
+ REG_WRITE(dspcntr_reg, dspcntr);
+ psb_intel_wait_for_vblank(dev);
+
+oaktrail_crtc_mode_set_exit:
+ gma_power_end(dev);
+ return 0;
+}
+
+static bool oaktrail_crtc_mode_fixup(struct drm_crtc *crtc,
+ struct drm_display_mode *mode,
+ struct drm_display_mode *adjusted_mode)
+{
+ return true;
+}
+
+int oaktrail_pipe_set_base(struct drm_crtc *crtc,
+ int x, int y, struct drm_framebuffer *old_fb)
+{
+ struct drm_device *dev = crtc->dev;
+ /* struct drm_i915_master_private *master_priv; */
+ struct psb_intel_crtc *psb_intel_crtc = to_psb_intel_crtc(crtc);
+ struct psb_framebuffer *psbfb = to_psb_fb(crtc->fb);
+ int pipe = psb_intel_crtc->pipe;
+ unsigned long start, offset;
+ /* FIXME: check if we need this surely MRST is pipe 0 only */
+ int dspbase = (pipe == 0 ? DSPALINOFF : DSPBBASE);
+ int dspsurf = (pipe == 0 ? DSPASURF : DSPBSURF);
+ int dspstride = (pipe == 0) ? DSPASTRIDE : DSPBSTRIDE;
+ int dspcntr_reg = (pipe == 0) ? DSPACNTR : DSPBCNTR;
+ u32 dspcntr;
+ int ret = 0;
+
+ /* no fb bound */
+ if (!crtc->fb) {
+ dev_dbg(dev->dev, "No FB bound\n");
+ return 0;
+ }
+
+ if (!gma_power_begin(dev, true))
+ return 0;
+
+ start = psbfb->gtt->offset;
+ offset = y * crtc->fb->pitch + x * (crtc->fb->bits_per_pixel / 8);
+
+ REG_WRITE(dspstride, crtc->fb->pitch);
+
+ dspcntr = REG_READ(dspcntr_reg);
+ dspcntr &= ~DISPPLANE_PIXFORMAT_MASK;
+
+ switch (crtc->fb->bits_per_pixel) {
+ case 8:
+ dspcntr |= DISPPLANE_8BPP;
+ break;
+ case 16:
+ if (crtc->fb->depth == 15)
+ dspcntr |= DISPPLANE_15_16BPP;
+ else
+ dspcntr |= DISPPLANE_16BPP;
+ break;
+ case 24:
+ case 32:
+ dspcntr |= DISPPLANE_32BPP_NO_ALPHA;
+ break;
+ default:
+ dev_err(dev->dev, "Unknown color depth\n");
+ ret = -EINVAL;
+ goto pipe_set_base_exit;
+ }
+ REG_WRITE(dspcntr_reg, dspcntr);
+
+ if (0 /* FIXMEAC - check what PSB needs */) {
+ REG_WRITE(dspbase, offset);
+ REG_READ(dspbase);
+ REG_WRITE(dspsurf, start);
+ REG_READ(dspsurf);
+ } else {
+ REG_WRITE(dspbase, start + offset);
+ REG_READ(dspbase);
+ }
+
+pipe_set_base_exit:
+ gma_power_end(dev);
+ return ret;
+}
+
+static void oaktrail_crtc_prepare(struct drm_crtc *crtc)
+{
+ struct drm_crtc_helper_funcs *crtc_funcs = crtc->helper_private;
+ crtc_funcs->dpms(crtc, DRM_MODE_DPMS_OFF);
+}
+
+static void oaktrail_crtc_commit(struct drm_crtc *crtc)
+{
+ struct drm_crtc_helper_funcs *crtc_funcs = crtc->helper_private;
+ crtc_funcs->dpms(crtc, DRM_MODE_DPMS_ON);
+}
+
+const struct drm_crtc_helper_funcs oaktrail_helper_funcs = {
+ .dpms = oaktrail_crtc_dpms,
+ .mode_fixup = oaktrail_crtc_mode_fixup,
+ .mode_set = oaktrail_crtc_mode_set,
+ .mode_set_base = oaktrail_pipe_set_base,
+ .prepare = oaktrail_crtc_prepare,
+ .commit = oaktrail_crtc_commit,
+};
+
diff --git a/drivers/gpu/drm/gma500/oaktrail_device.c b/drivers/gpu/drm/gma500/oaktrail_device.c
new file mode 100644
index 0000000..41c418f
--- /dev/null
+++ b/drivers/gpu/drm/gma500/oaktrail_device.c
@@ -0,0 +1,489 @@
+/**************************************************************************
+ * Copyright (c) 2011, Intel Corporation.
+ * All Rights Reserved.
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms and conditions of the GNU General Public License,
+ * version 2, as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope it will be useful, but WITHOUT
+ * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+ * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for
+ * more details.
+ *
+ * You should have received a copy of the GNU General Public License along with
+ * this program; if not, write to the Free Software Foundation, Inc.,
+ * 51 Franklin St - Fifth Floor, Boston, MA 02110-1301 USA.
+ *
+ **************************************************************************/
+
+#include <linux/backlight.h>
+#include <linux/module.h>
+#include <linux/dmi.h>
+#include <drm/drmP.h>
+#include <drm/drm.h>
+#include "psb_drm.h"
+#include "psb_drv.h"
+#include "psb_reg.h"
+#include "psb_intel_reg.h"
+#include <asm/mrst.h>
+#include <asm/intel_scu_ipc.h>
+#include "mid_bios.h"
+
+static int oaktrail_output_init(struct drm_device *dev)
+{
+ struct drm_psb_private *dev_priv = dev->dev_private;
+ if (dev_priv->iLVDS_enable)
+ oaktrail_lvds_init(dev, &dev_priv->mode_dev);
+ else
+ dev_err(dev->dev, "DSI is not supported\n");
+ if (dev_priv->hdmi_priv)
+ oaktrail_hdmi_init(dev, &dev_priv->mode_dev);
+ return 0;
+}
+
+/*
+ * Provide the low level interfaces for the Moorestown backlight
+ */
+
+#ifdef CONFIG_BACKLIGHT_CLASS_DEVICE
+
+#define MRST_BLC_MAX_PWM_REG_FREQ 0xFFFF
+#define BLC_PWM_PRECISION_FACTOR 100 /* 10000000 */
+#define BLC_PWM_FREQ_CALC_CONSTANT 32
+#define MHz 1000000
+#define BLC_ADJUSTMENT_MAX 100
+
+static struct backlight_device *oaktrail_backlight_device;
+static int oaktrail_brightness;
+
+static int oaktrail_set_brightness(struct backlight_device *bd)
+{
+ struct drm_device *dev = bl_get_data(oaktrail_backlight_device);
+ struct drm_psb_private *dev_priv = dev->dev_private;
+ int level = bd->props.brightness;
+ u32 blc_pwm_ctl;
+ u32 max_pwm_blc;
+
+ /* Percentage 1-100% being valid */
+ if (level < 1)
+ level = 1;
+
+ if (gma_power_begin(dev, 0)) {
+ /* Calculate and set the brightness value */
+ max_pwm_blc = REG_READ(BLC_PWM_CTL) >> 16;
+ blc_pwm_ctl = level * max_pwm_blc / 100;
+
+ /* Adjust the backlight level with the percent in
+ * dev_priv->blc_adj1;
+ */
+ blc_pwm_ctl = blc_pwm_ctl * dev_priv->blc_adj1;
+ blc_pwm_ctl = blc_pwm_ctl / 100;
+
+ /* Adjust the backlight level with the percent in
+ * dev_priv->blc_adj2;
+ */
+ blc_pwm_ctl = blc_pwm_ctl * dev_priv->blc_adj2;
+ blc_pwm_ctl = blc_pwm_ctl / 100;
+
+ /* force PWM bit on */
+ REG_WRITE(BLC_PWM_CTL2, (0x80000000 | REG_READ(BLC_PWM_CTL2)));
+ REG_WRITE(BLC_PWM_CTL, (max_pwm_blc << 16) | blc_pwm_ctl);
+ gma_power_end(dev);
+ }
+ oaktrail_brightness = level;
+ return 0;
+}
+
+static int oaktrail_get_brightness(struct backlight_device *bd)
+{
+ /* return locally cached var instead of HW read (due to DPST etc.) */
+ /* FIXME: ideally return actual value in case firmware fiddled with
+ it */
+ return oaktrail_brightness;
+}
+
+static int device_backlight_init(struct drm_device *dev)
+{
+ struct drm_psb_private *dev_priv = dev->dev_private;
+ unsigned long core_clock;
+ u16 bl_max_freq;
+ uint32_t value;
+ uint32_t blc_pwm_precision_factor;
+
+ dev_priv->blc_adj1 = BLC_ADJUSTMENT_MAX;
+ dev_priv->blc_adj2 = BLC_ADJUSTMENT_MAX;
+ bl_max_freq = 256;
+ /* this needs to be set elsewhere */
+ blc_pwm_precision_factor = BLC_PWM_PRECISION_FACTOR;
+
+ core_clock = dev_priv->core_freq;
+
+ value = (core_clock * MHz) / BLC_PWM_FREQ_CALC_CONSTANT;
+ value *= blc_pwm_precision_factor;
+ value /= bl_max_freq;
+ value /= blc_pwm_precision_factor;
+
+ if (value > (unsigned long long)MRST_BLC_MAX_PWM_REG_FREQ)
+ return -ERANGE;
+
+ if (gma_power_begin(dev, false)) {
+ REG_WRITE(BLC_PWM_CTL2, (0x80000000 | REG_READ(BLC_PWM_CTL2)));
+ REG_WRITE(BLC_PWM_CTL, value | (value << 16));
+ gma_power_end(dev);
+ }
+ return 0;
+}
+
+static const struct backlight_ops oaktrail_ops = {
+ .get_brightness = oaktrail_get_brightness,
+ .update_status = oaktrail_set_brightness,
+};
+
+int oaktrail_backlight_init(struct drm_device *dev)
+{
+ struct drm_psb_private *dev_priv = dev->dev_private;
+ int ret;
+ struct backlight_properties props;
+
+ memset(&props, 0, sizeof(struct backlight_properties));
+ props.max_brightness = 100;
+ props.type = BACKLIGHT_PLATFORM;
+
+ oaktrail_backlight_device = backlight_device_register("oaktrail-bl",
+ NULL, (void *)dev, &oaktrail_ops, &props);
+
+ if (IS_ERR(oaktrail_backlight_device))
+ return PTR_ERR(oaktrail_backlight_device);
+
+ ret = device_backlight_init(dev);
+ if (ret < 0) {
+ backlight_device_unregister(oaktrail_backlight_device);
+ return ret;
+ }
+ oaktrail_backlight_device->props.brightness = 100;
+ oaktrail_backlight_device->props.max_brightness = 100;
+ backlight_update_status(oaktrail_backlight_device);
+ dev_priv->backlight_device = oaktrail_backlight_device;
+ return 0;
+}
+
+#endif
+
+/*
+ * Provide the Moorestown specific chip logic and low level methods
+ * for power management
+ */
+
+static void oaktrail_init_pm(struct drm_device *dev)
+{
+}
+
+/**
+ * oaktrail_save_display_registers - save registers lost on suspend
+ * @dev: our DRM device
+ *
+ * Save the state we need in order to be able to restore the interface
+ * upon resume from suspend
+ */
+static int oaktrail_save_display_registers(struct drm_device *dev)
+{
+ struct drm_psb_private *dev_priv = dev->dev_private;
+ int i;
+ u32 pp_stat;
+
+ /* Display arbitration control + watermarks */
+ dev_priv->saveDSPARB = PSB_RVDC32(DSPARB);
+ dev_priv->saveDSPFW1 = PSB_RVDC32(DSPFW1);
+ dev_priv->saveDSPFW2 = PSB_RVDC32(DSPFW2);
+ dev_priv->saveDSPFW3 = PSB_RVDC32(DSPFW3);
+ dev_priv->saveDSPFW4 = PSB_RVDC32(DSPFW4);
+ dev_priv->saveDSPFW5 = PSB_RVDC32(DSPFW5);
+ dev_priv->saveDSPFW6 = PSB_RVDC32(DSPFW6);
+ dev_priv->saveCHICKENBIT = PSB_RVDC32(DSPCHICKENBIT);
+
+ /* Pipe & plane A info */
+ dev_priv->savePIPEACONF = PSB_RVDC32(PIPEACONF);
+ dev_priv->savePIPEASRC = PSB_RVDC32(PIPEASRC);
+ dev_priv->saveFPA0 = PSB_RVDC32(MRST_FPA0);
+ dev_priv->saveFPA1 = PSB_RVDC32(MRST_FPA1);
+ dev_priv->saveDPLL_A = PSB_RVDC32(MRST_DPLL_A);
+ dev_priv->saveHTOTAL_A = PSB_RVDC32(HTOTAL_A);
+ dev_priv->saveHBLANK_A = PSB_RVDC32(HBLANK_A);
+ dev_priv->saveHSYNC_A = PSB_RVDC32(HSYNC_A);
+ dev_priv->saveVTOTAL_A = PSB_RVDC32(VTOTAL_A);
