Re: [PATCH v2 2/3] drm/rockchip: Add ROCKCHIP DW MIPI DSI controller driver

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



Hi Archit,


On 2017年11月28日 14:27, Archit Taneja wrote:
Hi,

Thanks a lot for working on this. Some comments below.

Those comments have fixed in patch_v3 https://patchwork.kernel.org/patch/10079857/
Thanks for review.
On 11/28/2017 07:25 AM, Nickey Yang wrote:
Add the ROCKCHIP DSI controller driver that uses the Synopsys DesignWare
MIPI DSI host controller bridge.

Signed-off-by: Nickey Yang <nickey.yang@xxxxxxxxxxxxxx>
---
  drivers/gpu/drm/rockchip/Kconfig                |    2 +-
  drivers/gpu/drm/rockchip/Makefile               |    2 +-
  drivers/gpu/drm/rockchip/dw-mipi-dsi.c          | 1349 -----------------------
  drivers/gpu/drm/rockchip/dw-mipi-dsi_rockchip.c |  756 +++++++++++++
  drivers/gpu/drm/rockchip/rockchip_drm_drv.c     |    2 +-
  drivers/gpu/drm/rockchip/rockchip_drm_drv.h     |    2 +-
  6 files changed, 760 insertions(+), 1353 deletions(-)
  delete mode 100644 drivers/gpu/drm/rockchip/dw-mipi-dsi.c
  create mode 100644 drivers/gpu/drm/rockchip/dw-mipi-dsi_rockchip.c

diff --git a/drivers/gpu/drm/rockchip/Kconfig b/drivers/gpu/drm/rockchip/Kconfig
index 0ccc762..9eb4795 100644
--- a/drivers/gpu/drm/rockchip/Kconfig
+++ b/drivers/gpu/drm/rockchip/Kconfig
@@ -7,7 +7,7 @@ config DRM_ROCKCHIP
      select VIDEOMODE_HELPERS
      select DRM_ANALOGIX_DP if ROCKCHIP_ANALOGIX_DP
      select DRM_DW_HDMI if ROCKCHIP_DW_HDMI
-    select DRM_MIPI_DSI if ROCKCHIP_DW_MIPI_DSI
+    select DRM_DW_MIPI_DSI if ROCKCHIP_DW_MIPI_DSI
      select SND_SOC_HDMI_CODEC if ROCKCHIP_CDN_DP && SND_SOC
      help
        Choose this option if you have a Rockchip soc chipset.
diff --git a/drivers/gpu/drm/rockchip/Makefile b/drivers/gpu/drm/rockchip/Makefile
index a314e21..c05fe47 100644
--- a/drivers/gpu/drm/rockchip/Makefile
+++ b/drivers/gpu/drm/rockchip/Makefile
@@ -11,7 +11,7 @@ rockchipdrm-$(CONFIG_DRM_FBDEV_EMULATION) += rockchip_drm_fbdev.o
  rockchipdrm-$(CONFIG_ROCKCHIP_ANALOGIX_DP) += analogix_dp-rockchip.o
  rockchipdrm-$(CONFIG_ROCKCHIP_CDN_DP) += cdn-dp-core.o cdn-dp-reg.o
  rockchipdrm-$(CONFIG_ROCKCHIP_DW_HDMI) += dw_hdmi-rockchip.o
-rockchipdrm-$(CONFIG_ROCKCHIP_DW_MIPI_DSI) += dw-mipi-dsi.o
+rockchipdrm-$(CONFIG_ROCKCHIP_DW_MIPI_DSI) += dw-mipi-dsi_rockchip.o
  rockchipdrm-$(CONFIG_ROCKCHIP_INNO_HDMI) += inno_hdmi.o
  rockchipdrm-$(CONFIG_ROCKCHIP_LVDS) += rockchip_lvds.o
  diff --git a/drivers/gpu/drm/rockchip/dw-mipi-dsi.c b/drivers/gpu/drm/rockchip/dw-mipi-dsi.c
deleted file mode 100644
index b15755b..0000000
--- a/drivers/gpu/drm/rockchip/dw-mipi-dsi.c
+++ /dev/null
@@ -1,1349 +0,0 @@
-/*
- * Copyright (c) 2016, Fuzhou Rockchip Electronics Co., Ltd
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- */
-#include <linux/clk.h>
-#include <linux/component.h>
-#include <linux/iopoll.h>
-#include <linux/math64.h>
-#include <linux/module.h>
-#include <linux/of_device.h>
-#include <linux/pm_runtime.h>
-#include <linux/regmap.h>
-#include <linux/reset.h>
-#include <linux/mfd/syscon.h>
-#include <drm/drm_atomic_helper.h>
-#include <drm/drm_crtc.h>
-#include <drm/drm_crtc_helper.h>
-#include <drm/drm_mipi_dsi.h>
-#include <drm/drm_of.h>
-#include <drm/drm_panel.h>
-#include <drm/drmP.h>
-#include <video/mipi_display.h>
-
-#include "rockchip_drm_drv.h"
-#include "rockchip_drm_vop.h"
-
-#define DRIVER_NAME    "dw-mipi-dsi"
-
-#define RK3288_GRF_SOC_CON6        0x025c
-#define RK3288_DSI0_SEL_VOP_LIT        BIT(6)
-#define RK3288_DSI1_SEL_VOP_LIT        BIT(9)
-
-#define RK3399_GRF_SOC_CON20        0x6250
-#define RK3399_DSI0_SEL_VOP_LIT        BIT(0)
-#define RK3399_DSI1_SEL_VOP_LIT        BIT(4)
-
-/* disable turnrequest, turndisable, forcetxstopmode, forcerxmode */
-#define RK3399_GRF_SOC_CON22        0x6258
-#define RK3399_GRF_DSI_MODE        0xffff0000
-
-#define DSI_VERSION            0x00
-#define DSI_PWR_UP            0x04
-#define RESET                0
-#define POWERUP                BIT(0)
-
-#define DSI_CLKMGR_CFG            0x08
-#define TO_CLK_DIVIDSION(div)        (((div) & 0xff) << 8)
-#define TX_ESC_CLK_DIVIDSION(div)    (((div) & 0xff) << 0)
-
-#define DSI_DPI_VCID            0x0c
-#define DPI_VID(vid)            (((vid) & 0x3) << 0)
-
-#define DSI_DPI_COLOR_CODING        0x10
-#define EN18_LOOSELY            BIT(8)
-#define DPI_COLOR_CODING_16BIT_1    0x0
-#define DPI_COLOR_CODING_16BIT_2    0x1
-#define DPI_COLOR_CODING_16BIT_3    0x2
-#define DPI_COLOR_CODING_18BIT_1    0x3
-#define DPI_COLOR_CODING_18BIT_2    0x4
-#define DPI_COLOR_CODING_24BIT        0x5
-
-#define DSI_DPI_CFG_POL            0x14
-#define COLORM_ACTIVE_LOW        BIT(4)
-#define SHUTD_ACTIVE_LOW        BIT(3)
-#define HSYNC_ACTIVE_LOW        BIT(2)
-#define VSYNC_ACTIVE_LOW        BIT(1)
-#define DATAEN_ACTIVE_LOW        BIT(0)
-
-#define DSI_DPI_LP_CMD_TIM        0x18
-#define OUTVACT_LPCMD_TIME(p)        (((p) & 0xff) << 16)
-#define INVACT_LPCMD_TIME(p)        ((p) & 0xff)
-
-#define DSI_DBI_CFG            0x20
-#define DSI_DBI_CMDSIZE            0x28
-
-#define DSI_PCKHDL_CFG            0x2c
-#define EN_CRC_RX            BIT(4)
-#define EN_ECC_RX            BIT(3)
-#define EN_BTA                BIT(2)
-#define EN_EOTP_RX            BIT(1)
-#define EN_EOTP_TX            BIT(0)
-
-#define DSI_MODE_CFG            0x34
-#define ENABLE_VIDEO_MODE        0
-#define ENABLE_CMD_MODE            BIT(0)
-
-#define DSI_VID_MODE_CFG        0x38
-#define FRAME_BTA_ACK            BIT(14)
-#define ENABLE_LOW_POWER        (0x3f << 8)
-#define ENABLE_LOW_POWER_MASK        (0x3f << 8)
-#define VID_MODE_TYPE_NON_BURST_SYNC_PULSES    0x0
-#define VID_MODE_TYPE_NON_BURST_SYNC_EVENTS    0x1
-#define VID_MODE_TYPE_BURST            0x2
-#define VID_MODE_TYPE_MASK            0x3
-
-#define DSI_VID_PKT_SIZE        0x3c
-#define VID_PKT_SIZE(p)            (((p) & 0x3fff) << 0)
-#define VID_PKT_MAX_SIZE        0x3fff
-
-#define DSI_VID_HSA_TIME        0x48
-#define DSI_VID_HBP_TIME        0x4c
-#define DSI_VID_HLINE_TIME        0x50
-#define DSI_VID_VSA_LINES        0x54
-#define DSI_VID_VBP_LINES        0x58
-#define DSI_VID_VFP_LINES        0x5c
-#define DSI_VID_VACTIVE_LINES        0x60
-#define DSI_CMD_MODE_CFG        0x68
-#define MAX_RD_PKT_SIZE_LP        BIT(24)
-#define DCS_LW_TX_LP            BIT(19)
-#define DCS_SR_0P_TX_LP            BIT(18)
-#define DCS_SW_1P_TX_LP            BIT(17)
-#define DCS_SW_0P_TX_LP            BIT(16)
-#define GEN_LW_TX_LP            BIT(14)
-#define GEN_SR_2P_TX_LP            BIT(13)
-#define GEN_SR_1P_TX_LP            BIT(12)
-#define GEN_SR_0P_TX_LP            BIT(11)
-#define GEN_SW_2P_TX_LP            BIT(10)
-#define GEN_SW_1P_TX_LP            BIT(9)
-#define GEN_SW_0P_TX_LP            BIT(8)
-#define EN_ACK_RQST            BIT(1)
-#define EN_TEAR_FX            BIT(0)
-
-#define CMD_MODE_ALL_LP            (MAX_RD_PKT_SIZE_LP | \