+ dev_priv->saveVBLANK_A = PSB_RVDC32(VBLANK_A);
+ dev_priv->saveVSYNC_A = PSB_RVDC32(VSYNC_A);
+ dev_priv->saveBCLRPAT_A = PSB_RVDC32(BCLRPAT_A);
+ dev_priv->saveDSPACNTR = PSB_RVDC32(DSPACNTR);
+ dev_priv->saveDSPASTRIDE = PSB_RVDC32(DSPASTRIDE);
+ dev_priv->saveDSPAADDR = PSB_RVDC32(DSPABASE);
+ dev_priv->saveDSPASURF = PSB_RVDC32(DSPASURF);
+ dev_priv->saveDSPALINOFF = PSB_RVDC32(DSPALINOFF);
+ dev_priv->saveDSPATILEOFF = PSB_RVDC32(DSPATILEOFF);
+
+ /* Save cursor regs */
+ dev_priv->saveDSPACURSOR_CTRL = PSB_RVDC32(CURACNTR);
+ dev_priv->saveDSPACURSOR_BASE = PSB_RVDC32(CURABASE);
+ dev_priv->saveDSPACURSOR_POS = PSB_RVDC32(CURAPOS);
+
+ /* Save palette (gamma) */
+ for (i = 0; i < 256; i++)
+ dev_priv->save_palette_a[i] = PSB_RVDC32(PALETTE_A + (i << 2));
+
+ if (dev_priv->hdmi_priv)
+ oaktrail_hdmi_save(dev);
+
+ /* Save performance state */
+ dev_priv->savePERF_MODE = PSB_RVDC32(MRST_PERF_MODE);
+
+ /* LVDS state */
+ dev_priv->savePP_CONTROL = PSB_RVDC32(PP_CONTROL);
+ dev_priv->savePFIT_PGM_RATIOS = PSB_RVDC32(PFIT_PGM_RATIOS);
+ dev_priv->savePFIT_AUTO_RATIOS = PSB_RVDC32(PFIT_AUTO_RATIOS);
+ dev_priv->saveBLC_PWM_CTL = PSB_RVDC32(BLC_PWM_CTL);
+ dev_priv->saveBLC_PWM_CTL2 = PSB_RVDC32(BLC_PWM_CTL2);
+ dev_priv->saveLVDS = PSB_RVDC32(LVDS);
+ dev_priv->savePFIT_CONTROL = PSB_RVDC32(PFIT_CONTROL);
+ dev_priv->savePP_ON_DELAYS = PSB_RVDC32(LVDSPP_ON);
+ dev_priv->savePP_OFF_DELAYS = PSB_RVDC32(LVDSPP_OFF);
+ dev_priv->savePP_DIVISOR = PSB_RVDC32(PP_CYCLE);
+
+ /* HW overlay */
+ dev_priv->saveOV_OVADD = PSB_RVDC32(OV_OVADD);
+ dev_priv->saveOV_OGAMC0 = PSB_RVDC32(OV_OGAMC0);
+ dev_priv->saveOV_OGAMC1 = PSB_RVDC32(OV_OGAMC1);
+ dev_priv->saveOV_OGAMC2 = PSB_RVDC32(OV_OGAMC2);
+ dev_priv->saveOV_OGAMC3 = PSB_RVDC32(OV_OGAMC3);
+ dev_priv->saveOV_OGAMC4 = PSB_RVDC32(OV_OGAMC4);
+ dev_priv->saveOV_OGAMC5 = PSB_RVDC32(OV_OGAMC5);
+
+ /* DPST registers */
+ dev_priv->saveHISTOGRAM_INT_CONTROL_REG =
+ PSB_RVDC32(HISTOGRAM_INT_CONTROL);
+ dev_priv->saveHISTOGRAM_LOGIC_CONTROL_REG =
+ PSB_RVDC32(HISTOGRAM_LOGIC_CONTROL);
+ dev_priv->savePWM_CONTROL_LOGIC = PSB_RVDC32(PWM_CONTROL_LOGIC);
+
+ if (dev_priv->iLVDS_enable) {
+ /* Shut down the panel */
+ PSB_WVDC32(0, PP_CONTROL);
+
+ do {
+ pp_stat = PSB_RVDC32(PP_STATUS);
+ } while (pp_stat & 0x80000000);
+
+ /* Turn off the plane */
+ PSB_WVDC32(0x58000000, DSPACNTR);
+ /* Trigger the plane disable */
+ PSB_WVDC32(0, DSPASURF);
+
+ /* Wait ~4 ticks */
+ msleep(4);
+
+ /* Turn off pipe */
+ PSB_WVDC32(0x0, PIPEACONF);
+ /* Wait ~8 ticks */
+ msleep(8);
+
+ /* Turn off PLLs */
+ PSB_WVDC32(0, MRST_DPLL_A);
+ }
+ return 0;
+}
+
+/**
+ * oaktrail_restore_display_registers - restore lost register state
+ * @dev: our DRM device
+ *
+ * Restore register state that was lost during suspend and resume.
+ */
+static int oaktrail_restore_display_registers(struct drm_device *dev)
+{
+ struct drm_psb_private *dev_priv = dev->dev_private;
+ u32 pp_stat;
+ int i;
+
+ /* Display arbitration + watermarks */
+ PSB_WVDC32(dev_priv->saveDSPARB, DSPARB);
+ PSB_WVDC32(dev_priv->saveDSPFW1, DSPFW1);
+ PSB_WVDC32(dev_priv->saveDSPFW2, DSPFW2);
+ PSB_WVDC32(dev_priv->saveDSPFW3, DSPFW3);
+ PSB_WVDC32(dev_priv->saveDSPFW4, DSPFW4);
+ PSB_WVDC32(dev_priv->saveDSPFW5, DSPFW5);
+ PSB_WVDC32(dev_priv->saveDSPFW6, DSPFW6);
+ PSB_WVDC32(dev_priv->saveCHICKENBIT, DSPCHICKENBIT);
+
+ /* Make sure VGA plane is off. it initializes to on after reset!*/
+ PSB_WVDC32(0x80000000, VGACNTRL);
+
+ /* set the plls */
+ PSB_WVDC32(dev_priv->saveFPA0, MRST_FPA0);
+ PSB_WVDC32(dev_priv->saveFPA1, MRST_FPA1);
+
+ /* Actually enable it */
+ PSB_WVDC32(dev_priv->saveDPLL_A, MRST_DPLL_A);
+ DRM_UDELAY(150);
+
+ /* Restore mode */
+ PSB_WVDC32(dev_priv->saveHTOTAL_A, HTOTAL_A);
+ PSB_WVDC32(dev_priv->saveHBLANK_A, HBLANK_A);
+ PSB_WVDC32(dev_priv->saveHSYNC_A, HSYNC_A);
+ PSB_WVDC32(dev_priv->saveVTOTAL_A, VTOTAL_A);
+ PSB_WVDC32(dev_priv->saveVBLANK_A, VBLANK_A);
+ PSB_WVDC32(dev_priv->saveVSYNC_A, VSYNC_A);
+ PSB_WVDC32(dev_priv->savePIPEASRC, PIPEASRC);
+ PSB_WVDC32(dev_priv->saveBCLRPAT_A, BCLRPAT_A);
+
+ /* Restore performance mode*/
+ PSB_WVDC32(dev_priv->savePERF_MODE, MRST_PERF_MODE);
+
+ /* Enable the pipe*/
+ if (dev_priv->iLVDS_enable)
+ PSB_WVDC32(dev_priv->savePIPEACONF, PIPEACONF);
+
+ /* Set up the plane*/
+ PSB_WVDC32(dev_priv->saveDSPALINOFF, DSPALINOFF);
+ PSB_WVDC32(dev_priv->saveDSPASTRIDE, DSPASTRIDE);
+ PSB_WVDC32(dev_priv->saveDSPATILEOFF, DSPATILEOFF);
+
+ /* Enable the plane */
+ PSB_WVDC32(dev_priv->saveDSPACNTR, DSPACNTR);
+ PSB_WVDC32(dev_priv->saveDSPASURF, DSPASURF);
+
+ /* Enable Cursor A */
+ PSB_WVDC32(dev_priv->saveDSPACURSOR_CTRL, CURACNTR);
+ PSB_WVDC32(dev_priv->saveDSPACURSOR_POS, CURAPOS);
+ PSB_WVDC32(dev_priv->saveDSPACURSOR_BASE, CURABASE);
+
+ /* Restore palette (gamma) */
+ for (i = 0; i < 256; i++)
+ PSB_WVDC32(dev_priv->save_palette_a[i], PALETTE_A + (i << 2));
+
+ if (dev_priv->hdmi_priv)
+ oaktrail_hdmi_restore(dev);
+
+ if (dev_priv->iLVDS_enable) {
+ PSB_WVDC32(dev_priv->saveBLC_PWM_CTL2, BLC_PWM_CTL2);
+ PSB_WVDC32(dev_priv->saveLVDS, LVDS); /*port 61180h*/
+ PSB_WVDC32(dev_priv->savePFIT_CONTROL, PFIT_CONTROL);
+ PSB_WVDC32(dev_priv->savePFIT_PGM_RATIOS, PFIT_PGM_RATIOS);
+ PSB_WVDC32(dev_priv->savePFIT_AUTO_RATIOS, PFIT_AUTO_RATIOS);
+ PSB_WVDC32(dev_priv->saveBLC_PWM_CTL, BLC_PWM_CTL);
+ PSB_WVDC32(dev_priv->savePP_ON_DELAYS, LVDSPP_ON);
+ PSB_WVDC32(dev_priv->savePP_OFF_DELAYS, LVDSPP_OFF);
+ PSB_WVDC32(dev_priv->savePP_DIVISOR, PP_CYCLE);
+ PSB_WVDC32(dev_priv->savePP_CONTROL, PP_CONTROL);
+ }
+
+ /* Wait for cycle delay */
+ do {
+ pp_stat = PSB_RVDC32(PP_STATUS);
+ } while (pp_stat & 0x08000000);
+
+ /* Wait for panel power up */
+ do {
+ pp_stat = PSB_RVDC32(PP_STATUS);
+ } while (pp_stat & 0x10000000);
+
+ /* Restore HW overlay */
+ PSB_WVDC32(dev_priv->saveOV_OVADD, OV_OVADD);
+ PSB_WVDC32(dev_priv->saveOV_OGAMC0, OV_OGAMC0);
+ PSB_WVDC32(dev_priv->saveOV_OGAMC1, OV_OGAMC1);
+ PSB_WVDC32(dev_priv->saveOV_OGAMC2, OV_OGAMC2);
+ PSB_WVDC32(dev_priv->saveOV_OGAMC3, OV_OGAMC3);
+ PSB_WVDC32(dev_priv->saveOV_OGAMC4, OV_OGAMC4);
+ PSB_WVDC32(dev_priv->saveOV_OGAMC5, OV_OGAMC5);
+
+ /* DPST registers */
+ PSB_WVDC32(dev_priv->saveHISTOGRAM_INT_CONTROL_REG,
+ HISTOGRAM_INT_CONTROL);
+ PSB_WVDC32(dev_priv->saveHISTOGRAM_LOGIC_CONTROL_REG,
+ HISTOGRAM_LOGIC_CONTROL);
+ PSB_WVDC32(dev_priv->savePWM_CONTROL_LOGIC, PWM_CONTROL_LOGIC);
+
+ return 0;
+}
+
+/**
+ * oaktrail_power_down - power down the display island
+ * @dev: our DRM device
+ *
+ * Power down the display interface of our device
+ */
+static int oaktrail_power_down(struct drm_device *dev)
+{
+ struct drm_psb_private *dev_priv = dev->dev_private;
+ u32 pwr_mask ;
+ u32 pwr_sts;
+
+ pwr_mask = PSB_PWRGT_DISPLAY_MASK;
+ outl(pwr_mask, dev_priv->ospm_base + PSB_PM_SSC);
+
+ while (true) {
+ pwr_sts = inl(dev_priv->ospm_base + PSB_PM_SSS);
+ if ((pwr_sts & pwr_mask) == pwr_mask)
+ break;
+ else
+ udelay(10);
+ }
+ return 0;
+}
+
+/*
+ * oaktrail_power_up
+ *
+ * Restore power to the specified island(s) (powergating)
+ */
+static int oaktrail_power_up(struct drm_device *dev)
+{
+ struct drm_psb_private *dev_priv = dev->dev_private;
+ u32 pwr_mask = PSB_PWRGT_DISPLAY_MASK;
+ u32 pwr_sts, pwr_cnt;
+
+ pwr_cnt = inl(dev_priv->ospm_base + PSB_PM_SSC);
+ pwr_cnt &= ~pwr_mask;
+ outl(pwr_cnt, (dev_priv->ospm_base + PSB_PM_SSC));
+
+ while (true) {
+ pwr_sts = inl(dev_priv->ospm_base + PSB_PM_SSS);
+ if ((pwr_sts & pwr_mask) == 0)
+ break;
+ else
+ udelay(10);
+ }
+ return 0;
+}
+
+
+static void oaktrail_teardown(struct drm_device *dev)
+{
+ oaktrail_hdmi_teardown(dev);
+}
+
+const struct psb_ops oaktrail_chip_ops = {
+ .name = "Oaktrail",
+ .accel_2d = 1,
+ .pipes = 2,
+ .crtcs = 2,
+ .sgx_offset = MRST_SGX_OFFSET,
+
+ .chip_setup = mid_chip_setup,
+ .chip_teardown = oaktrail_teardown,
+ .crtc_helper = &oaktrail_helper_funcs,
+ .crtc_funcs = &psb_intel_crtc_funcs,
+
+ .output_init = oaktrail_output_init,
+
+#ifdef CONFIG_BACKLIGHT_CLASS_DEVICE
+ .backlight_init = oaktrail_backlight_init,
+#endif
+
+ .init_pm = oaktrail_init_pm,
+ .save_regs = oaktrail_save_display_registers,
+ .restore_regs = oaktrail_restore_display_registers,
+ .power_down = oaktrail_power_down,
+ .power_up = oaktrail_power_up,
+
+ .i2c_bus = 1,
+};
diff --git a/drivers/gpu/drm/gma500/oaktrail_hdmi.c b/drivers/gpu/drm/gma500/oaktrail_hdmi.c
new file mode 100644
index 0000000..6f423c0
--- /dev/null
+++ b/drivers/gpu/drm/gma500/oaktrail_hdmi.c
@@ -0,0 +1,852 @@
+/*
+ * Copyright © 2010 Intel Corporation
+ *
+ * Permission is hereby granted, free of charge, to any person obtaining a
+ * copy of this software and associated documentation files (the "Software"),
+ * to deal in the Software without restriction, including without limitation
+ * the rights to use, copy, modify, merge, publish, distribute, sublicense,
+ * and/or sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following conditions:
+ *
+ * The above copyright notice and this permission notice (including the next
+ * paragraph) shall be included in all copies or substantial portions of the
+ * Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR
+ * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY,
+ * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL
+ * THE AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER
+ * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER
+ * DEALINGS IN THE SOFTWARE.
+ *
+ * Authors:
+ * Li Peng <peng.li@xxxxxxxxx>
+ */
+
+#include <drm/drmP.h>
+#include <drm/drm.h>
+#include "psb_intel_drv.h"
+#include "psb_intel_reg.h"
+#include "psb_drv.h"
+
+#define HDMI_READ(reg) readl(hdmi_dev->regs + (reg))
+#define HDMI_WRITE(reg, val) writel(val, hdmi_dev->regs + (reg))
+
+#define HDMI_HCR 0x1000
+#define HCR_ENABLE_HDCP (1 << 5)
+#define HCR_ENABLE_AUDIO (1 << 2)
+#define HCR_ENABLE_PIXEL (1 << 1)
+#define HCR_ENABLE_TMDS (1 << 0)
+
+#define HDMI_HICR 0x1004
+#define HDMI_HSR 0x1008
+#define HDMI_HISR 0x100C
+#define HDMI_DETECT_HDP (1 << 0)
+
+#define HDMI_VIDEO_REG 0x3000
+#define HDMI_UNIT_EN (1 << 7)
+#define HDMI_MODE_OUTPUT (1 << 0)
+#define HDMI_HBLANK_A 0x3100
+
+#define HDMI_AUDIO_CTRL 0x4000
+#define HDMI_ENABLE_AUDIO (1 << 0)
+
+#define PCH_HTOTAL_B 0x3100
+#define PCH_HBLANK_B 0x3104
+#define PCH_HSYNC_B 0x3108
+#define PCH_VTOTAL_B 0x310C
+#define PCH_VBLANK_B 0x3110
+#define PCH_VSYNC_B 0x3114
+#define PCH_PIPEBSRC 0x311C
+
+#define PCH_PIPEB_DSL 0x3800
+#define PCH_PIPEB_SLC 0x3804
+#define PCH_PIPEBCONF 0x3808
+#define PCH_PIPEBSTAT 0x3824
+
+#define CDVO_DFT 0x5000
+#define CDVO_SLEWRATE 0x5004
+#define CDVO_STRENGTH 0x5008
+#define CDVO_RCOMP 0x500C
+
+#define DPLL_CTRL 0x6000
+#define DPLL_PDIV_SHIFT 16
+#define DPLL_PDIV_MASK (0xf << 16)
+#define DPLL_PWRDN (1 << 4)
+#define DPLL_RESET (1 << 3)
+#define DPLL_FASTEN (1 << 2)
+#define DPLL_ENSTAT (1 << 1)
+#define DPLL_DITHEN (1 << 0)
+
+#define DPLL_DIV_CTRL 0x6004
+#define DPLL_CLKF_MASK 0xffffffc0
+#define DPLL_CLKR_MASK (0x3f)
+
+#define DPLL_CLK_ENABLE 0x6008
+#define DPLL_EN_DISP (1 << 31)
+#define DPLL_SEL_HDMI (1 << 8)
+#define DPLL_EN_HDMI (1 << 1)
+#define DPLL_EN_VGA (1 << 0)
+
+#define DPLL_ADJUST 0x600C
+#define DPLL_STATUS 0x6010
+#define DPLL_UPDATE 0x6014
+#define DPLL_DFT 0x6020
+
+struct intel_range {
+ int min, max;
+};
+
+struct oaktrail_hdmi_limit {
+ struct intel_range vco, np, nr, nf;
+};
+
+struct oaktrail_hdmi_clock {
+ int np;
+ int nr;
+ int nf;
+ int dot;
+};
+
+#define VCO_MIN 320000
+#define VCO_MAX 1650000
+#define NP_MIN 1
+#define NP_MAX 15
+#define NR_MIN 1
+#define NR_MAX 64
+#define NF_MIN 2
+#define NF_MAX 4095
+
+static const struct oaktrail_hdmi_limit oaktrail_hdmi_limit = {
+ .vco = { .min = VCO_MIN, .max = VCO_MAX },
+ .np = { .min = NP_MIN, .max = NP_MAX },
+ .nr = { .min = NR_MIN, .max = NR_MAX },
+ .nf = { .min = NF_MIN, .max = NF_MAX },
+};
+
+static void wait_for_vblank(struct drm_device *dev)
+{
+ /* FIXME: Can we do this as a sleep ? */
+ /* Wait for 20ms, i.e. one cycle at 50hz. */
+ mdelay(20);
+}
+
+static void scu_busy_loop(void *scu_base)
+{
+ u32 status = 0;
+ u32 loop_count = 0;
+
+ status = readl(scu_base + 0x04);
+ while (status & 1) {
+ udelay(1); /* scu processing time is in few u secods */
+ status = readl(scu_base + 0x04);
+ loop_count++;
+ /* break if scu doesn't reset busy bit after huge retry */
+ if (loop_count > 1000) {
+ DRM_DEBUG_KMS("SCU IPC timed out");
+ return;
+ }
+ }
+}
+
+static void oaktrail_hdmi_reset(struct drm_device *dev)
+{
+ void *base;
+ /* FIXME: at least make these defines */
+ unsigned int scu_ipc_mmio = 0xff11c000;
+ int scu_len = 1024;
+
+ base = ioremap((resource_size_t)scu_ipc_mmio, scu_len);
+ if (base == NULL) {
+ DRM_ERROR("failed to map SCU mmio\n");
+ return;
+ }
+
+ /* scu ipc: assert hdmi controller reset */
+ writel(0xff11d118, base + 0x0c);
+ writel(0x7fffffdf, base + 0x80);
+ writel(0x42005, base + 0x0);
+ scu_busy_loop(base);
+
+ /* scu ipc: de-assert hdmi controller reset */
+ writel(0xff11d118, base + 0x0c);
+ writel(0x7fffffff, base + 0x80);
+ writel(0x42005, base + 0x0);
+ scu_busy_loop(base);
+
+ iounmap(base);
+}
+
+static void oaktrail_hdmi_audio_enable(struct drm_device *dev)
+{
+ struct drm_psb_private *dev_priv = dev->dev_private;
+ struct oaktrail_hdmi_dev *hdmi_dev = dev_priv->hdmi_priv;
+
+ HDMI_WRITE(HDMI_HCR, 0x67);
+ HDMI_READ(HDMI_HCR);
+
+ HDMI_WRITE(0x51a8, 0x10);
+ HDMI_READ(0x51a8);
+
+ HDMI_WRITE(HDMI_AUDIO_CTRL, 0x1);
+ HDMI_READ(HDMI_AUDIO_CTRL);
+}
+
+static void oaktrail_hdmi_audio_disable(struct drm_device *dev)
+{
+ struct drm_psb_private *dev_priv = dev->dev_private;
+ struct oaktrail_hdmi_dev *hdmi_dev = dev_priv->hdmi_priv;
+
+ HDMI_WRITE(0x51a8, 0x0);
+ HDMI_READ(0x51a8);
+
+ HDMI_WRITE(HDMI_AUDIO_CTRL, 0x0);
+ HDMI_READ(HDMI_AUDIO_CTRL);
+
+ HDMI_WRITE(HDMI_HCR, 0x47);
+ HDMI_READ(HDMI_HCR);
+}
+
+void oaktrail_crtc_hdmi_dpms(struct drm_crtc *crtc, int mode)
+{
+ struct drm_device *dev = crtc->dev;
+ u32 temp;
+
+ switch (mode) {
+ case DRM_MODE_DPMS_OFF:
+ /* Disable VGACNTRL */
+ REG_WRITE(VGACNTRL, 0x80000000);
+
+ /* Disable plane */
+ temp = REG_READ(DSPBCNTR);
+ if ((temp & DISPLAY_PLANE_ENABLE) != 0) {
+ REG_WRITE(DSPBCNTR, temp & ~DISPLAY_PLANE_ENABLE);
+ REG_READ(DSPBCNTR);
+ /* Flush the plane changes */
+ REG_WRITE(DSPBSURF, REG_READ(DSPBSURF));
+ REG_READ(DSPBSURF);
+ }
+
+ /* Disable pipe B */
+ temp = REG_READ(PIPEBCONF);
+ if ((temp & PIPEACONF_ENABLE) != 0) {
+ REG_WRITE(PIPEBCONF, temp & ~PIPEACONF_ENABLE);
+ REG_READ(PIPEBCONF);
+ }
+
+ /* Disable LNW Pipes, etc */
+ temp = REG_READ(PCH_PIPEBCONF);
+ if ((temp & PIPEACONF_ENABLE) != 0) {
+ REG_WRITE(PCH_PIPEBCONF, temp & ~PIPEACONF_ENABLE);
+ REG_READ(PCH_PIPEBCONF);
+ }
+ /* wait for pipe off */
+ udelay(150);
+ /* Disable dpll */
+ temp = REG_READ(DPLL_CTRL);
+ if ((temp & DPLL_PWRDN) == 0) {
+ REG_WRITE(DPLL_CTRL, temp | (DPLL_PWRDN | DPLL_RESET));
+ REG_WRITE(DPLL_STATUS, 0x1);
+ }
+ /* wait for dpll off */
+ udelay(150);
+ break;
+ case DRM_MODE_DPMS_ON:
+ case DRM_MODE_DPMS_STANDBY:
+ case DRM_MODE_DPMS_SUSPEND:
+ /* Enable dpll */
+ temp = REG_READ(DPLL_CTRL);
+ if ((temp & DPLL_PWRDN) != 0) {
+ REG_WRITE(DPLL_CTRL, temp & ~(DPLL_PWRDN | DPLL_RESET));
+ temp = REG_READ(DPLL_CLK_ENABLE);
+ REG_WRITE(DPLL_CLK_ENABLE, temp | DPLL_EN_DISP | DPLL_SEL_HDMI | DPLL_EN_HDMI);
+ REG_READ(DPLL_CLK_ENABLE);
+ }
+ /* wait for dpll warm up */
+ udelay(150);
+
+ /* Enable pipe B */
+ temp = REG_READ(PIPEBCONF);
+ if ((temp & PIPEACONF_ENABLE) == 0) {
+ REG_WRITE(PIPEBCONF, temp | PIPEACONF_ENABLE);
+ REG_READ(PIPEBCONF);
+ }
+
+ /* Enable LNW Pipe B */
+ temp = REG_READ(PCH_PIPEBCONF);
+ if ((temp & PIPEACONF_ENABLE) == 0) {
+ REG_WRITE(PCH_PIPEBCONF, temp | PIPEACONF_ENABLE);
+ REG_READ(PCH_PIPEBCONF);
+ }
+ wait_for_vblank(dev);
+
+ /* Enable plane */
+ temp = REG_READ(DSPBCNTR);
+ if ((temp & DISPLAY_PLANE_ENABLE) == 0) {
+ REG_WRITE(DSPBCNTR, temp | DISPLAY_PLANE_ENABLE);
+ /* Flush the plane changes */
+ REG_WRITE(DSPBSURF, REG_READ(DSPBSURF));
+ REG_READ(DSPBSURF);
+ }
+ psb_intel_crtc_load_lut(crtc);
+ }
+ /* DSPARB */
+ REG_WRITE(DSPARB, 0x00003fbf);
+ /* FW1 */
+ REG_WRITE(0x70034, 0x3f880a0a);
+ /* FW2 */
+ REG_WRITE(0x70038, 0x0b060808);
+ /* FW4 */
+ REG_WRITE(0x70050, 0x08030404);
+ /* FW5 */
+ REG_WRITE(0x70054, 0x04040404);
+ /* LNC Chicken Bits */
+ REG_WRITE(0x70400, 0x4000);
+}
+
+
+static void oaktrail_hdmi_dpms(struct drm_encoder *encoder, int mode)
+{
+ static int dpms_mode = -1;
+
+ struct drm_device *dev = encoder->dev;
+ struct drm_psb_private *dev_priv = dev->dev_private;
+ struct oaktrail_hdmi_dev *hdmi_dev = dev_priv->hdmi_priv;
+ u32 temp;
+
+ if (dpms_mode == mode)
+ return;
+
+ if (mode != DRM_MODE_DPMS_ON)
+ temp = 0x0;
+ else
+ temp = 0x99;
+
+ dpms_mode = mode;