-                     DCS_LW_TX_LP | \
-                     DCS_SR_0P_TX_LP | \
-                     DCS_SW_1P_TX_LP | \
-                     DCS_SW_0P_TX_LP | \
-                     GEN_LW_TX_LP | \
-                     GEN_SR_2P_TX_LP | \
-                     GEN_SR_1P_TX_LP | \
-                     GEN_SR_0P_TX_LP | \
-                     GEN_SW_2P_TX_LP | \
-                     GEN_SW_1P_TX_LP | \
-                     GEN_SW_0P_TX_LP)
-
-#define DSI_GEN_HDR            0x6c
-#define GEN_HDATA(data)            (((data) & 0xffff) << 8)
-#define GEN_HDATA_MASK            (0xffff << 8)
-#define GEN_HTYPE(type)            (((type) & 0xff) << 0)
-#define GEN_HTYPE_MASK            0xff
-
-#define DSI_GEN_PLD_DATA        0x70
-
-#define DSI_CMD_PKT_STATUS        0x74
-#define GEN_CMD_EMPTY            BIT(0)
-#define GEN_CMD_FULL            BIT(1)
-#define GEN_PLD_W_EMPTY            BIT(2)
-#define GEN_PLD_W_FULL            BIT(3)
-#define GEN_PLD_R_EMPTY            BIT(4)
-#define GEN_PLD_R_FULL            BIT(5)
-#define GEN_RD_CMD_BUSY            BIT(6)
-
-#define DSI_TO_CNT_CFG            0x78
-#define HSTX_TO_CNT(p)            (((p) & 0xffff) << 16)
-#define LPRX_TO_CNT(p)            ((p) & 0xffff)
-
-#define DSI_BTA_TO_CNT            0x8c
-#define DSI_LPCLK_CTRL            0x94
-#define AUTO_CLKLANE_CTRL        BIT(1)
-#define PHY_TXREQUESTCLKHS        BIT(0)
-
-#define DSI_PHY_TMR_LPCLK_CFG        0x98
-#define PHY_CLKHS2LP_TIME(lbcc)        (((lbcc) & 0x3ff) << 16)
-#define PHY_CLKLP2HS_TIME(lbcc)        ((lbcc) & 0x3ff)
-
-#define DSI_PHY_TMR_CFG            0x9c
-#define PHY_HS2LP_TIME(lbcc)        (((lbcc) & 0xff) << 24)
-#define PHY_LP2HS_TIME(lbcc)        (((lbcc) & 0xff) << 16)
-#define MAX_RD_TIME(lbcc)        ((lbcc) & 0x7fff)
-
-#define DSI_PHY_RSTZ            0xa0
-#define PHY_DISFORCEPLL            0
-#define PHY_ENFORCEPLL            BIT(3)
-#define PHY_DISABLECLK            0
-#define PHY_ENABLECLK            BIT(2)
-#define PHY_RSTZ            0
-#define PHY_UNRSTZ            BIT(1)
-#define PHY_SHUTDOWNZ            0
-#define PHY_UNSHUTDOWNZ            BIT(0)
-
-#define DSI_PHY_IF_CFG            0xa4
-#define N_LANES(n)            ((((n) - 1) & 0x3) << 0)
-#define PHY_STOP_WAIT_TIME(cycle)    (((cycle) & 0xff) << 8)
-
-#define DSI_PHY_STATUS            0xb0
-#define LOCK                BIT(0)
-#define STOP_STATE_CLK_LANE        BIT(2)
-
-#define DSI_PHY_TST_CTRL0        0xb4
-#define PHY_TESTCLK            BIT(1)
-#define PHY_UNTESTCLK            0
-#define PHY_TESTCLR            BIT(0)
-#define PHY_UNTESTCLR            0
-
-#define DSI_PHY_TST_CTRL1        0xb8
-#define PHY_TESTEN            BIT(16)
-#define PHY_UNTESTEN            0
-#define PHY_TESTDOUT(n)            (((n) & 0xff) << 8)
-#define PHY_TESTDIN(n)            (((n) & 0xff) << 0)
-
-#define DSI_INT_ST0            0xbc
-#define DSI_INT_ST1            0xc0
-#define DSI_INT_MSK0            0xc4
-#define DSI_INT_MSK1            0xc8
-
-#define PHY_STATUS_TIMEOUT_US        10000
-#define CMD_PKT_STATUS_TIMEOUT_US    20000
-
-#define BYPASS_VCO_RANGE    BIT(7)
-#define VCO_RANGE_CON_SEL(val)    (((val) & 0x7) << 3)
-#define VCO_IN_CAP_CON_DEFAULT    (0x0 << 1)
-#define VCO_IN_CAP_CON_LOW    (0x1 << 1)
-#define VCO_IN_CAP_CON_HIGH    (0x2 << 1)
-#define REF_BIAS_CUR_SEL    BIT(0)
-
-#define CP_CURRENT_3MA        BIT(3)
-#define CP_PROGRAM_EN        BIT(7)
-#define LPF_PROGRAM_EN        BIT(6)
-#define LPF_RESISTORS_20_KOHM    0
-
-#define HSFREQRANGE_SEL(val)    (((val) & 0x3f) << 1)
-
-#define INPUT_DIVIDER(val)    (((val) - 1) & 0x7f)
-#define LOW_PROGRAM_EN        0
-#define HIGH_PROGRAM_EN        BIT(7)
-#define LOOP_DIV_LOW_SEL(val)    (((val) - 1) & 0x1f)
-#define LOOP_DIV_HIGH_SEL(val)    ((((val) - 1) >> 5) & 0x1f)
-#define PLL_LOOP_DIV_EN        BIT(5)
-#define PLL_INPUT_DIV_EN    BIT(4)
-
-#define POWER_CONTROL        BIT(6)
-#define INTERNAL_REG_CURRENT    BIT(3)
-#define BIAS_BLOCK_ON        BIT(2)
-#define BANDGAP_ON        BIT(0)
-
-#define TER_RESISTOR_HIGH    BIT(7)
-#define    TER_RESISTOR_LOW    0
-#define LEVEL_SHIFTERS_ON    BIT(6)
-#define TER_CAL_DONE        BIT(5)
-#define SETRD_MAX        (0x7 << 2)
-#define POWER_MANAGE        BIT(1)
-#define TER_RESISTORS_ON    BIT(0)
-
-#define BIASEXTR_SEL(val)    ((val) & 0x7)
-#define BANDGAP_SEL(val)    ((val) & 0x7)
-#define TLP_PROGRAM_EN        BIT(7)
-#define THS_PRE_PROGRAM_EN    BIT(7)
-#define THS_ZERO_PROGRAM_EN    BIT(6)
-
-#define DW_MIPI_NEEDS_PHY_CFG_CLK    BIT(0)
-#define DW_MIPI_NEEDS_GRF_CLK        BIT(1)
-
-enum {
-    BANDGAP_97_07,
-    BANDGAP_98_05,
-    BANDGAP_99_02,
-    BANDGAP_100_00,
-    BANDGAP_93_17,
-    BANDGAP_94_15,
-    BANDGAP_95_12,
-    BANDGAP_96_10,
-};
-
-enum {
-    BIASEXTR_87_1,
-    BIASEXTR_91_5,
-    BIASEXTR_95_9,
-    BIASEXTR_100,
-    BIASEXTR_105_94,
-    BIASEXTR_111_88,
-    BIASEXTR_118_8,
-    BIASEXTR_127_7,
-};
-
-struct dw_mipi_dsi_plat_data {
-    u32 dsi0_en_bit;
-    u32 dsi1_en_bit;
-    u32 grf_switch_reg;
-    u32 grf_dsi0_mode;
-    u32 grf_dsi0_mode_reg;
-    unsigned int flags;
-    unsigned int max_data_lanes;
-};
-
-struct dw_mipi_dsi {
-    struct drm_encoder encoder;
-    struct drm_connector connector;
-    struct mipi_dsi_host dsi_host;
-    struct drm_panel *panel;
-    struct device *dev;
-    struct regmap *grf_regmap;
-    void __iomem *base;
-
-    struct clk *grf_clk;
-    struct clk *pllref_clk;
-    struct clk *pclk;
-    struct clk *phy_cfg_clk;
-
-    int dpms_mode;
-    unsigned int lane_mbps; /* per lane */
-    u32 channel;
-    u32 lanes;
-    u32 format;
-    u16 input_div;
-    u16 feedback_div;
-    unsigned long mode_flags;
-
-    const struct dw_mipi_dsi_plat_data *pdata;
-};
-
-enum dw_mipi_dsi_mode {
-    DW_MIPI_DSI_CMD_MODE,
-    DW_MIPI_DSI_VID_MODE,
-};
-
-struct dphy_pll_testdin_map {
-    unsigned int max_mbps;
-    u8 testdin;
-};
-
-/* The table is based on 27MHz DPHY pll reference clock. */
-static const struct dphy_pll_testdin_map dptdin_map[] = {
-    {  90, 0x00}, { 100, 0x10}, { 110, 0x20}, { 130, 0x01},
-    { 140, 0x11}, { 150, 0x21}, { 170, 0x02}, { 180, 0x12},
-    { 200, 0x22}, { 220, 0x03}, { 240, 0x13}, { 250, 0x23},
-    { 270, 0x04}, { 300, 0x14}, { 330, 0x05}, { 360, 0x15},
-    { 400, 0x25}, { 450, 0x06}, { 500, 0x16}, { 550, 0x07},
-    { 600, 0x17}, { 650, 0x08}, { 700, 0x18}, { 750, 0x09},
-    { 800, 0x19}, { 850, 0x29}, { 900, 0x39}, { 950, 0x0a},
-    {1000, 0x1a}, {1050, 0x2a}, {1100, 0x3a}, {1150, 0x0b},
-    {1200, 0x1b}, {1250, 0x2b}, {1300, 0x3b}, {1350, 0x0c},
-    {1400, 0x1c}, {1450, 0x2c}, {1500, 0x3c}
-};
-
-static int max_mbps_to_testdin(unsigned int max_mbps)
-{
-    int i;
-
-    for (i = 0; i < ARRAY_SIZE(dptdin_map); i++)
-        if (dptdin_map[i].max_mbps > max_mbps)
-            return dptdin_map[i].testdin;
-
-    return -EINVAL;
-}
-
-/*
- * The controller should generate 2 frames before
- * preparing the peripheral.
- */
-static void dw_mipi_dsi_wait_for_two_frames(struct drm_display_mode *mode)
-{
-    int refresh, two_frames;
-
-    refresh = drm_mode_vrefresh(mode);
-    two_frames = DIV_ROUND_UP(MSEC_PER_SEC, refresh) * 2;
-    msleep(two_frames);
-}
-
-static inline struct dw_mipi_dsi *host_to_dsi(struct mipi_dsi_host *host)
-{
-    return container_of(host, struct dw_mipi_dsi, dsi_host);
-}
-
-static inline struct dw_mipi_dsi *con_to_dsi(struct drm_connector *con)
-{
-    return container_of(con, struct dw_mipi_dsi, connector);
-}
-
-static inline struct dw_mipi_dsi *encoder_to_dsi(struct drm_encoder *encoder)
-{
-    return container_of(encoder, struct dw_mipi_dsi, encoder);
-}
-
-static inline void dsi_write(struct dw_mipi_dsi *dsi, u32 reg, u32 val)
-{
-    writel(val, dsi->base + reg);
-}
-
-static inline u32 dsi_read(struct dw_mipi_dsi *dsi, u32 reg)
-{
-    return readl(dsi->base + reg);
-}
-
-static void dw_mipi_dsi_phy_write(struct dw_mipi_dsi *dsi, u8 test_code,
-                  u8 test_data)
-{
-    /*
-     * With the falling edge on TESTCLK, the TESTDIN[7:0] signal content
-     * is latched internally as the current test code. Test data is
-     * programmed internally by rising edge on TESTCLK.
-     */
-    dsi_write(dsi, DSI_PHY_TST_CTRL0, PHY_TESTCLK | PHY_UNTESTCLR);
-
-    dsi_write(dsi, DSI_PHY_TST_CTRL1, PHY_TESTEN | PHY_TESTDOUT(0) |
-                      PHY_TESTDIN(test_code));
-
-    dsi_write(dsi, DSI_PHY_TST_CTRL0, PHY_UNTESTCLK | PHY_UNTESTCLR);
-
-    dsi_write(dsi, DSI_PHY_TST_CTRL1, PHY_UNTESTEN | PHY_TESTDOUT(0) |
-                      PHY_TESTDIN(test_data));
-
-    dsi_write(dsi, DSI_PHY_TST_CTRL0, PHY_TESTCLK | PHY_UNTESTCLR);
-}
-
-/**
- * ns2bc - Nanoseconds to byte clock cycles
- */
-static inline unsigned int ns2bc(struct dw_mipi_dsi *dsi, int ns)
-{
-    return DIV_ROUND_UP(ns * dsi->lane_mbps / 8, 1000);
-}
-
-/**
- * ns2ui - Nanoseconds to UI time periods
- */
-static inline unsigned int ns2ui(struct dw_mipi_dsi *dsi, int ns)
-{
-    return DIV_ROUND_UP(ns * dsi->lane_mbps, 1000);
-}
-
-static int dw_mipi_dsi_phy_init(struct dw_mipi_dsi *dsi)
-{
-    int ret, testdin, vco, val;
-
-    vco = (dsi->lane_mbps < 200) ? 0 : (dsi->lane_mbps + 100) / 200;
-
-    testdin = max_mbps_to_testdin(dsi->lane_mbps);
-    if (testdin < 0) {
-        DRM_DEV_ERROR(dsi->dev,
-                  "failed to get testdin for %dmbps lane clock\n",
-                  dsi->lane_mbps);
-        return testdin;
-    }
-
-    /* Start by clearing PHY state */
-    dsi_write(dsi, DSI_PHY_TST_CTRL0, PHY_UNTESTCLR);
-    dsi_write(dsi, DSI_PHY_TST_CTRL0, PHY_TESTCLR);
-    dsi_write(dsi, DSI_PHY_TST_CTRL0, PHY_UNTESTCLR);
-
-    ret = clk_prepare_enable(dsi->phy_cfg_clk);
-    if (ret) {
-        DRM_DEV_ERROR(dsi->dev, "Failed to enable phy_cfg_clk\n");
-        return ret;
-    }
-
-    dw_mipi_dsi_phy_write(dsi, 0x10, BYPASS_VCO_RANGE |
-                     VCO_RANGE_CON_SEL(vco) |
-                     VCO_IN_CAP_CON_LOW |
-                     REF_BIAS_CUR_SEL);
-
-    dw_mipi_dsi_phy_write(dsi, 0x11, CP_CURRENT_3MA);
-    dw_mipi_dsi_phy_write(dsi, 0x12, CP_PROGRAM_EN | LPF_PROGRAM_EN |
-                     LPF_RESISTORS_20_KOHM);
-
-    dw_mipi_dsi_phy_write(dsi, 0x44, HSFREQRANGE_SEL(testdin));
-
-    dw_mipi_dsi_phy_write(dsi, 0x17, INPUT_DIVIDER(dsi->input_div));
-    dw_mipi_dsi_phy_write(dsi, 0x18, LOOP_DIV_LOW_SEL(dsi->feedback_div) |
-                     LOW_PROGRAM_EN);
-    dw_mipi_dsi_phy_write(dsi, 0x18, LOOP_DIV_HIGH_SEL(dsi->feedback_div) |
-                     HIGH_PROGRAM_EN);
-    dw_mipi_dsi_phy_write(dsi, 0x19, PLL_LOOP_DIV_EN | PLL_INPUT_DIV_EN);
-
-    dw_mipi_dsi_phy_write(dsi, 0x22, LOW_PROGRAM_EN |
-                     BIASEXTR_SEL(BIASEXTR_127_7));
-    dw_mipi_dsi_phy_write(dsi, 0x22, HIGH_PROGRAM_EN |
-                     BANDGAP_SEL(BANDGAP_96_10));
-
-    dw_mipi_dsi_phy_write(dsi, 0x20, POWER_CONTROL | INTERNAL_REG_CURRENT |
-                     BIAS_BLOCK_ON | BANDGAP_ON);
-
-    dw_mipi_dsi_phy_write(dsi, 0x21, TER_RESISTOR_LOW | TER_CAL_DONE |
-                     SETRD_MAX | TER_RESISTORS_ON);
-    dw_mipi_dsi_phy_write(dsi, 0x21, TER_RESISTOR_HIGH | LEVEL_SHIFTERS_ON |
-                     SETRD_MAX | POWER_MANAGE |
-                     TER_RESISTORS_ON);
-
-    dw_mipi_dsi_phy_write(dsi, 0x60, TLP_PROGRAM_EN | ns2bc(dsi, 500));
-    dw_mipi_dsi_phy_write(dsi, 0x61, THS_PRE_PROGRAM_EN | ns2ui(dsi, 40)); -    dw_mipi_dsi_phy_write(dsi, 0x62, THS_ZERO_PROGRAM_EN | ns2bc(dsi, 300)); -    dw_mipi_dsi_phy_write(dsi, 0x63, THS_PRE_PROGRAM_EN | ns2ui(dsi, 100));
-    dw_mipi_dsi_phy_write(dsi, 0x64, BIT(5) | ns2bc(dsi, 100));
-    dw_mipi_dsi_phy_write(dsi, 0x65, BIT(5) | (ns2bc(dsi, 60) + 7));
-
-    dw_mipi_dsi_phy_write(dsi, 0x70, TLP_PROGRAM_EN | ns2bc(dsi, 500));
-    dw_mipi_dsi_phy_write(dsi, 0x71,
-                  THS_PRE_PROGRAM_EN | (ns2ui(dsi, 50) + 5));
-    dw_mipi_dsi_phy_write(dsi, 0x72,
-                  THS_ZERO_PROGRAM_EN | (ns2bc(dsi, 140) + 2));
-    dw_mipi_dsi_phy_write(dsi, 0x73,
-                  THS_PRE_PROGRAM_EN | (ns2ui(dsi, 60) + 8));
-    dw_mipi_dsi_phy_write(dsi, 0x74, BIT(5) | ns2bc(dsi, 100));
-
-    dsi_write(dsi, DSI_PHY_RSTZ, PHY_ENFORCEPLL | PHY_ENABLECLK |
-                     PHY_UNRSTZ | PHY_UNSHUTDOWNZ);
-
-    ret = readl_poll_timeout(dsi->base + DSI_PHY_STATUS,
-                 val, val & LOCK, 1000, PHY_STATUS_TIMEOUT_US);
-    if (ret < 0) {
-        DRM_DEV_ERROR(dsi->dev, "failed to wait for phy lock state\n");
-        goto phy_init_end;
-    }
-
-    ret = readl_poll_timeout(dsi->base + DSI_PHY_STATUS,
-                 val, val & STOP_STATE_CLK_LANE, 1000,
-                 PHY_STATUS_TIMEOUT_US);
-    if (ret < 0)
-        DRM_DEV_ERROR(dsi->dev,
-                  "failed to wait for phy clk lane stop state\n");
-
-phy_init_end:
-    clk_disable_unprepare(dsi->phy_cfg_clk);
-
-    return ret;
-}
-
-static int dw_mipi_dsi_get_lane_bps(struct dw_mipi_dsi *dsi,
-                    struct drm_display_mode *mode)