+ HDMI_WRITE(HDMI_VIDEO_REG, temp);
+}
+
+static unsigned int htotal_calculate(struct drm_display_mode *mode)
+{
+ u32 htotal, new_crtc_htotal;
+
+ htotal = (mode->crtc_hdisplay - 1) | ((mode->crtc_htotal - 1) << 16);
+
+ /*
+ * 1024 x 768 new_crtc_htotal = 0x1024;
+ * 1280 x 1024 new_crtc_htotal = 0x0c34;
+ */
+ new_crtc_htotal = (mode->crtc_htotal - 1) * 200 * 1000 / mode->clock;
+
+ return (mode->crtc_hdisplay - 1) | (new_crtc_htotal << 16);
+}
+
+static void oaktrail_hdmi_find_dpll(struct drm_crtc *crtc, int target,
+ int refclk, struct oaktrail_hdmi_clock *best_clock)
+{
+ int np_min, np_max, nr_min, nr_max;
+ int np, nr, nf;
+
+ np_min = DIV_ROUND_UP(oaktrail_hdmi_limit.vco.min, target * 10);
+ np_max = oaktrail_hdmi_limit.vco.max / (target * 10);
+ if (np_min < oaktrail_hdmi_limit.np.min)
+ np_min = oaktrail_hdmi_limit.np.min;
+ if (np_max > oaktrail_hdmi_limit.np.max)
+ np_max = oaktrail_hdmi_limit.np.max;
+
+ nr_min = DIV_ROUND_UP((refclk * 1000), (target * 10 * np_max));
+ nr_max = DIV_ROUND_UP((refclk * 1000), (target * 10 * np_min));
+ if (nr_min < oaktrail_hdmi_limit.nr.min)
+ nr_min = oaktrail_hdmi_limit.nr.min;
+ if (nr_max > oaktrail_hdmi_limit.nr.max)
+ nr_max = oaktrail_hdmi_limit.nr.max;
+
+ np = DIV_ROUND_UP((refclk * 1000), (target * 10 * nr_max));
+ nr = DIV_ROUND_UP((refclk * 1000), (target * 10 * np));
+ nf = DIV_ROUND_CLOSEST((target * 10 * np * nr), refclk);
+ DRM_DEBUG_KMS("np, nr, nf %d %d %d\n", np, nr, nf);
+
+ /*
+ * 1024 x 768 np = 1; nr = 0x26; nf = 0x0fd8000;
+ * 1280 x 1024 np = 1; nr = 0x17; nf = 0x1034000;
+ */
+ best_clock->np = np;
+ best_clock->nr = nr - 1;
+ best_clock->nf = (nf << 14);
+}
+
+int oaktrail_crtc_hdmi_mode_set(struct drm_crtc *crtc,
+ struct drm_display_mode *mode,
+ struct drm_display_mode *adjusted_mode,
+ int x, int y,
+ struct drm_framebuffer *old_fb)
+{
+ struct drm_device *dev = crtc->dev;
+ struct drm_psb_private *dev_priv = dev->dev_private;
+ struct oaktrail_hdmi_dev *hdmi_dev = dev_priv->hdmi_priv;
+ int pipe = 1;
+ int htot_reg = (pipe == 0) ? HTOTAL_A : HTOTAL_B;
+ int hblank_reg = (pipe == 0) ? HBLANK_A : HBLANK_B;
+ int hsync_reg = (pipe == 0) ? HSYNC_A : HSYNC_B;
+ int vtot_reg = (pipe == 0) ? VTOTAL_A : VTOTAL_B;
+ int vblank_reg = (pipe == 0) ? VBLANK_A : VBLANK_B;
+ int vsync_reg = (pipe == 0) ? VSYNC_A : VSYNC_B;
+ int dspsize_reg = (pipe == 0) ? DSPASIZE : DSPBSIZE;
+ int dsppos_reg = (pipe == 0) ? DSPAPOS : DSPBPOS;
+ int pipesrc_reg = (pipe == 0) ? PIPEASRC : PIPEBSRC;
+ int pipeconf_reg = (pipe == 0) ? PIPEACONF : PIPEBCONF;
+ int refclk;
+ struct oaktrail_hdmi_clock clock;
+ u32 dspcntr, pipeconf, dpll, temp;
+ int dspcntr_reg = DSPBCNTR;
+
+ /* Disable the VGA plane that we never use */
+ REG_WRITE(VGACNTRL, VGA_DISP_DISABLE);
+
+ /* XXX: Disable the panel fitter if it was on our pipe */
+
+ /* Disable dpll if necessary */
+ dpll = REG_READ(DPLL_CTRL);
+ if ((dpll & DPLL_PWRDN) == 0) {
+ REG_WRITE(DPLL_CTRL, dpll | (DPLL_PWRDN | DPLL_RESET));
+ REG_WRITE(DPLL_DIV_CTRL, 0x00000000);
+ REG_WRITE(DPLL_STATUS, 0x1);
+ }
+ udelay(150);
+
+ /* reset controller: FIXME - can we sort out the ioremap mess ? */
+ iounmap(hdmi_dev->regs);
+ oaktrail_hdmi_reset(dev);
+
+ /* program and enable dpll */
+ refclk = 25000;
+ oaktrail_hdmi_find_dpll(crtc, adjusted_mode->clock, refclk, &clock);
+
+ /* Setting DPLL */
+ dpll = REG_READ(DPLL_CTRL);
+ dpll &= ~DPLL_PDIV_MASK;
+ dpll &= ~(DPLL_PWRDN | DPLL_RESET);
+ REG_WRITE(DPLL_CTRL, 0x00000008);
+ REG_WRITE(DPLL_DIV_CTRL, ((clock.nf << 6) | clock.nr));
+ REG_WRITE(DPLL_ADJUST, ((clock.nf >> 14) - 1));
+ REG_WRITE(DPLL_CTRL, (dpll | (clock.np << DPLL_PDIV_SHIFT) | DPLL_ENSTAT | DPLL_DITHEN));
+ REG_WRITE(DPLL_UPDATE, 0x80000000);
+ REG_WRITE(DPLL_CLK_ENABLE, 0x80050102);
+ udelay(150);
+
+ hdmi_dev->regs = ioremap(hdmi_dev->mmio, hdmi_dev->mmio_len);
+ if (hdmi_dev->regs == NULL) {
+ DRM_ERROR("failed to do hdmi mmio mapping\n");
+ return -ENOMEM;
+ }
+
+ /* configure HDMI */
+ HDMI_WRITE(0x1004, 0x1fd);
+ HDMI_WRITE(0x2000, 0x1);
+ HDMI_WRITE(0x2008, 0x0);
+ HDMI_WRITE(0x3130, 0x8);
+ HDMI_WRITE(0x101c, 0x1800810);
+
+ temp = htotal_calculate(adjusted_mode);
+ REG_WRITE(htot_reg, temp);
+ REG_WRITE(hblank_reg, (adjusted_mode->crtc_hblank_start - 1) | ((adjusted_mode->crtc_hblank_end - 1) << 16));
+ REG_WRITE(hsync_reg, (adjusted_mode->crtc_hsync_start - 1) | ((adjusted_mode->crtc_hsync_end - 1) << 16));
+ REG_WRITE(vtot_reg, (adjusted_mode->crtc_vdisplay - 1) | ((adjusted_mode->crtc_vtotal - 1) << 16));
+ REG_WRITE(vblank_reg, (adjusted_mode->crtc_vblank_start - 1) | ((adjusted_mode->crtc_vblank_end - 1) << 16));
+ REG_WRITE(vsync_reg, (adjusted_mode->crtc_vsync_start - 1) | ((adjusted_mode->crtc_vsync_end - 1) << 16));
+ REG_WRITE(pipesrc_reg,
+ ((mode->crtc_hdisplay - 1) << 16) | (mode->crtc_vdisplay - 1));
+
+ REG_WRITE(PCH_HTOTAL_B, (adjusted_mode->crtc_hdisplay - 1) | ((adjusted_mode->crtc_htotal - 1) << 16));
+ REG_WRITE(PCH_HBLANK_B, (adjusted_mode->crtc_hblank_start - 1) | ((adjusted_mode->crtc_hblank_end - 1) << 16));
+ REG_WRITE(PCH_HSYNC_B, (adjusted_mode->crtc_hsync_start - 1) | ((adjusted_mode->crtc_hsync_end - 1) << 16));
+ REG_WRITE(PCH_VTOTAL_B, (adjusted_mode->crtc_vdisplay - 1) | ((adjusted_mode->crtc_vtotal - 1) << 16));
+ REG_WRITE(PCH_VBLANK_B, (adjusted_mode->crtc_vblank_start - 1) | ((adjusted_mode->crtc_vblank_end - 1) << 16));
+ REG_WRITE(PCH_VSYNC_B, (adjusted_mode->crtc_vsync_start - 1) | ((adjusted_mode->crtc_vsync_end - 1) << 16));
+ REG_WRITE(PCH_PIPEBSRC,
+ ((mode->crtc_hdisplay - 1) << 16) | (mode->crtc_vdisplay - 1));
+
+ temp = adjusted_mode->crtc_hblank_end - adjusted_mode->crtc_hblank_start;
+ HDMI_WRITE(HDMI_HBLANK_A, ((adjusted_mode->crtc_hdisplay - 1) << 16) | temp);
+
+ REG_WRITE(dspsize_reg,
+ ((mode->vdisplay - 1) << 16) | (mode->hdisplay - 1));
+ REG_WRITE(dsppos_reg, 0);
+
+ /* Flush the plane changes */
+ {
+ struct drm_crtc_helper_funcs *crtc_funcs = crtc->helper_private;
+ crtc_funcs->mode_set_base(crtc, x, y, old_fb);
+ }
+
+ /* Set up the display plane register */
+ dspcntr = REG_READ(dspcntr_reg);
+ dspcntr |= DISPPLANE_GAMMA_ENABLE;
+ dspcntr |= DISPPLANE_SEL_PIPE_B;
+ dspcntr |= DISPLAY_PLANE_ENABLE;
+
+ /* setup pipeconf */
+ pipeconf = REG_READ(pipeconf_reg);
+ pipeconf |= PIPEACONF_ENABLE;
+
+ REG_WRITE(pipeconf_reg, pipeconf);
+ REG_READ(pipeconf_reg);
+
+ REG_WRITE(PCH_PIPEBCONF, pipeconf);
+ REG_READ(PCH_PIPEBCONF);
+ wait_for_vblank(dev);
+
+ REG_WRITE(dspcntr_reg, dspcntr);
+ wait_for_vblank(dev);
+
+ return 0;
+}
+
+static int oaktrail_hdmi_mode_valid(struct drm_connector *connector,
+ struct drm_display_mode *mode)
+{
+ if (mode->clock > 165000)
+ return MODE_CLOCK_HIGH;
+ if (mode->clock < 20000)
+ return MODE_CLOCK_LOW;
+
+ if (mode->flags & DRM_MODE_FLAG_DBLSCAN)
+ return MODE_NO_DBLESCAN;
+
+ return MODE_OK;
+}
+
+static bool oaktrail_hdmi_mode_fixup(struct drm_encoder *encoder,
+ struct drm_display_mode *mode,
+ struct drm_display_mode *adjusted_mode)
+{
+ return true;
+}
+
+static enum drm_connector_status
+oaktrail_hdmi_detect(struct drm_connector *connector, bool force)
+{
+ enum drm_connector_status status;
+ struct drm_device *dev = connector->dev;
+ struct drm_psb_private *dev_priv = dev->dev_private;
+ struct oaktrail_hdmi_dev *hdmi_dev = dev_priv->hdmi_priv;
+ u32 temp;
+
+ temp = HDMI_READ(HDMI_HSR);