-{
-    unsigned int i, pre;
-    unsigned long mpclk, pllref, tmp;
-    unsigned int m = 1, n = 1, target_mbps = 1000;
-    unsigned int max_mbps = dptdin_map[ARRAY_SIZE(dptdin_map) - 1].max_mbps;
-    int bpp;
-
-    bpp = mipi_dsi_pixel_format_to_bpp(dsi->format);
-    if (bpp < 0) {
-        DRM_DEV_ERROR(dsi->dev,
-                  "failed to get bpp for pixel format %d\n",
-                  dsi->format);
-        return bpp;
-    }
-
-    mpclk = DIV_ROUND_UP(mode->clock, MSEC_PER_SEC);
-    if (mpclk) {
-        /* take 1 / 0.8, since mbps must big than bandwidth of RGB */
-        tmp = mpclk * (bpp / dsi->lanes) * 10 / 8;
-        if (tmp < max_mbps)
-            target_mbps = tmp;
-        else
-            DRM_DEV_ERROR(dsi->dev,
-                      "DPHY clock frequency is out of range\n");
-    }
-
-    pllref = DIV_ROUND_UP(clk_get_rate(dsi->pllref_clk), USEC_PER_SEC);
-    tmp = pllref;
-
-    /*
-     * The limits on the PLL divisor are:
-     *
-     *    5MHz <= (pllref / n) <= 40MHz
-     *
-     * we walk over these values in descreasing order so that if we hit
-     * an exact match for target_mbps it is more likely that "m" will be
-     * even.
-     *
-     * TODO: ensure that "m" is even after this loop.
-     */
-    for (i = pllref / 5; i > (pllref / 40); i--) {
-        pre = pllref / i;
-        if ((tmp > (target_mbps % pre)) && (target_mbps / pre < 512)) {
-            tmp = target_mbps % pre;
-            n = i;
-            m = target_mbps / pre;
-        }
-        if (tmp == 0)
-            break;
-    }
-
-    dsi->lane_mbps = pllref / n * m;
-    dsi->input_div = n;
-    dsi->feedback_div = m;
-
-    return 0;
-}
-
-static int dw_mipi_dsi_host_attach(struct mipi_dsi_host *host,
-                   struct mipi_dsi_device *device)
-{
-    struct dw_mipi_dsi *dsi = host_to_dsi(host);
-
-    if (device->lanes > dsi->pdata->max_data_lanes) {
-        DRM_DEV_ERROR(dsi->dev,
-                  "the number of data lanes(%u) is too many\n",
-                  device->lanes);
-        return -EINVAL;
-    }
-
-    dsi->lanes = device->lanes;
-    dsi->channel = device->channel;
-    dsi->format = device->format;
-    dsi->mode_flags = device->mode_flags;
-    dsi->panel = of_drm_find_panel(device->dev.of_node);
-    if (dsi->panel)
-        return drm_panel_attach(dsi->panel, &dsi->connector);
-
-    return -EINVAL;
-}
-
-static int dw_mipi_dsi_host_detach(struct mipi_dsi_host *host,
-                   struct mipi_dsi_device *device)
-{
-    struct dw_mipi_dsi *dsi = host_to_dsi(host);
-
-    drm_panel_detach(dsi->panel);
-
-    return 0;
-}
-
-static void dw_mipi_message_config(struct dw_mipi_dsi *dsi,
-                   const struct mipi_dsi_msg *msg)
-{
-    bool lpm = msg->flags & MIPI_DSI_MSG_USE_LPM;
-    u32 val = 0;
-
-    if (msg->flags & MIPI_DSI_MSG_REQ_ACK)
-        val |= EN_ACK_RQST;
-    if (lpm)
-        val |= CMD_MODE_ALL_LP;
-
-    dsi_write(dsi, DSI_LPCLK_CTRL, lpm ? 0 : PHY_TXREQUESTCLKHS);
-    dsi_write(dsi, DSI_CMD_MODE_CFG, val);
-}
-
-static int dw_mipi_dsi_gen_pkt_hdr_write(struct dw_mipi_dsi *dsi, u32 hdr_val)
-{
-    int ret;
-    u32 val, mask;
-
-    ret = readl_poll_timeout(dsi->base + DSI_CMD_PKT_STATUS,
-                 val, !(val & GEN_CMD_FULL), 1000,
-                 CMD_PKT_STATUS_TIMEOUT_US);
-    if (ret < 0) {
-        DRM_DEV_ERROR(dsi->dev,
-                  "failed to get available command FIFO\n");
-        return ret;
-    }
-
-    dsi_write(dsi, DSI_GEN_HDR, hdr_val);
-
-    mask = GEN_CMD_EMPTY | GEN_PLD_W_EMPTY;
-    ret = readl_poll_timeout(dsi->base + DSI_CMD_PKT_STATUS,
-                 val, (val & mask) == mask,
-                 1000, CMD_PKT_STATUS_TIMEOUT_US);
-    if (ret < 0) {
-        DRM_DEV_ERROR(dsi->dev, "failed to write command FIFO\n");
-        return ret;
-    }
-
-    return 0;
-}
-
-static int dw_mipi_dsi_dcs_short_write(struct dw_mipi_dsi *dsi,
-                       const struct mipi_dsi_msg *msg)
-{
-    const u8 *tx_buf = msg->tx_buf;
-    u16 data = 0;
-    u32 val;
-
-    if (msg->tx_len > 0)
-        data |= tx_buf[0];
-    if (msg->tx_len > 1)
-        data |= tx_buf[1] << 8;
-
-    if (msg->tx_len > 2) {
-        DRM_DEV_ERROR(dsi->dev,
-                  "too long tx buf length %zu for short write\n",
-                  msg->tx_len);
-        return -EINVAL;
-    }
-
-    val = GEN_HDATA(data) | GEN_HTYPE(msg->type);
-    return dw_mipi_dsi_gen_pkt_hdr_write(dsi, val);
-}
-
-static int dw_mipi_dsi_dcs_long_write(struct dw_mipi_dsi *dsi,
-                      const struct mipi_dsi_msg *msg)
-{
-    const u8 *tx_buf = msg->tx_buf;
-    int len = msg->tx_len, pld_data_bytes = sizeof(u32), ret;
-    u32 hdr_val = GEN_HDATA(msg->tx_len) | GEN_HTYPE(msg->type);
-    u32 remainder;
-    u32 val;
-
-    if (msg->tx_len < 3) {
-        DRM_DEV_ERROR(dsi->dev,
-                  "wrong tx buf length %zu for long write\n",
-                  msg->tx_len);
-        return -EINVAL;
-    }
-
-    while (DIV_ROUND_UP(len, pld_data_bytes)) {
-        if (len < pld_data_bytes) {
-            remainder = 0;
-            memcpy(&remainder, tx_buf, len);
-            dsi_write(dsi, DSI_GEN_PLD_DATA, remainder);
-            len = 0;
-        } else {
-            memcpy(&remainder, tx_buf, pld_data_bytes);
-            dsi_write(dsi, DSI_GEN_PLD_DATA, remainder);
-            tx_buf += pld_data_bytes;
-            len -= pld_data_bytes;
-        }
-
-        ret = readl_poll_timeout(dsi->base + DSI_CMD_PKT_STATUS,
-                     val, !(val & GEN_PLD_W_FULL), 1000,
-                     CMD_PKT_STATUS_TIMEOUT_US);
-        if (ret < 0) {
-            DRM_DEV_ERROR(dsi->dev,
-                      "failed to get available write payload FIFO\n");
-            return ret;
-        }
-    }
-
-    return dw_mipi_dsi_gen_pkt_hdr_write(dsi, hdr_val);
-}
-
-static ssize_t dw_mipi_dsi_host_transfer(struct mipi_dsi_host *host,
-                     const struct mipi_dsi_msg *msg)
-{
-    struct dw_mipi_dsi *dsi = host_to_dsi(host);