+ DRM_DEBUG_KMS("HDMI_HSR %x\n", temp);
+
+ if ((temp & HDMI_DETECT_HDP) != 0)
+ status = connector_status_connected;
+ else
+ status = connector_status_disconnected;
+
+ return status;
+}
+
+static const unsigned char raw_edid[] = {
+ 0x00, 0xff, 0xff, 0xff, 0xff, 0xff, 0xff, 0x00, 0x10, 0xac, 0x2f, 0xa0,
+ 0x53, 0x55, 0x33, 0x30, 0x16, 0x13, 0x01, 0x03, 0x0e, 0x3a, 0x24, 0x78,
+ 0xea, 0xe9, 0xf5, 0xac, 0x51, 0x30, 0xb4, 0x25, 0x11, 0x50, 0x54, 0xa5,
+ 0x4b, 0x00, 0x81, 0x80, 0xa9, 0x40, 0x71, 0x4f, 0xb3, 0x00, 0x01, 0x01,
+ 0x01, 0x01, 0x01, 0x01, 0x01, 0x01, 0x28, 0x3c, 0x80, 0xa0, 0x70, 0xb0,
+ 0x23, 0x40, 0x30, 0x20, 0x36, 0x00, 0x46, 0x6c, 0x21, 0x00, 0x00, 0x1a,
+ 0x00, 0x00, 0x00, 0xff, 0x00, 0x47, 0x4e, 0x37, 0x32, 0x31, 0x39, 0x35,
+ 0x52, 0x30, 0x33, 0x55, 0x53, 0x0a, 0x00, 0x00, 0x00, 0xfc, 0x00, 0x44,
+ 0x45, 0x4c, 0x4c, 0x20, 0x32, 0x37, 0x30, 0x39, 0x57, 0x0a, 0x20, 0x20,
+ 0x00, 0x00, 0x00, 0xfd, 0x00, 0x38, 0x4c, 0x1e, 0x53, 0x11, 0x00, 0x0a,
+ 0x20, 0x20, 0x20, 0x20, 0x20, 0x20, 0x00, 0x8d
+};
+
+static int oaktrail_hdmi_get_modes(struct drm_connector *connector)
+{
+ struct drm_device *dev = connector->dev;
+ struct drm_psb_private *dev_priv = dev->dev_private;
+ struct i2c_adapter *i2c_adap;
+ struct edid *edid;
+ struct drm_display_mode *mode, *t;
+ int i = 0, ret = 0;
+
+ i2c_adap = i2c_get_adapter(3);
+ if (i2c_adap == NULL) {
+ DRM_ERROR("No ddc adapter available!\n");
+ edid = (struct edid *)raw_edid;
+ } else {
+ edid = (struct edid *)raw_edid;
+ /* FIXME ? edid = drm_get_edid(connector, i2c_adap); */
+ }
+
+ if (edid) {
+ drm_mode_connector_update_edid_property(connector, edid);
+ ret = drm_add_edid_modes(connector, edid);
+ connector->display_info.raw_edid = NULL;
+ }
+
+ /*
+ * prune modes that require frame buffer bigger than stolen mem
+ */
+ list_for_each_entry_safe(mode, t, &connector->probed_modes, head) {
+ if ((mode->hdisplay * mode->vdisplay * 4) >= dev_priv->vram_stolen_size) {
+ i++;
+ drm_mode_remove(connector, mode);
+ }
+ }
+ return ret - i;
+}
+
+static void oaktrail_hdmi_mode_set(struct drm_encoder *encoder,
+ struct drm_display_mode *mode,
+ struct drm_display_mode *adjusted_mode)
+{
+ struct drm_device *dev = encoder->dev;
+
+ oaktrail_hdmi_audio_enable(dev);
+ return;
+}
+
+static void oaktrail_hdmi_destroy(struct drm_connector *connector)
+{
+ return;
+}
+
+static const struct drm_encoder_helper_funcs oaktrail_hdmi_helper_funcs = {
+ .dpms = oaktrail_hdmi_dpms,
+ .mode_fixup = oaktrail_hdmi_mode_fixup,
+ .prepare = psb_intel_encoder_prepare,
+ .mode_set = oaktrail_hdmi_mode_set,
+ .commit = psb_intel_encoder_commit,
+};
+
+static const struct drm_connector_helper_funcs
+ oaktrail_hdmi_connector_helper_funcs = {
+ .get_modes = oaktrail_hdmi_get_modes,
+ .mode_valid = oaktrail_hdmi_mode_valid,
+ .best_encoder = psb_intel_best_encoder,
+};
+
+static const struct drm_connector_funcs oaktrail_hdmi_connector_funcs = {
+ .dpms = drm_helper_connector_dpms,
+ .detect = oaktrail_hdmi_detect,
+ .fill_modes = drm_helper_probe_single_connector_modes,
+ .destroy = oaktrail_hdmi_destroy,
+};
+
+static void oaktrail_hdmi_enc_destroy(struct drm_encoder *encoder)
+{
+ drm_encoder_cleanup(encoder);
+}
+
+static const struct drm_encoder_funcs oaktrail_hdmi_enc_funcs = {
+ .destroy = oaktrail_hdmi_enc_destroy,
+};
+
+void oaktrail_hdmi_init(struct drm_device *dev,
+ struct psb_intel_mode_device *mode_dev)
+{
+ struct psb_intel_output *psb_intel_output;
+ struct drm_connector *connector;
+ struct drm_encoder *encoder;
+
+ psb_intel_output = kzalloc(sizeof(struct psb_intel_output), GFP_KERNEL);
+ if (!psb_intel_output)
+ return;
+
+ psb_intel_output->mode_dev = mode_dev;
+ connector = &psb_intel_output->base;
+ encoder = &psb_intel_output->enc;
+ drm_connector_init(dev, &psb_intel_output->base,
+ &oaktrail_hdmi_connector_funcs,
+ DRM_MODE_CONNECTOR_DVID);
+
+ drm_encoder_init(dev, &psb_intel_output->enc,
+ &oaktrail_hdmi_enc_funcs,
+ DRM_MODE_ENCODER_TMDS);
+
+ drm_mode_connector_attach_encoder(&psb_intel_output->base,
+ &psb_intel_output->enc);
+
+ psb_intel_output->type = INTEL_OUTPUT_HDMI;
+ drm_encoder_helper_add(encoder, &oaktrail_hdmi_helper_funcs);
+ drm_connector_helper_add(connector, &oaktrail_hdmi_connector_helper_funcs);
+
+ connector->display_info.subpixel_order = SubPixelHorizontalRGB;
+ connector->interlace_allowed = false;
+ connector->doublescan_allowed = false;
+ drm_sysfs_connector_add(connector);
+
+ return;
+}
+
+static DEFINE_PCI_DEVICE_TABLE(hdmi_ids) = {
+ { PCI_DEVICE(PCI_VENDOR_ID_INTEL, 0x080d) },
+ {}
+};
+
+void oaktrail_hdmi_setup(struct drm_device *dev)
+{
+ struct drm_psb_private *dev_priv = dev->dev_private;
+ struct pci_dev *pdev;
+ struct oaktrail_hdmi_dev *hdmi_dev;
+ int ret;
+
+ pdev = pci_get_device(PCI_VENDOR_ID_INTEL, 0x080d, NULL);
+ if (!pdev)
+ return;
+
+ hdmi_dev = kzalloc(sizeof(struct oaktrail_hdmi_dev), GFP_KERNEL);
+ if (!hdmi_dev) {
+ dev_err(dev->dev, "failed to allocate memory\n");
+ goto out;
+ }
+
+
+ ret = pci_enable_device(pdev);
+ if (ret) {
+ dev_err(dev->dev, "failed to enable hdmi controller\n");
+ goto free;
+ }
+
+ hdmi_dev->mmio = pci_resource_start(pdev, 0);
+ hdmi_dev->mmio_len = pci_resource_len(pdev, 0);
+ hdmi_dev->regs = ioremap(hdmi_dev->mmio, hdmi_dev->mmio_len);
+ if (!hdmi_dev->regs) {
+ dev_err(dev->dev, "failed to map hdmi mmio\n");
+ goto free;
+ }
+
+ hdmi_dev->dev = pdev;
+ pci_set_drvdata(pdev, hdmi_dev);
+
+ /* Initialize i2c controller */
+ ret = oaktrail_hdmi_i2c_init(hdmi_dev->dev);
+ if (ret)
+ dev_err(dev->dev, "HDMI I2C initialization failed\n");
+
+ dev_priv->hdmi_priv = hdmi_dev;
+ oaktrail_hdmi_audio_disable(dev);
+ return;
+
+free:
+ kfree(hdmi_dev);
+out:
+ return;
+}
+
+void oaktrail_hdmi_teardown(struct drm_device *dev)
+{
+ struct drm_psb_private *dev_priv = dev->dev_private;
+ struct oaktrail_hdmi_dev *hdmi_dev = dev_priv->hdmi_priv;
+ struct pci_dev *pdev;
+
+ if (hdmi_dev) {
+ pdev = hdmi_dev->dev;
+ pci_set_drvdata(pdev, NULL);
+ oaktrail_hdmi_i2c_exit(pdev);
+ iounmap(hdmi_dev->regs);
+ kfree(hdmi_dev);
+ pci_dev_put(pdev);
+ }
+}
+
+/* save HDMI register state */
+void oaktrail_hdmi_save(struct drm_device *dev)
+{
+ struct drm_psb_private *dev_priv = dev->dev_private;
+ struct oaktrail_hdmi_dev *hdmi_dev = dev_priv->hdmi_priv;
+ int i;
+
+ /* dpll */
+ hdmi_dev->saveDPLL_CTRL = PSB_RVDC32(DPLL_CTRL);
+ hdmi_dev->saveDPLL_DIV_CTRL = PSB_RVDC32(DPLL_DIV_CTRL);
+ hdmi_dev->saveDPLL_ADJUST = PSB_RVDC32(DPLL_ADJUST);
+ hdmi_dev->saveDPLL_UPDATE = PSB_RVDC32(DPLL_UPDATE);
+ hdmi_dev->saveDPLL_CLK_ENABLE = PSB_RVDC32(DPLL_CLK_ENABLE);
+
+ /* pipe B */
+ dev_priv->savePIPEBCONF = PSB_RVDC32(PIPEBCONF);
+ dev_priv->savePIPEBSRC = PSB_RVDC32(PIPEBSRC);
+ dev_priv->saveHTOTAL_B = PSB_RVDC32(HTOTAL_B);
+ dev_priv->saveHBLANK_B = PSB_RVDC32(HBLANK_B);
+ dev_priv->saveHSYNC_B = PSB_RVDC32(HSYNC_B);
+ dev_priv->saveVTOTAL_B = PSB_RVDC32(VTOTAL_B);
+ dev_priv->saveVBLANK_B = PSB_RVDC32(VBLANK_B);
+ dev_priv->saveVSYNC_B = PSB_RVDC32(VSYNC_B);
+
+ hdmi_dev->savePCH_PIPEBCONF = PSB_RVDC32(PCH_PIPEBCONF);
+ hdmi_dev->savePCH_PIPEBSRC = PSB_RVDC32(PCH_PIPEBSRC);
+ hdmi_dev->savePCH_HTOTAL_B = PSB_RVDC32(PCH_HTOTAL_B);
+ hdmi_dev->savePCH_HBLANK_B = PSB_RVDC32(PCH_HBLANK_B);
+ hdmi_dev->savePCH_HSYNC_B = PSB_RVDC32(PCH_HSYNC_B);
+ hdmi_dev->savePCH_VTOTAL_B = PSB_RVDC32(PCH_VTOTAL_B);