-    int ret;
-
-    dw_mipi_message_config(dsi, msg);
-
-    switch (msg->type) {
-    case MIPI_DSI_DCS_SHORT_WRITE:
-    case MIPI_DSI_DCS_SHORT_WRITE_PARAM:
-    case MIPI_DSI_SET_MAXIMUM_RETURN_PACKET_SIZE:
-        ret = dw_mipi_dsi_dcs_short_write(dsi, msg);
-        break;
-    case MIPI_DSI_DCS_LONG_WRITE:
-        ret = dw_mipi_dsi_dcs_long_write(dsi, msg);
-        break;
-    default:
-        DRM_DEV_ERROR(dsi->dev, "unsupported message type 0x%02x\n",
-                  msg->type);
-        ret = -EINVAL;
-    }
-
-    return ret;
-}
-
-static const struct mipi_dsi_host_ops dw_mipi_dsi_host_ops = {
-    .attach = dw_mipi_dsi_host_attach,
-    .detach = dw_mipi_dsi_host_detach,
-    .transfer = dw_mipi_dsi_host_transfer,
-};
-
-static void dw_mipi_dsi_video_mode_config(struct dw_mipi_dsi *dsi)
-{
-    u32 val;
-
-    val = ENABLE_LOW_POWER;
-
-    if (dsi->mode_flags & MIPI_DSI_MODE_VIDEO_BURST)
-        val |= VID_MODE_TYPE_BURST;
-    else if (dsi->mode_flags & MIPI_DSI_MODE_VIDEO_SYNC_PULSE)
-        val |= VID_MODE_TYPE_NON_BURST_SYNC_PULSES;
-    else
-        val |= VID_MODE_TYPE_NON_BURST_SYNC_EVENTS;
-
-    dsi_write(dsi, DSI_VID_MODE_CFG, val);
-}
-
-static void dw_mipi_dsi_set_mode(struct dw_mipi_dsi *dsi,
-                 enum dw_mipi_dsi_mode mode)
-{
-    if (mode == DW_MIPI_DSI_CMD_MODE) {
-        dsi_write(dsi, DSI_PWR_UP, RESET);
-        dsi_write(dsi, DSI_MODE_CFG, ENABLE_CMD_MODE);
-        dsi_write(dsi, DSI_PWR_UP, POWERUP);
-    } else {
-        dsi_write(dsi, DSI_PWR_UP, RESET);
-        dsi_write(dsi, DSI_MODE_CFG, ENABLE_VIDEO_MODE);
-        dw_mipi_dsi_video_mode_config(dsi);
-        dsi_write(dsi, DSI_LPCLK_CTRL, PHY_TXREQUESTCLKHS);
-        dsi_write(dsi, DSI_PWR_UP, POWERUP);
-    }
-}
-
-static void dw_mipi_dsi_disable(struct dw_mipi_dsi *dsi)
-{
-    dsi_write(dsi, DSI_PWR_UP, RESET);
-    dsi_write(dsi, DSI_PHY_RSTZ, PHY_RSTZ);
-}
-
-static void dw_mipi_dsi_init(struct dw_mipi_dsi *dsi)
-{
-    /*
-     * The maximum permitted escape clock is 20MHz and it is derived from
-     * lanebyteclk, which is running at "lane_mbps / 8".  Thus we want:
-     *
-     *     (lane_mbps >> 3) / esc_clk_division < 20
-     * which is:
-     *     (lane_mbps >> 3) / 20 > esc_clk_division
-     */
-    u32 esc_clk_division = (dsi->lane_mbps >> 3) / 20 + 1;
-
-    dsi_write(dsi, DSI_PWR_UP, RESET);
-    dsi_write(dsi, DSI_PHY_RSTZ, PHY_DISFORCEPLL | PHY_DISABLECLK
-          | PHY_RSTZ | PHY_SHUTDOWNZ);
-    dsi_write(dsi, DSI_CLKMGR_CFG, TO_CLK_DIVIDSION(10) |
-          TX_ESC_CLK_DIVIDSION(esc_clk_division));
-}
-
-static void dw_mipi_dsi_dpi_config(struct dw_mipi_dsi *dsi,
-                   struct drm_display_mode *mode)
-{
-    u32 val = 0, color = 0;
-
-    switch (dsi->format) {
-    case MIPI_DSI_FMT_RGB888:
-        color = DPI_COLOR_CODING_24BIT;
-        break;
-    case MIPI_DSI_FMT_RGB666:
-        color = DPI_COLOR_CODING_18BIT_2 | EN18_LOOSELY;
-        break;
-    case MIPI_DSI_FMT_RGB666_PACKED:
-        color = DPI_COLOR_CODING_18BIT_1;
-        break;
-    case MIPI_DSI_FMT_RGB565:
-        color = DPI_COLOR_CODING_16BIT_1;
-        break;
-    }
-
-    if (mode->flags & DRM_MODE_FLAG_NVSYNC)
-        val |= VSYNC_ACTIVE_LOW;
-    if (mode->flags & DRM_MODE_FLAG_NHSYNC)
-        val |= HSYNC_ACTIVE_LOW;
-
-    dsi_write(dsi, DSI_DPI_VCID, DPI_VID(dsi->channel));
-    dsi_write(dsi, DSI_DPI_COLOR_CODING, color);
-    dsi_write(dsi, DSI_DPI_CFG_POL, val);
-    dsi_write(dsi, DSI_DPI_LP_CMD_TIM, OUTVACT_LPCMD_TIME(4)
-          | INVACT_LPCMD_TIME(4));
-}
-
-static void dw_mipi_dsi_packet_handler_config(struct dw_mipi_dsi *dsi)
-{
-    dsi_write(dsi, DSI_PCKHDL_CFG, EN_CRC_RX | EN_ECC_RX | EN_BTA);
-}
-
-static void dw_mipi_dsi_video_packet_config(struct dw_mipi_dsi *dsi,
-                        struct drm_display_mode *mode)
-{
-    dsi_write(dsi, DSI_VID_PKT_SIZE, VID_PKT_SIZE(mode->hdisplay));
-}
-
-static void dw_mipi_dsi_command_mode_config(struct dw_mipi_dsi *dsi)
-{
-    dsi_write(dsi, DSI_TO_CNT_CFG, HSTX_TO_CNT(1000) | LPRX_TO_CNT(1000));
-    dsi_write(dsi, DSI_BTA_TO_CNT, 0xd00);
-    dsi_write(dsi, DSI_MODE_CFG, ENABLE_CMD_MODE);
-}
-
-/* Get lane byte clock cycles. */
-static u32 dw_mipi_dsi_get_hcomponent_lbcc(struct dw_mipi_dsi *dsi,
-                       struct drm_display_mode *mode,
-                       u32 hcomponent)
-{
-    u32 frac, lbcc;
-
-    lbcc = hcomponent * dsi->lane_mbps * MSEC_PER_SEC / 8;
-
-    frac = lbcc % mode->clock;
-    lbcc = lbcc / mode->clock;
-    if (frac)
-        lbcc++;
-
-    return lbcc;
-}
-
-static void dw_mipi_dsi_line_timer_config(struct dw_mipi_dsi *dsi,
-                      struct drm_display_mode *mode)
-{
-    u32 htotal, hsa, hbp, lbcc;
-
-    htotal = mode->htotal;
-    hsa = mode->hsync_end - mode->hsync_start;
-    hbp = mode->htotal - mode->hsync_end;
-
-    lbcc = dw_mipi_dsi_get_hcomponent_lbcc(dsi, mode, htotal);
-    dsi_write(dsi, DSI_VID_HLINE_TIME, lbcc);
-
-    lbcc = dw_mipi_dsi_get_hcomponent_lbcc(dsi, mode, hsa);
-    dsi_write(dsi, DSI_VID_HSA_TIME, lbcc);
-
-    lbcc = dw_mipi_dsi_get_hcomponent_lbcc(dsi, mode, hbp);
-    dsi_write(dsi, DSI_VID_HBP_TIME, lbcc);
-}
-
-static void dw_mipi_dsi_vertical_timing_config(struct dw_mipi_dsi *dsi,
-                           struct drm_display_mode *mode)
-{
-    u32 vactive, vsa, vfp, vbp;
-
-    vactive = mode->vdisplay;
-    vsa = mode->vsync_end - mode->vsync_start;
-    vfp = mode->vsync_start - mode->vdisplay;
-    vbp = mode->vtotal - mode->vsync_end;
-
-    dsi_write(dsi, DSI_VID_VACTIVE_LINES, vactive);
-    dsi_write(dsi, DSI_VID_VSA_LINES, vsa);
-    dsi_write(dsi, DSI_VID_VFP_LINES, vfp);
-    dsi_write(dsi, DSI_VID_VBP_LINES, vbp);
-}
-
-static void dw_mipi_dsi_dphy_timing_config(struct dw_mipi_dsi *dsi)
-{
-    dsi_write(dsi, DSI_PHY_TMR_CFG, PHY_HS2LP_TIME(0x40)
-          | PHY_LP2HS_TIME(0x40) | MAX_RD_TIME(10000));
-
-    dsi_write(dsi, DSI_PHY_TMR_LPCLK_CFG, PHY_CLKHS2LP_TIME(0x40)
-          | PHY_CLKLP2HS_TIME(0x40));