+ hdmi_dev->savePCH_VBLANK_B = PSB_RVDC32(PCH_VBLANK_B);
+ hdmi_dev->savePCH_VSYNC_B = PSB_RVDC32(PCH_VSYNC_B);
+
+ /* plane */
+ dev_priv->saveDSPBCNTR = PSB_RVDC32(DSPBCNTR);
+ dev_priv->saveDSPBSTRIDE = PSB_RVDC32(DSPBSTRIDE);
+ dev_priv->saveDSPBADDR = PSB_RVDC32(DSPBBASE);
+ dev_priv->saveDSPBSURF = PSB_RVDC32(DSPBSURF);
+ dev_priv->saveDSPBLINOFF = PSB_RVDC32(DSPBLINOFF);
+ dev_priv->saveDSPBTILEOFF = PSB_RVDC32(DSPBTILEOFF);
+
+ /* cursor B */
+ dev_priv->saveDSPBCURSOR_CTRL = PSB_RVDC32(CURBCNTR);
+ dev_priv->saveDSPBCURSOR_BASE = PSB_RVDC32(CURBBASE);
+ dev_priv->saveDSPBCURSOR_POS = PSB_RVDC32(CURBPOS);
+
+ /* save palette */
+ for (i = 0; i < 256; i++)
+ dev_priv->save_palette_b[i] = PSB_RVDC32(PALETTE_B + (i << 2));
+}
+
+/* restore HDMI register state */
+void oaktrail_hdmi_restore(struct drm_device *dev)
+{
+ struct drm_psb_private *dev_priv = dev->dev_private;
+ struct oaktrail_hdmi_dev *hdmi_dev = dev_priv->hdmi_priv;
+ int i;
+
+ /* dpll */
+ PSB_WVDC32(hdmi_dev->saveDPLL_CTRL, DPLL_CTRL);
+ PSB_WVDC32(hdmi_dev->saveDPLL_DIV_CTRL, DPLL_DIV_CTRL);
+ PSB_WVDC32(hdmi_dev->saveDPLL_ADJUST, DPLL_ADJUST);
+ PSB_WVDC32(hdmi_dev->saveDPLL_UPDATE, DPLL_UPDATE);
+ PSB_WVDC32(hdmi_dev->saveDPLL_CLK_ENABLE, DPLL_CLK_ENABLE);
+ DRM_UDELAY(150);
+
+ /* pipe */
+ PSB_WVDC32(dev_priv->savePIPEBSRC, PIPEBSRC);
+ PSB_WVDC32(dev_priv->saveHTOTAL_B, HTOTAL_B);
+ PSB_WVDC32(dev_priv->saveHBLANK_B, HBLANK_B);
+ PSB_WVDC32(dev_priv->saveHSYNC_B, HSYNC_B);
+ PSB_WVDC32(dev_priv->saveVTOTAL_B, VTOTAL_B);
+ PSB_WVDC32(dev_priv->saveVBLANK_B, VBLANK_B);
+ PSB_WVDC32(dev_priv->saveVSYNC_B, VSYNC_B);
+
+ PSB_WVDC32(hdmi_dev->savePCH_PIPEBSRC, PCH_PIPEBSRC);
+ PSB_WVDC32(hdmi_dev->savePCH_HTOTAL_B, PCH_HTOTAL_B);
+ PSB_WVDC32(hdmi_dev->savePCH_HBLANK_B, PCH_HBLANK_B);
+ PSB_WVDC32(hdmi_dev->savePCH_HSYNC_B, PCH_HSYNC_B);
+ PSB_WVDC32(hdmi_dev->savePCH_VTOTAL_B, PCH_VTOTAL_B);
+ PSB_WVDC32(hdmi_dev->savePCH_VBLANK_B, PCH_VBLANK_B);
+ PSB_WVDC32(hdmi_dev->savePCH_VSYNC_B, PCH_VSYNC_B);
+
+ PSB_WVDC32(dev_priv->savePIPEBCONF, PIPEBCONF);
+ PSB_WVDC32(hdmi_dev->savePCH_PIPEBCONF, PCH_PIPEBCONF);
+
+ /* plane */
+ PSB_WVDC32(dev_priv->saveDSPBLINOFF, DSPBLINOFF);
+ PSB_WVDC32(dev_priv->saveDSPBSTRIDE, DSPBSTRIDE);
+ PSB_WVDC32(dev_priv->saveDSPBTILEOFF, DSPBTILEOFF);
+ PSB_WVDC32(dev_priv->saveDSPBCNTR, DSPBCNTR);
+ PSB_WVDC32(dev_priv->saveDSPBSURF, DSPBSURF);
+
+ /* cursor B */
+ PSB_WVDC32(dev_priv->saveDSPBCURSOR_CTRL, CURBCNTR);
+ PSB_WVDC32(dev_priv->saveDSPBCURSOR_POS, CURBPOS);
+ PSB_WVDC32(dev_priv->saveDSPBCURSOR_BASE, CURBBASE);
+
+ /* restore palette */
+ for (i = 0; i < 256; i++)
+ PSB_WVDC32(dev_priv->save_palette_b[i], PALETTE_B + (i << 2));
+}
diff --git a/drivers/gpu/drm/gma500/oaktrail_hdmi_i2c.c b/drivers/gpu/drm/gma500/oaktrail_hdmi_i2c.c
new file mode 100644
index 0000000..d454e6f
--- /dev/null
+++ b/drivers/gpu/drm/gma500/oaktrail_hdmi_i2c.c
@@ -0,0 +1,327 @@
+/*
+ * Copyright © 2010 Intel Corporation
+ *
+ * Permission is hereby granted, free of charge, to any person obtaining a
+ * copy of this software and associated documentation files (the "Software"),
+ * to deal in the Software without restriction, including without limitation
+ * the rights to use, copy, modify, merge, publish, distribute, sublicense,
+ * and/or sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following conditions:
+ *
+ * The above copyright notice and this permission notice (including the next
+ * paragraph) shall be included in all copies or substantial portions of the
+ * Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR
+ * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY,
+ * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL
+ * THE AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER
+ * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER
+ * DEALINGS IN THE SOFTWARE.
+ *
+ * Authors:
+ * Li Peng <peng.li@xxxxxxxxx>
+ */
+
+#include <linux/mutex.h>
+#include <linux/pci.h>
+#include <linux/i2c.h>
+#include <linux/interrupt.h>
+#include <linux/delay.h>
+#include "psb_drv.h"
+
+#define HDMI_READ(reg) readl(hdmi_dev->regs + (reg))
+#define HDMI_WRITE(reg, val) writel(val, hdmi_dev->regs + (reg))
+
+#define HDMI_HCR 0x1000
+#define HCR_DETECT_HDP (1 << 6)
+#define HCR_ENABLE_HDCP (1 << 5)
+#define HCR_ENABLE_AUDIO (1 << 2)
+#define HCR_ENABLE_PIXEL (1 << 1)
+#define HCR_ENABLE_TMDS (1 << 0)
+#define HDMI_HICR 0x1004
+#define HDMI_INTR_I2C_ERROR (1 << 4)
+#define HDMI_INTR_I2C_FULL (1 << 3)
+#define HDMI_INTR_I2C_DONE (1 << 2)
+#define HDMI_INTR_HPD (1 << 0)
+#define HDMI_HSR 0x1008
+#define HDMI_HISR 0x100C
+#define HDMI_HI2CRDB0 0x1200
+#define HDMI_HI2CHCR 0x1240
+#define HI2C_HDCP_WRITE (0 << 2)
+#define HI2C_HDCP_RI_READ (1 << 2)
+#define HI2C_HDCP_READ (2 << 2)
+#define HI2C_EDID_READ (3 << 2)
+#define HI2C_READ_CONTINUE (1 << 1)
+#define HI2C_ENABLE_TRANSACTION (1 << 0)
+
+#define HDMI_ICRH 0x1100
+#define HDMI_HI2CTDR0 0x1244
+#define HDMI_HI2CTDR1 0x1248
+
+#define I2C_STAT_INIT 0
+#define I2C_READ_DONE 1
+#define I2C_TRANSACTION_DONE 2
+
+struct hdmi_i2c_dev {
+ struct i2c_adapter *adap;
+ struct mutex i2c_lock;
+ struct completion complete;
+ int status;
+ struct i2c_msg *msg;
+ int buf_offset;
+};
+
+static void hdmi_i2c_irq_enable(struct oaktrail_hdmi_dev *hdmi_dev)
+{
+ u32 temp;
+
+ temp = HDMI_READ(HDMI_HICR);
+ temp |= (HDMI_INTR_I2C_ERROR | HDMI_INTR_I2C_FULL | HDMI_INTR_I2C_DONE);
+ HDMI_WRITE(HDMI_HICR, temp);
+ HDMI_READ(HDMI_HICR);
+}
+
+static void hdmi_i2c_irq_disable(struct oaktrail_hdmi_dev *hdmi_dev)
+{
+ HDMI_WRITE(HDMI_HICR, 0x0);
+ HDMI_READ(HDMI_HICR);
+}
+
+static int xfer_read(struct i2c_adapter *adap, struct i2c_msg *pmsg)
+{
+ struct oaktrail_hdmi_dev *hdmi_dev = i2c_get_adapdata(adap);
+ struct hdmi_i2c_dev *i2c_dev = hdmi_dev->i2c_dev;
+ u32 temp;
+
+ i2c_dev->status = I2C_STAT_INIT;
+ i2c_dev->msg = pmsg;
+ i2c_dev->buf_offset = 0;
+ INIT_COMPLETION(i2c_dev->complete);
+
+ /* Enable I2C transaction */
+ temp = ((pmsg->len) << 20) | HI2C_EDID_READ | HI2C_ENABLE_TRANSACTION;
+ HDMI_WRITE(HDMI_HI2CHCR, temp);
+ HDMI_READ(HDMI_HI2CHCR);
+
+ while (i2c_dev->status != I2C_TRANSACTION_DONE)
+ wait_for_completion_interruptible_timeout(&i2c_dev->complete,
+ 10 * HZ);
+
+ return 0;
+}
+
+static int xfer_write(struct i2c_adapter *adap, struct i2c_msg *pmsg)
+{
+ /*
+ * XXX: i2c write seems isn't useful for EDID probe, don't do anything
+ */
+ return 0;
+}
+
+static int oaktrail_hdmi_i2c_access(struct i2c_adapter *adap,
+ struct i2c_msg *pmsg,
+ int num)
+{
+ struct oaktrail_hdmi_dev *hdmi_dev = i2c_get_adapdata(adap);
+ struct hdmi_i2c_dev *i2c_dev = hdmi_dev->i2c_dev;
+ int i, err = 0;
+
+ mutex_lock(&i2c_dev->i2c_lock);
+
+ /* Enable i2c unit */
+ HDMI_WRITE(HDMI_ICRH, 0x00008760);
+
+ /* Enable irq */
+ hdmi_i2c_irq_enable(hdmi_dev);
+ for (i = 0; i < num; i++) {
+ if (pmsg->len && pmsg->buf) {
+ if (pmsg->flags & I2C_M_RD)
+ err = xfer_read(adap, pmsg);
+ else
+ err = xfer_write(adap, pmsg);
+ }
+ pmsg++; /* next message */
+ }
+
+ /* Disable irq */
+ hdmi_i2c_irq_disable(hdmi_dev);
+
+ mutex_unlock(&i2c_dev->i2c_lock);
+
+ return i;
+}
+
+static u32 oaktrail_hdmi_i2c_func(struct i2c_adapter *adapter)
+{
+ return I2C_FUNC_I2C | I2C_FUNC_10BIT_ADDR;
+}
+
+static const struct i2c_algorithm oaktrail_hdmi_i2c_algorithm = {
+ .master_xfer = oaktrail_hdmi_i2c_access,
+ .functionality = oaktrail_hdmi_i2c_func,
+};
+
+static struct i2c_adapter oaktrail_hdmi_i2c_adapter = {
+ .name = "oaktrail_hdmi_i2c",
+ .nr = 3,
+ .owner = THIS_MODULE,
+ .class = I2C_CLASS_DDC,
+ .algo = &oaktrail_hdmi_i2c_algorithm,
+};
+
+static void hdmi_i2c_read(struct oaktrail_hdmi_dev *hdmi_dev)
+{
+ struct hdmi_i2c_dev *i2c_dev = hdmi_dev->i2c_dev;
+ struct i2c_msg *msg = i2c_dev->msg;
+ u8 *buf = msg->buf;
+ u32 temp;
+ int i, offset;
+
+ offset = i2c_dev->buf_offset;
+ for (i = 0; i < 0x10; i++) {
+ temp = HDMI_READ(HDMI_HI2CRDB0 + (i * 4));
+ memcpy(buf + (offset + i * 4), &temp, 4);
+ }
+ i2c_dev->buf_offset += (0x10 * 4);
+
+ /* clearing read buffer full intr */
+ temp = HDMI_READ(HDMI_HISR);
+ HDMI_WRITE(HDMI_HISR, temp | HDMI_INTR_I2C_FULL);
+ HDMI_READ(HDMI_HISR);
+
+ /* continue read transaction */
+ temp = HDMI_READ(HDMI_HI2CHCR);
+ HDMI_WRITE(HDMI_HI2CHCR, temp | HI2C_READ_CONTINUE);
+ HDMI_READ(HDMI_HI2CHCR);
+
+ i2c_dev->status = I2C_READ_DONE;
+ return;
+}
+
+static void hdmi_i2c_transaction_done(struct oaktrail_hdmi_dev *hdmi_dev)
+{
+ struct hdmi_i2c_dev *i2c_dev = hdmi_dev->i2c_dev;
+ u32 temp;
+
+ /* clear transaction done intr */
+ temp = HDMI_READ(HDMI_HISR);
+ HDMI_WRITE(HDMI_HISR, temp | HDMI_INTR_I2C_DONE);
+ HDMI_READ(HDMI_HISR);
+
+
+ temp = HDMI_READ(HDMI_HI2CHCR);
+ HDMI_WRITE(HDMI_HI2CHCR, temp & ~HI2C_ENABLE_TRANSACTION);
+ HDMI_READ(HDMI_HI2CHCR);
+
+ i2c_dev->status = I2C_TRANSACTION_DONE;
+ return;
+}
+
+static irqreturn_t oaktrail_hdmi_i2c_handler(int this_irq, void *dev)
+{
+ struct oaktrail_hdmi_dev *hdmi_dev = dev;
+ struct hdmi_i2c_dev *i2c_dev = hdmi_dev->i2c_dev;
+ u32 stat;
+
+ stat = HDMI_READ(HDMI_HISR);
+
+ if (stat & HDMI_INTR_HPD) {
+ HDMI_WRITE(HDMI_HISR, stat | HDMI_INTR_HPD);
+ HDMI_READ(HDMI_HISR);
+ }
+
+ if (stat & HDMI_INTR_I2C_FULL)
+ hdmi_i2c_read(hdmi_dev);
+
+ if (stat & HDMI_INTR_I2C_DONE)
+ hdmi_i2c_transaction_done(hdmi_dev);
+
+ complete(&i2c_dev->complete);
+
+ return IRQ_HANDLED;
+}
+
+/*
+ * choose alternate function 2 of GPIO pin 52, 53,
+ * which is used by HDMI I2C logic
+ */
+static void oaktrail_hdmi_i2c_gpio_fix(void)
+{
+ void *base;
+ unsigned int gpio_base = 0xff12c000;
+ int gpio_len = 0x1000;
+ u32 temp;
+
+ base = ioremap((resource_size_t)gpio_base, gpio_len);
+ if (base == NULL) {
+ DRM_ERROR("gpio ioremap fail\n");
+ return;
+ }
+
+ temp = readl(base + 0x44);
+ DRM_DEBUG_DRIVER("old gpio val %x\n", temp);
+ writel((temp | 0x00000a00), (base + 0x44));
+ temp = readl(base + 0x44);
+ DRM_DEBUG_DRIVER("new gpio val %x\n", temp);
+
+ iounmap(base);
+}
+
+int oaktrail_hdmi_i2c_init(struct pci_dev *dev)
+{
+ struct oaktrail_hdmi_dev *hdmi_dev;
+ struct hdmi_i2c_dev *i2c_dev;
+ int ret;
+
+ hdmi_dev = pci_get_drvdata(dev);
+
+ i2c_dev = kzalloc(sizeof(struct hdmi_i2c_dev), GFP_KERNEL);
+ if (i2c_dev == NULL) {
+ DRM_ERROR("Can't allocate interface\n");
+ ret = -ENOMEM;
+ goto exit;
+ }
+
+ i2c_dev->adap = &oaktrail_hdmi_i2c_adapter;
+ i2c_dev->status = I2C_STAT_INIT;
+ init_completion(&i2c_dev->complete);
+ mutex_init(&i2c_dev->i2c_lock);
+ i2c_set_adapdata(&oaktrail_hdmi_i2c_adapter, hdmi_dev);
+ hdmi_dev->i2c_dev = i2c_dev;
+
+ /* Enable HDMI I2C function on gpio */
+ oaktrail_hdmi_i2c_gpio_fix();
+
+ /* request irq */
+ ret = request_irq(dev->irq, oaktrail_hdmi_i2c_handler, IRQF_SHARED,
+ oaktrail_hdmi_i2c_adapter.name, hdmi_dev);
+ if (ret) {
+ DRM_ERROR("Failed to request IRQ for I2C controller\n");
+ goto err;
+ }
+
+ /* Adapter registration */
+ ret = i2c_add_numbered_adapter(&oaktrail_hdmi_i2c_adapter);
+ return ret;
+
+err:
+ kfree(i2c_dev);
+exit:
+ return ret;
+}
+
+void oaktrail_hdmi_i2c_exit(struct pci_dev *dev)
+{
+ struct oaktrail_hdmi_dev *hdmi_dev;
+ struct hdmi_i2c_dev *i2c_dev;
+
+ hdmi_dev = pci_get_drvdata(dev);
+ if (i2c_del_adapter(&oaktrail_hdmi_i2c_adapter))
+ DRM_DEBUG_DRIVER("Failed to delete hdmi-i2c adapter\n");
+
+ i2c_dev = hdmi_dev->i2c_dev;
+ kfree(i2c_dev);
+ free_irq(dev->irq, hdmi_dev);
+}
diff --git a/drivers/gpu/drm/gma500/oaktrail_lvds.c b/drivers/gpu/drm/gma500/oaktrail_lvds.c
new file mode 100644
index 0000000..a552226
--- /dev/null
+++ b/drivers/gpu/drm/gma500/oaktrail_lvds.c
@@ -0,0 +1,406 @@
+/*
+ * Copyright © 2006-2009 Intel Corporation
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms and conditions of the GNU General Public License,
+ * version 2, as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope it will be useful, but WITHOUT
+ * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+ * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for
+ * more details.
+ *
+ * You should have received a copy of the GNU General Public License along with
+ * this program; if not, write to the Free Software Foundation, Inc.,
+ * 51 Franklin St - Fifth Floor, Boston, MA 02110-1301 USA.
+ *
+ * Authors:
+ * Eric Anholt <eric@xxxxxxxxxx>
+ * Dave Airlie <airlied@xxxxxxxx>
+ * Jesse Barnes <jesse.barnes@xxxxxxxxx>
+ */
+
+#include <linux/i2c.h>
+#include <drm/drmP.h>
+#include <asm/mrst.h>
+
+#include "intel_bios.h"
+#include "psb_drv.h"
+#include "psb_intel_drv.h"
+#include "psb_intel_reg.h"
+#include "power.h"
+#include <linux/pm_runtime.h>
+
+/* The max/min PWM frequency in BPCR[31:17] - */
+/* The smallest number is 1 (not 0) that can fit in the
+ * 15-bit field of the and then*/
+/* shifts to the left by one bit to get the actual 16-bit
+ * value that the 15-bits correspond to.*/
+#define MRST_BLC_MAX_PWM_REG_FREQ 0xFFFF
+#define BRIGHTNESS_MAX_LEVEL 100
+
+/**
+ * Sets the power state for the panel.
+ */
+static void oaktrail_lvds_set_power(struct drm_device *dev,
+ struct psb_intel_output *output, bool on)
+{
+ u32 pp_status;
+ struct drm_psb_private *dev_priv = dev->dev_private;
+
+ if (!gma_power_begin(dev, true))
+ return;
+
+ if (on) {
+ REG_WRITE(PP_CONTROL, REG_READ(PP_CONTROL) |
+ POWER_TARGET_ON);
+ do {
+ pp_status = REG_READ(PP_STATUS);
+ } while ((pp_status & (PP_ON | PP_READY)) == PP_READY);
+ dev_priv->is_lvds_on = true;
+ if (dev_priv->ops->lvds_bl_power)
+ dev_priv->ops->lvds_bl_power(dev, true);
+ } else {
+ if (dev_priv->ops->lvds_bl_power)
+ dev_priv->ops->lvds_bl_power(dev, false);
+ REG_WRITE(PP_CONTROL, REG_READ(PP_CONTROL) &
+ ~POWER_TARGET_ON);
+ do {
+ pp_status = REG_READ(PP_STATUS);
+ } while (pp_status & PP_ON);
+ dev_priv->is_lvds_on = false;
+ pm_request_idle(&dev->pdev->dev);
+ }
+ gma_power_end(dev);
+}
+
+static void oaktrail_lvds_dpms(struct drm_encoder *encoder, int mode)
+{
+ struct drm_device *dev = encoder->dev;
+ struct psb_intel_output *output = enc_to_psb_intel_output(encoder);
+
+ if (mode == DRM_MODE_DPMS_ON)
+ oaktrail_lvds_set_power(dev, output, true);
+ else
+ oaktrail_lvds_set_power(dev, output, false);
+
+ /* XXX: We never power down the LVDS pairs. */
+}
+
+static void oaktrail_lvds_mode_set(struct drm_encoder *encoder,
+ struct drm_display_mode *mode,
+ struct drm_display_mode *adjusted_mode)
+{
+ struct psb_intel_mode_device *mode_dev =
+ enc_to_psb_intel_output(encoder)->mode_dev;
+ struct drm_device *dev = encoder->dev;
+ struct drm_psb_private *dev_priv = dev->dev_private;
+ u32 lvds_port;
+ uint64_t v = DRM_MODE_SCALE_FULLSCREEN;
+
+ if (!gma_power_begin(dev, true))
+ return;
+
+ /*
+ * The LVDS pin pair will already have been turned on in the
+ * psb_intel_crtc_mode_set since it has a large impact on the DPLL
+ * settings.