-}
-
-static void dw_mipi_dsi_dphy_interface_config(struct dw_mipi_dsi *dsi)
-{
-    dsi_write(dsi, DSI_PHY_IF_CFG, PHY_STOP_WAIT_TIME(0x20) |
-          N_LANES(dsi->lanes));
-}
-
-static void dw_mipi_dsi_clear_err(struct dw_mipi_dsi *dsi)
-{
-    dsi_read(dsi, DSI_INT_ST0);
-    dsi_read(dsi, DSI_INT_ST1);
-    dsi_write(dsi, DSI_INT_MSK0, 0);
-    dsi_write(dsi, DSI_INT_MSK1, 0);
-}
-
-static void dw_mipi_dsi_encoder_disable(struct drm_encoder *encoder)
-{
-    struct dw_mipi_dsi *dsi = encoder_to_dsi(encoder);
-
-    if (dsi->dpms_mode != DRM_MODE_DPMS_ON)
-        return;
-
-    if (clk_prepare_enable(dsi->pclk)) {
-        DRM_DEV_ERROR(dsi->dev, "Failed to enable pclk\n");
-        return;
-    }
-
-    drm_panel_disable(dsi->panel);
-
-    dw_mipi_dsi_set_mode(dsi, DW_MIPI_DSI_CMD_MODE);
-    drm_panel_unprepare(dsi->panel);
-
-    dw_mipi_dsi_disable(dsi);
-    pm_runtime_put(dsi->dev);
-    clk_disable_unprepare(dsi->pclk);
-    dsi->dpms_mode = DRM_MODE_DPMS_OFF;
-}
-
-static void dw_mipi_dsi_encoder_enable(struct drm_encoder *encoder)
-{
-    struct dw_mipi_dsi *dsi = encoder_to_dsi(encoder);
-    struct drm_display_mode *mode = &encoder->crtc->state->adjusted_mode;
-    const struct dw_mipi_dsi_plat_data *pdata = dsi->pdata;
-    int mux = drm_of_encoder_active_endpoint_id(dsi->dev->of_node, encoder);
-    u32 val;
-    int ret;
-
-    ret = dw_mipi_dsi_get_lane_bps(dsi, mode);
-    if (ret < 0)
-        return;
-
-    if (dsi->dpms_mode == DRM_MODE_DPMS_ON)
-        return;
-
-    if (clk_prepare_enable(dsi->pclk)) {
-        DRM_DEV_ERROR(dsi->dev, "Failed to enable pclk\n");
-        return;
-    }
-
-    pm_runtime_get_sync(dsi->dev);
-    dw_mipi_dsi_init(dsi);
-    dw_mipi_dsi_dpi_config(dsi, mode);
-    dw_mipi_dsi_packet_handler_config(dsi);
-    dw_mipi_dsi_video_mode_config(dsi);
-    dw_mipi_dsi_video_packet_config(dsi, mode);
-    dw_mipi_dsi_command_mode_config(dsi);
-    dw_mipi_dsi_line_timer_config(dsi, mode);
-    dw_mipi_dsi_vertical_timing_config(dsi, mode);
-    dw_mipi_dsi_dphy_timing_config(dsi);
-    dw_mipi_dsi_dphy_interface_config(dsi);
-    dw_mipi_dsi_clear_err(dsi);
-
-    /*
-     * For the RK3399, the clk of grf must be enabled before writing grf -     * register. And for RK3288 or other soc, this grf_clk must be NULL,
-     * the clk_prepare_enable return true directly.
-     */
-    ret = clk_prepare_enable(dsi->grf_clk);
-    if (ret) {
-        DRM_DEV_ERROR(dsi->dev, "Failed to enable grf_clk: %d\n", ret);
-        return;
-    }
-
-    if (pdata->grf_dsi0_mode_reg)
-        regmap_write(dsi->grf_regmap, pdata->grf_dsi0_mode_reg,
-                 pdata->grf_dsi0_mode);
-
-    dw_mipi_dsi_phy_init(dsi);
-    dw_mipi_dsi_wait_for_two_frames(mode);
-
-    dw_mipi_dsi_set_mode(dsi, DW_MIPI_DSI_CMD_MODE);
-    if (drm_panel_prepare(dsi->panel))
-        DRM_DEV_ERROR(dsi->dev, "failed to prepare panel\n");
-
-    dw_mipi_dsi_set_mode(dsi, DW_MIPI_DSI_VID_MODE);
-    drm_panel_enable(dsi->panel);
-
-    clk_disable_unprepare(dsi->pclk);
-
-    if (mux)
-        val = pdata->dsi0_en_bit | (pdata->dsi0_en_bit << 16);
-    else
-        val = pdata->dsi0_en_bit << 16;
-
-    regmap_write(dsi->grf_regmap, pdata->grf_switch_reg, val);
-    DRM_DEV_DEBUG(dsi->dev,
-              "vop %s output to dsi0\n", (mux) ? "LIT" : "BIG");
-    dsi->dpms_mode = DRM_MODE_DPMS_ON;
-
-    clk_disable_unprepare(dsi->grf_clk);
-}
-
-static int
-dw_mipi_dsi_encoder_atomic_check(struct drm_encoder *encoder,
-                 struct drm_crtc_state *crtc_state,
-                 struct drm_connector_state *conn_state)
-{
-    struct rockchip_crtc_state *s = to_rockchip_crtc_state(crtc_state);
-    struct dw_mipi_dsi *dsi = encoder_to_dsi(encoder);
-
-    switch (dsi->format) {
-    case MIPI_DSI_FMT_RGB888:
-        s->output_mode = ROCKCHIP_OUT_MODE_P888;
-        break;
-    case MIPI_DSI_FMT_RGB666:
-        s->output_mode = ROCKCHIP_OUT_MODE_P666;
-        break;
-    case MIPI_DSI_FMT_RGB565:
-        s->output_mode = ROCKCHIP_OUT_MODE_P565;
-        break;
-    default:
-        WARN_ON(1);
-        return -EINVAL;
-    }
-
-    s->output_type = DRM_MODE_CONNECTOR_DSI;
-
-    return 0;
-}
-
-static const struct drm_encoder_helper_funcs
-dw_mipi_dsi_encoder_helper_funcs = {
-    .enable = dw_mipi_dsi_encoder_enable,
-    .disable = dw_mipi_dsi_encoder_disable,
-    .atomic_check = dw_mipi_dsi_encoder_atomic_check,
-};
-
-static const struct drm_encoder_funcs dw_mipi_dsi_encoder_funcs = {
-    .destroy = drm_encoder_cleanup,
-};
-
-static int dw_mipi_dsi_connector_get_modes(struct drm_connector *connector)
-{
-    struct dw_mipi_dsi *dsi = con_to_dsi(connector);
-
-    return drm_panel_get_modes(dsi->panel);
-}
-
-static struct drm_connector_helper_funcs dw_mipi_dsi_connector_helper_funcs = {
-    .get_modes = dw_mipi_dsi_connector_get_modes,
-};
-
-static void dw_mipi_dsi_drm_connector_destroy(struct drm_connector *connector)
-{
-    drm_connector_unregister(connector);
-    drm_connector_cleanup(connector);
-}
-
-static const struct drm_connector_funcs dw_mipi_dsi_atomic_connector_funcs = {
-    .fill_modes = drm_helper_probe_single_connector_modes,
-    .destroy = dw_mipi_dsi_drm_connector_destroy,
-    .reset = drm_atomic_helper_connector_reset,
-    .atomic_duplicate_state = drm_atomic_helper_connector_duplicate_state,
-    .atomic_destroy_state = drm_atomic_helper_connector_destroy_state,
-};
-
-static int dw_mipi_dsi_register(struct drm_device *drm,
-                struct dw_mipi_dsi *dsi)
-{
-    struct drm_encoder *encoder = &dsi->encoder;
-    struct drm_connector *connector = &dsi->connector;
-    struct device *dev = dsi->dev;
-    int ret;
-
-    encoder->possible_crtcs = drm_of_find_possible_crtcs(drm,
-                                 dev->of_node);
-    /*
-     * If we failed to find the CRTC(s) which this encoder is
-     * supposed to be connected to, it's because the CRTC has
-     * not been registered yet.  Defer probing, and hope that
-     * the required CRTC is added later.