+ */
+ lvds_port = (REG_READ(LVDS) &
+ (~LVDS_PIPEB_SELECT)) |
+ LVDS_PORT_EN |
+ LVDS_BORDER_EN;
+
+ /* If the firmware says dither on Moorestown, or the BIOS does
+ on Oaktrail then enable dithering */
+ if (mode_dev->panel_wants_dither || dev_priv->lvds_dither)
+ lvds_port |= MRST_PANEL_8TO6_DITHER_ENABLE;
+
+ REG_WRITE(LVDS, lvds_port);
+
+ drm_connector_property_get_value(
+ &enc_to_psb_intel_output(encoder)->base,
+ dev->mode_config.scaling_mode_property,
+ &v);
+
+ if (v == DRM_MODE_SCALE_NO_SCALE)
+ REG_WRITE(PFIT_CONTROL, 0);
+ else if (v == DRM_MODE_SCALE_ASPECT) {
+ if ((mode->vdisplay != adjusted_mode->crtc_vdisplay) ||
+ (mode->hdisplay != adjusted_mode->crtc_hdisplay)) {
+ if ((adjusted_mode->crtc_hdisplay * mode->vdisplay) ==
+ (mode->hdisplay * adjusted_mode->crtc_vdisplay))
+ REG_WRITE(PFIT_CONTROL, PFIT_ENABLE);
+ else if ((adjusted_mode->crtc_hdisplay *
+ mode->vdisplay) > (mode->hdisplay *
+ adjusted_mode->crtc_vdisplay))
+ REG_WRITE(PFIT_CONTROL, PFIT_ENABLE |
+ PFIT_SCALING_MODE_PILLARBOX);
+ else
+ REG_WRITE(PFIT_CONTROL, PFIT_ENABLE |
+ PFIT_SCALING_MODE_LETTERBOX);
+ } else
+ REG_WRITE(PFIT_CONTROL, PFIT_ENABLE);
+ } else /*(v == DRM_MODE_SCALE_FULLSCREEN)*/
+ REG_WRITE(PFIT_CONTROL, PFIT_ENABLE);
+
+ gma_power_end(dev);
+}
+
+static void oaktrail_lvds_prepare(struct drm_encoder *encoder)
+{
+ struct drm_device *dev = encoder->dev;
+ struct psb_intel_output *output = enc_to_psb_intel_output(encoder);
+ struct psb_intel_mode_device *mode_dev = output->mode_dev;
+
+ if (!gma_power_begin(dev, true))
+ return;
+
+ mode_dev->saveBLC_PWM_CTL = REG_READ(BLC_PWM_CTL);
+ mode_dev->backlight_duty_cycle = (mode_dev->saveBLC_PWM_CTL &
+ BACKLIGHT_DUTY_CYCLE_MASK);
+ oaktrail_lvds_set_power(dev, output, false);
+ gma_power_end(dev);
+}
+
+static u32 oaktrail_lvds_get_max_backlight(struct drm_device *dev)
+{
+ struct drm_psb_private *dev_priv = dev->dev_private;
+ u32 ret;
+
+ if (gma_power_begin(dev, false)) {
+ ret = ((REG_READ(BLC_PWM_CTL) &
+ BACKLIGHT_MODULATION_FREQ_MASK) >>
+ BACKLIGHT_MODULATION_FREQ_SHIFT) * 2;
+
+ gma_power_end(dev);
+ } else
+ ret = ((dev_priv->saveBLC_PWM_CTL &
+ BACKLIGHT_MODULATION_FREQ_MASK) >>
+ BACKLIGHT_MODULATION_FREQ_SHIFT) * 2;
+
+ return ret;
+}
+
+static void oaktrail_lvds_commit(struct drm_encoder *encoder)
+{
+ struct drm_device *dev = encoder->dev;
+ struct psb_intel_output *output = enc_to_psb_intel_output(encoder);
+ struct psb_intel_mode_device *mode_dev = output->mode_dev;
+
+ if (mode_dev->backlight_duty_cycle == 0)
+ mode_dev->backlight_duty_cycle =
+ oaktrail_lvds_get_max_backlight(dev);
+ oaktrail_lvds_set_power(dev, output, true);
+}
+
+static const struct drm_encoder_helper_funcs oaktrail_lvds_helper_funcs = {
+ .dpms = oaktrail_lvds_dpms,
+ .mode_fixup = psb_intel_lvds_mode_fixup,
+ .prepare = oaktrail_lvds_prepare,
+ .mode_set = oaktrail_lvds_mode_set,
+ .commit = oaktrail_lvds_commit,
+};
+
+static struct drm_display_mode lvds_configuration_modes[] = {
+ /* hard coded fixed mode for TPO LTPS LPJ040K001A */
+ { DRM_MODE("800x480", DRM_MODE_TYPE_DRIVER, 33264, 800, 836,
+ 846, 1056, 0, 480, 489, 491, 525, 0, 0) },
+ /* hard coded fixed mode for LVDS 800x480 */
+ { DRM_MODE("800x480", DRM_MODE_TYPE_DRIVER, 30994, 800, 801,
+ 802, 1024, 0, 480, 481, 482, 525, 0, 0) },
+ /* hard coded fixed mode for Samsung 480wsvga LVDS 1024x600@75 */
+ { DRM_MODE("1024x600", DRM_MODE_TYPE_DRIVER, 53990, 1024, 1072,
+ 1104, 1184, 0, 600, 603, 604, 608, 0, 0) },
+ /* hard coded fixed mode for Samsung 480wsvga LVDS 1024x600@75 */
+ { DRM_MODE("1024x600", DRM_MODE_TYPE_DRIVER, 53990, 1024, 1104,
+ 1136, 1184, 0, 600, 603, 604, 608, 0, 0) },
+ /* hard coded fixed mode for Sharp wsvga LVDS 1024x600 */
+ { DRM_MODE("1024x600", DRM_MODE_TYPE_DRIVER, 48885, 1024, 1124,
+ 1204, 1312, 0, 600, 607, 610, 621, 0, 0) },
+ /* hard coded fixed mode for LVDS 1024x768 */
+ { DRM_MODE("1024x768", DRM_MODE_TYPE_DRIVER, 65000, 1024, 1048,
+ 1184, 1344, 0, 768, 771, 777, 806, 0, 0) },
+ /* hard coded fixed mode for LVDS 1366x768 */
+ { DRM_MODE("1366x768", DRM_MODE_TYPE_DRIVER, 77500, 1366, 1430,
+ 1558, 1664, 0, 768, 769, 770, 776, 0, 0) },
+};
+
+/* Returns the panel fixed mode from configuration. */
+
+static struct drm_display_mode *
+oaktrail_lvds_get_configuration_mode(struct drm_device *dev)
+{
+ struct drm_display_mode *mode = NULL;
+ struct drm_psb_private *dev_priv = dev->dev_private;
+ struct oaktrail_timing_info *ti = &dev_priv->gct_data.DTD;
+
+ if (dev_priv->vbt_data.size != 0x00) { /*if non-zero, then use vbt*/
+ mode = kzalloc(sizeof(*mode), GFP_KERNEL);
+ if (!mode)
+ return NULL;
+
+ mode->hdisplay = (ti->hactive_hi << 8) | ti->hactive_lo;
+ mode->vdisplay = (ti->vactive_hi << 8) | ti->vactive_lo;
+ mode->hsync_start = mode->hdisplay + \
+ ((ti->hsync_offset_hi << 8) | \
+ ti->hsync_offset_lo);
+ mode->hsync_end = mode->hsync_start + \
+ ((ti->hsync_pulse_width_hi << 8) | \
+ ti->hsync_pulse_width_lo);
+ mode->htotal = mode->hdisplay + ((ti->hblank_hi << 8) | \
+ ti->hblank_lo);
+ mode->vsync_start = \
+ mode->vdisplay + ((ti->vsync_offset_hi << 4) | \
+ ti->vsync_offset_lo);
+ mode->vsync_end = \
+ mode->vsync_start + ((ti->vsync_pulse_width_hi << 4) | \
+ ti->vsync_pulse_width_lo);
+ mode->vtotal = mode->vdisplay + \
+ ((ti->vblank_hi << 8) | ti->vblank_lo);
+ mode->clock = ti->pixel_clock * 10;
+#if 0
+ printk(KERN_INFO "hdisplay is %d\n", mode->hdisplay);
+ printk(KERN_INFO "vdisplay is %d\n", mode->vdisplay);
+ printk(KERN_INFO "HSS is %d\n", mode->hsync_start);
+ printk(KERN_INFO "HSE is %d\n", mode->hsync_end);
+ printk(KERN_INFO "htotal is %d\n", mode->htotal);
+ printk(KERN_INFO "VSS is %d\n", mode->vsync_start);
+ printk(KERN_INFO "VSE is %d\n", mode->vsync_end);
+ printk(KERN_INFO "vtotal is %d\n", mode->vtotal);
+ printk(KERN_INFO "clock is %d\n", mode->clock);
+#endif
+ } else
+ mode = drm_mode_duplicate(dev, &lvds_configuration_modes[2]);
+
+ drm_mode_set_name(mode);
+ drm_mode_set_crtcinfo(mode, 0);
+
+ return mode;
+}
+
+/**
+ * oaktrail_lvds_init - setup LVDS connectors on this device
+ * @dev: drm device
+ *
+ * Create the connector, register the LVDS DDC bus, and try to figure out what
+ * modes we can display on the LVDS panel (if present).
+ */
+void oaktrail_lvds_init(struct drm_device *dev,
+ struct psb_intel_mode_device *mode_dev)
+{
+ struct psb_intel_output *psb_intel_output;
+ struct drm_connector *connector;
+ struct drm_encoder *encoder;
+ struct drm_psb_private *dev_priv =
+ (struct drm_psb_private *) dev->dev_private;
+ struct edid *edid;
+ int ret = 0;
+ struct i2c_adapter *i2c_adap;
+ struct drm_display_mode *scan; /* *modes, *bios_mode; */
+
+ psb_intel_output = kzalloc(sizeof(struct psb_intel_output), GFP_KERNEL);
+ if (!psb_intel_output)
+ return;
+
+ psb_intel_output->mode_dev = mode_dev;
+ connector = &psb_intel_output->base;
+ encoder = &psb_intel_output->enc;
+ dev_priv->is_lvds_on = true;
+ drm_connector_init(dev, &psb_intel_output->base,
+ &psb_intel_lvds_connector_funcs,
+ DRM_MODE_CONNECTOR_LVDS);
+
+ drm_encoder_init(dev, &psb_intel_output->enc, &psb_intel_lvds_enc_funcs,
+ DRM_MODE_ENCODER_LVDS);
+
+ drm_mode_connector_attach_encoder(&psb_intel_output->base,
+ &psb_intel_output->enc);
+ psb_intel_output->type = INTEL_OUTPUT_LVDS;
+
+ drm_encoder_helper_add(encoder, &oaktrail_lvds_helper_funcs);
+ drm_connector_helper_add(connector,
+ &psb_intel_lvds_connector_helper_funcs);
+ connector->display_info.subpixel_order = SubPixelHorizontalRGB;
+ connector->interlace_allowed = false;
+ connector->doublescan_allowed = false;
+
+ drm_connector_attach_property(connector,
+ dev->mode_config.scaling_mode_property,
+ DRM_MODE_SCALE_FULLSCREEN);
+ drm_connector_attach_property(connector,
+ dev_priv->backlight_property,
+ BRIGHTNESS_MAX_LEVEL);
+
+ mode_dev->panel_wants_dither = false;
+ if (dev_priv->vbt_data.size != 0x00)
+ mode_dev->panel_wants_dither = (dev_priv->gct_data.
+ Panel_Port_Control & MRST_PANEL_8TO6_DITHER_ENABLE);
+
+ /*
+ * LVDS discovery:
+ * 1) check for EDID on DDC
+ * 2) check for VBT data
+ * 3) check to see if LVDS is already on
+ * if none of the above, no panel
+ * 4) make sure lid is open
+ * if closed, act like it's not there for now
+ */
+
+ i2c_adap = i2c_get_adapter(dev_priv->ops->i2c_bus);
+ if (i2c_adap == NULL)
+ dev_err(dev->dev, "No ddc adapter available!\n");
+ /*
+ * Attempt to get the fixed panel mode from DDC. Assume that the
+ * preferred mode is the right one.
+ */
+ if (i2c_adap) {
+ edid = drm_get_edid(connector, i2c_adap);
+ if (edid) {
+ drm_mode_connector_update_edid_property(connector,
+ edid);
+ ret = drm_add_edid_modes(connector, edid);
+ kfree(edid);
+ }
+
+ list_for_each_entry(scan, &connector->probed_modes, head) {
+ if (scan->type & DRM_MODE_TYPE_PREFERRED) {
+ mode_dev->panel_fixed_mode =
+ drm_mode_duplicate(dev, scan);
+ goto out; /* FIXME: check for quirks */
+ }
+ }
+ }
+ /*
+ * If we didn't get EDID, try geting panel timing
+ * from configuration data
+ */
+ mode_dev->panel_fixed_mode = oaktrail_lvds_get_configuration_mode(dev);
+
+ if (mode_dev->panel_fixed_mode) {
+ mode_dev->panel_fixed_mode->type |= DRM_MODE_TYPE_PREFERRED;
+ goto out; /* FIXME: check for quirks */
+ }
+
+ /* If we still don't have a mode after all that, give up. */
+ if (!mode_dev->panel_fixed_mode) {
+ dev_err(dev->dev, "Found no modes on the lvds, ignoring the LVDS\n");
+ goto failed_find;
+ }
+
+out:
+ drm_sysfs_connector_add(connector);
+ return;
+
+failed_find:
+ dev_dbg(dev->dev, "No LVDS modes found, disabling.\n");
+ if (psb_intel_output->ddc_bus)
+ psb_intel_i2c_destroy(psb_intel_output->ddc_bus);
+
+/* failed_ddc: */
+
+ drm_encoder_cleanup(encoder);
+ drm_connector_cleanup(connector);
+ kfree(connector);
+}
+
_______________________________________________
dri-devel mailing list
dri-devel@xxxxxxxxxxxxxxxxxxxxx
http://lists.freedesktop.org/mailman/listinfo/dri-devel