-     */
-    if (encoder->possible_crtcs == 0)
-        return -EPROBE_DEFER;
-
-    drm_encoder_helper_add(&dsi->encoder,
-                   &dw_mipi_dsi_encoder_helper_funcs);
-    ret = drm_encoder_init(drm, &dsi->encoder, &dw_mipi_dsi_encoder_funcs,
-                   DRM_MODE_ENCODER_DSI, NULL);
-    if (ret) {
-        DRM_DEV_ERROR(dev, "Failed to initialize encoder with drm\n");
-        return ret;
-    }
-
-    drm_connector_helper_add(connector,
-                 &dw_mipi_dsi_connector_helper_funcs);
-
-    drm_connector_init(drm, &dsi->connector,
-               &dw_mipi_dsi_atomic_connector_funcs,
-               DRM_MODE_CONNECTOR_DSI);
-
-    drm_mode_connector_attach_encoder(connector, encoder);
-
-    return 0;
-}
-
-static int rockchip_mipi_parse_dt(struct dw_mipi_dsi *dsi)
-{
-    struct device_node *np = dsi->dev->of_node;
-
-    dsi->grf_regmap = syscon_regmap_lookup_by_phandle(np, "rockchip,grf");
-    if (IS_ERR(dsi->grf_regmap)) {
-        DRM_DEV_ERROR(dsi->dev, "Unable to get rockchip,grf\n");
-        return PTR_ERR(dsi->grf_regmap);
-    }
-
-    return 0;
-}
-
-static struct dw_mipi_dsi_plat_data rk3288_mipi_dsi_drv_data = {
-    .dsi0_en_bit = RK3288_DSI0_SEL_VOP_LIT,
-    .dsi1_en_bit = RK3288_DSI1_SEL_VOP_LIT,
-    .grf_switch_reg = RK3288_GRF_SOC_CON6,
-    .max_data_lanes = 4,
-};
-
-static struct dw_mipi_dsi_plat_data rk3399_mipi_dsi_drv_data = {
-    .dsi0_en_bit = RK3399_DSI0_SEL_VOP_LIT,
-    .dsi1_en_bit = RK3399_DSI1_SEL_VOP_LIT,
-    .grf_switch_reg = RK3399_GRF_SOC_CON20,
-    .grf_dsi0_mode = RK3399_GRF_DSI_MODE,
-    .grf_dsi0_mode_reg = RK3399_GRF_SOC_CON22,
-    .flags = DW_MIPI_NEEDS_PHY_CFG_CLK | DW_MIPI_NEEDS_GRF_CLK,
-    .max_data_lanes = 4,
-};
-
-static const struct of_device_id dw_mipi_dsi_dt_ids[] = {
-    {
-     .compatible = "rockchip,rk3288-mipi-dsi",
-     .data = &rk3288_mipi_dsi_drv_data,
-    }, {
-     .compatible = "rockchip,rk3399-mipi-dsi",
-     .data = &rk3399_mipi_dsi_drv_data,
-    },
-    { /* sentinel */ }
-};
-MODULE_DEVICE_TABLE(of, dw_mipi_dsi_dt_ids);
-
-static int dw_mipi_dsi_bind(struct device *dev, struct device *master,
-                void *data)
-{
-    const struct of_device_id *of_id =
-            of_match_device(dw_mipi_dsi_dt_ids, dev);
-    const struct dw_mipi_dsi_plat_data *pdata = of_id->data;
-    struct platform_device *pdev = to_platform_device(dev);
-    struct reset_control *apb_rst;
-    struct drm_device *drm = data;
-    struct dw_mipi_dsi *dsi;
-    struct resource *res;
-    int ret;
-
-    dsi = devm_kzalloc(dev, sizeof(*dsi), GFP_KERNEL);
-    if (!dsi)
-        return -ENOMEM;
-
-    dsi->dev = dev;
-    dsi->pdata = pdata;
-    dsi->dpms_mode = DRM_MODE_DPMS_OFF;
-
-    ret = rockchip_mipi_parse_dt(dsi);
-    if (ret)
-        return ret;
-
-    res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
-    if (!res)
-        return -ENODEV;
-
-    dsi->base = devm_ioremap_resource(dev, res);
-    if (IS_ERR(dsi->base))
-        return PTR_ERR(dsi->base);
-
-    dsi->pllref_clk = devm_clk_get(dev, "ref");
-    if (IS_ERR(dsi->pllref_clk)) {
-        ret = PTR_ERR(dsi->pllref_clk);
-        DRM_DEV_ERROR(dev,
-                  "Unable to get pll reference clock: %d\n", ret);
-        return ret;
-    }
-
-    dsi->pclk = devm_clk_get(dev, "pclk");
-    if (IS_ERR(dsi->pclk)) {
-        ret = PTR_ERR(dsi->pclk);
-        DRM_DEV_ERROR(dev, "Unable to get pclk: %d\n", ret);
-        return ret;
-    }
-
-    /*
-     * Note that the reset was not defined in the initial device tree, so
-     * we have to be prepared for it not being found.
-     */
-    apb_rst = devm_reset_control_get(dev, "apb");
-    if (IS_ERR(apb_rst)) {
-        ret = PTR_ERR(apb_rst);
-        if (ret == -ENOENT) {
-            apb_rst = NULL;
-        } else {
-            DRM_DEV_ERROR(dev,
-                      "Unable to get reset control: %d\n", ret);
-            return ret;
-        }
-    }
-
-    if (apb_rst) {
-        ret = clk_prepare_enable(dsi->pclk);
-        if (ret) {
-            DRM_DEV_ERROR(dev, "Failed to enable pclk\n");
-            return ret;
-        }
-
-        reset_control_assert(apb_rst);
-        usleep_range(10, 20);
-        reset_control_deassert(apb_rst);
-
-        clk_disable_unprepare(dsi->pclk);
-    }
-
-    if (pdata->flags & DW_MIPI_NEEDS_PHY_CFG_CLK) {
-        dsi->phy_cfg_clk = devm_clk_get(dev, "phy_cfg");
-        if (IS_ERR(dsi->phy_cfg_clk)) {
-            ret = PTR_ERR(dsi->phy_cfg_clk);
-            DRM_DEV_ERROR(dev,
-                      "Unable to get phy_cfg_clk: %d\n", ret);
-            return ret;
-        }
-    }
-
-    if (pdata->flags & DW_MIPI_NEEDS_GRF_CLK) {
-        dsi->grf_clk = devm_clk_get(dev, "grf");
-        if (IS_ERR(dsi->grf_clk)) {
-            ret = PTR_ERR(dsi->grf_clk);
-            DRM_DEV_ERROR(dev, "Unable to get grf_clk: %d\n", ret);
-            return ret;
-        }
-    }
-
-    ret = clk_prepare_enable(dsi->pllref_clk);
-    if (ret) {
-        DRM_DEV_ERROR(dev, "Failed to enable pllref_clk\n");
-        return ret;
-    }
-
-    ret = dw_mipi_dsi_register(drm, dsi);
-    if (ret) {
-        DRM_DEV_ERROR(dev, "Failed to register mipi_dsi: %d\n", ret);
-        goto err_pllref;
-    }
-
-    pm_runtime_enable(dev);
-
-    dsi->dsi_host.ops = &dw_mipi_dsi_host_ops;
-    dsi->dsi_host.dev = dev;
-    ret = mipi_dsi_host_register(&dsi->dsi_host);
-    if (ret) {
-        DRM_DEV_ERROR(dev, "Failed to register MIPI host: %d\n", ret);
-        goto err_cleanup;
-    }
-
-    if (!dsi->panel) {
-        ret = -EPROBE_DEFER;
-        goto err_mipi_dsi_host;
-    }
-
-    dev_set_drvdata(dev, dsi);
-    return 0;
-
-err_mipi_dsi_host:
-    mipi_dsi_host_unregister(&dsi->dsi_host);
-err_cleanup:
-    drm_encoder_cleanup(&dsi->encoder);
-    drm_connector_cleanup(&dsi->connector);
-err_pllref:
-    clk_disable_unprepare(dsi->pllref_clk);
-    return ret;
-}
-
-static void dw_mipi_dsi_unbind(struct device *dev, struct device *master,
-                   void *data)
-{
-    struct dw_mipi_dsi *dsi = dev_get_drvdata(dev);
-
-    mipi_dsi_host_unregister(&dsi->dsi_host);
-    pm_runtime_disable(dev);
-    clk_disable_unprepare(dsi->pllref_clk);
-}
-
-static const struct component_ops dw_mipi_dsi_ops = {
-    .bind    = dw_mipi_dsi_bind,
-    .unbind    = dw_mipi_dsi_unbind,
-};
-
-static int dw_mipi_dsi_probe(struct platform_device *pdev)
-{
-    return component_add(&pdev->dev, &dw_mipi_dsi_ops);
-}
-
-static int dw_mipi_dsi_remove(struct platform_device *pdev)
-{
-    component_del(&pdev->dev, &dw_mipi_dsi_ops);
-    return 0;
-}
-
-struct platform_driver dw_mipi_dsi_driver = {
-    .probe        = dw_mipi_dsi_probe,
-    .remove        = dw_mipi_dsi_remove,
-    .driver        = {
-        .of_match_table = dw_mipi_dsi_dt_ids,
-        .name    = DRIVER_NAME,
-    },
-};
diff --git a/drivers/gpu/drm/rockchip/dw-mipi-dsi_rockchip.c b/drivers/gpu/drm/rockchip/dw-mipi-dsi_rockchip.c
new file mode 100644
index 0000000..c919d4f
--- /dev/null
+++ b/drivers/gpu/drm/rockchip/dw-mipi-dsi_rockchip.c
@@ -0,0 +1,756 @@
+/*
+ * Copyright (C) Fuzhou Rockchip Electronics Co.Ltd
+ * Author:
+ *      Chris Zhong <zyw@xxxxxxxxxxxxxx>
+ *      Nickey Yang <nickey.yang@xxxxxxxxxxxxxx>
+ *
+ * This software is licensed under the terms of the GNU General Public
+ * License version 2, as published by the Free Software Foundation, and
+ * may be copied, distributed, and modified under those terms.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.
+ *
+ * License terms:  GNU General Public License (GPL), version 2
+ */
+
+#include <linux/clk.h>
+#include <linux/iopoll.h>
+#include <linux/math64.h>
+#include <linux/module.h>
+#include <linux/of_device.h>
+#include <drm/drmP.h>
+#include <drm/drm_mipi_dsi.h>
+#include <drm/bridge/dw_mipi_dsi.h>
+#include <video/mipi_display.h>
+#include <linux/regmap.h>
+#include <drm/drm_of.h>
+#include <linux/mfd/syscon.h>
+
+#include "rockchip_drm_drv.h"
+#include "rockchip_drm_vop.h"
+
+#define DSI_PHY_TST_CTRL0        0xb4
+#define PHY_TESTCLK            BIT(1)
+#define PHY_UNTESTCLK            0
+#define PHY_TESTCLR            BIT(0)
+#define PHY_UNTESTCLR            0
+
+#define DSI_PHY_TST_CTRL1        0xb8
+#define PHY_TESTEN            BIT(16)
+#define PHY_UNTESTEN            0
+#define PHY_TESTDOUT(n)            (((n) & 0xff) << 8)
+#define PHY_TESTDIN(n)            (((n) & 0xff) << 0)
+
+#define BYPASS_VCO_RANGE    BIT(7)
+#define VCO_RANGE_CON_SEL(val)    (((val) & 0x7) << 3)
+#define VCO_IN_CAP_CON_DEFAULT    (0x0 << 1)
+#define VCO_IN_CAP_CON_LOW    (0x1 << 1)
+#define VCO_IN_CAP_CON_HIGH    (0x2 << 1)
+#define REF_BIAS_CUR_SEL    BIT(0)
+
+#define CP_CURRENT_3UA    0x1
+#define CP_CURRENT_4_5UA    0x2
+#define CP_CURRENT_7_5UA    0x6
+#define CP_CURRENT_6UA    0x9
+#define CP_CURRENT_12UA    0xb
+#define CP_CURRENT_SEL(val)    ((val) & 0xf)
+#define CP_PROGRAM_EN        BIT(7)
+
+#define LPF_RESISTORS_15_5KOHM    0x1
+#define LPF_RESISTORS_13KOHM    0x2
+#define LPF_RESISTORS_11_5KOHM    0x4
+#define LPF_RESISTORS_10_5KOHM    0x8
+#define LPF_RESISTORS_8KOHM    0x10
+#define LPF_PROGRAM_EN        BIT(6)
+#define LPF_RESISTORS_SEL(val)    ((val) & 0x3f)
+
+#define HSFREQRANGE_SEL(val)    (((val) & 0x3f) << 1)
+
+#define INPUT_DIVIDER(val)    (((val) - 1) & 0x7f)
+#define LOW_PROGRAM_EN        0
+#define HIGH_PROGRAM_EN        BIT(7)
+#define LOOP_DIV_LOW_SEL(val)    (((val) - 1) & 0x1f)
+#define LOOP_DIV_HIGH_SEL(val)    ((((val) - 1) >> 5) & 0xf)
+#define PLL_LOOP_DIV_EN        BIT(5)
+#define PLL_INPUT_DIV_EN    BIT(4)
+
+#define POWER_CONTROL        BIT(6)
+#define INTERNAL_REG_CURRENT    BIT(3)
+#define BIAS_BLOCK_ON        BIT(2)
+#define BANDGAP_ON        BIT(0)
+
+#define TER_RESISTOR_HIGH    BIT(7)
+#define    TER_RESISTOR_LOW    0
+#define LEVEL_SHIFTERS_ON    BIT(6)
+#define TER_CAL_DONE        BIT(5)
+#define SETRD_MAX        (0x7 << 2)
+#define POWER_MANAGE        BIT(1)
+#define TER_RESISTORS_ON    BIT(0)
+
+#define BIASEXTR_SEL(val)    ((val) & 0x7)
+#define BANDGAP_SEL(val)    ((val) & 0x7)
+#define TLP_PROGRAM_EN        BIT(7)
+#define THS_PRE_PROGRAM_EN    BIT(7)
+#define THS_ZERO_PROGRAM_EN    BIT(6)
+
+#define PLL_BIAS_CUR_SEL_CAP_VCO_CONTROL    0x10
+#define PLL_CP_CONTROL_PLL_LOCK_BYPASS    0x11
+#define PLL_LPF_AND_CP_CONTROL    0x12
+#define PLL_INPUT_DIVIDER_RATIO    0x17
+#define PLL_LOOP_DIVIDER_RATIO    0x18
+#define PLL_INPUT_AND_LOOP_DIVIDER_RATIOS_CONTROL    0x19
+#define BANDGAP_AND_BIAS_CONTROL    0x20
+#define TERMINATION_RESISTER_CONTROL    0x21
+#define AFE_BIAS_BANDGAP_ANALOG_PROGRAMMABILITY    0x22
+#define HS_RX_CONTROL_OF_LANE_0    0x44
+#define HS_TX_CLOCK_LANE_REQUEST_STATE_TIME_CONTROL    0x60
+#define HS_TX_CLOCK_LANE_PREPARE_STATE_TIME_CONTROL    0x61
+#define HS_TX_CLOCK_LANE_HS_ZERO_STATE_TIME_CONTROL    0x62
+#define HS_TX_CLOCK_LANE_TRAIL_STATE_TIME_CONTROL    0x63
+#define HS_TX_CLOCK_LANE_EXIT_STATE_TIME_CONTROL    0x64
+#define HS_TX_CLOCK_LANE_POST_TIME_CONTROL    0x65
+#define HS_TX_DATA_LANE_REQUEST_STATE_TIME_CONTROL    0x70
+#define HS_TX_DATA_LANE_PREPARE_STATE_TIME_CONTROL    0x71
+#define HS_TX_DATA_LANE_HS_ZERO_STATE_TIME_CONTROL    0x72
+#define HS_TX_DATA_LANE_TRAIL_STATE_TIME_CONTROL    0x73
+#define HS_TX_DATA_LANE_EXIT_STATE_TIME_CONTROL    0x74
+
+#define DW_MIPI_NEEDS_PHY_CFG_CLK    BIT(0)
+#define DW_MIPI_NEEDS_GRF_CLK        BIT(1)
+
+#define RK3288_GRF_SOC_CON6        0x025c
+#define RK3288_DSI0_SEL_VOP_LIT        BIT(6)
+#define RK3288_DSI1_SEL_VOP_LIT        BIT(9)
+
+#define RK3399_GRF_SOC_CON20        0x6250
+#define RK3399_DSI0_SEL_VOP_LIT        BIT(0)
+#define RK3399_DSI1_SEL_VOP_LIT        BIT(4)
+
+/* disable turnrequest, turndisable, forcetxstopmode, forcerxmode */
+#define RK3399_GRF_SOC_CON22        0x6258
+#define RK3399_GRF_DSI_MODE        0xffff0000
+
+#define to_dsi(nm)    container_of(nm, struct dw_mipi_dsi_rockchip, nm)
+
+enum {
+    BANDGAP_97_07,
+    BANDGAP_98_05,
+    BANDGAP_99_02,
+    BANDGAP_100_00,
+    BANDGAP_93_17,
+    BANDGAP_94_15,
+    BANDGAP_95_12,
+    BANDGAP_96_10,
+};
+
+enum {
+    BIASEXTR_87_1,
+    BIASEXTR_91_5,
+    BIASEXTR_95_9,
+    BIASEXTR_100,
+    BIASEXTR_105_94,
+    BIASEXTR_111_88,
+    BIASEXTR_118_8,
+    BIASEXTR_127_7,
+};
+
+struct rockchip_dw_dsi_chip_data {
+    u32 dsi0_en_bit;
+    u32 dsi1_en_bit;
+    u32 grf_switch_reg;
+    u32 grf_dsi0_mode;
+    u32 grf_dsi0_mode_reg;
+    unsigned int flags;
+    unsigned int max_data_lanes;
+};
+
+struct dw_mipi_dsi_rockchip {
+    struct device *dev;
+    struct drm_encoder encoder;
+    void __iomem *base;
+
+    struct regmap *grf_regmap;
+    struct clk *pllref_clk;
+    struct clk *grf_clk;
+    struct clk *phy_cfg_clk;
+
+    unsigned int lane_mbps; /* per lane */
+    u16 input_div;
+    u16 feedback_div;
+    u32 format;
+
+    const struct rockchip_dw_dsi_chip_data *cdata;
+    struct dw_mipi_dsi_plat_data pdata;
+};
+
+struct dphy_pll_parameter_map {
+    unsigned int max_mbps;
+    u8 hsfreqrange;
+    u8 icpctrl;
+    u8 lpfctrl;
+};
+
+/* The table is based on 27MHz DPHY pll reference clock. */
+static const struct dphy_pll_parameter_map dppa_map[] = {
+    {  89, 0x00, CP_CURRENT_3UA, LPF_RESISTORS_13KOHM},
+    {  99, 0x10, CP_CURRENT_3UA, LPF_RESISTORS_13KOHM},
+    { 109, 0x20, CP_CURRENT_3UA, LPF_RESISTORS_13KOHM},
+    { 129, 0x01, CP_CURRENT_3UA, LPF_RESISTORS_15_5KOHM},
+    { 139, 0x11, CP_CURRENT_3UA, LPF_RESISTORS_15_5KOHM},
+    { 149, 0x21, CP_CURRENT_3UA, LPF_RESISTORS_15_5KOHM},
+    { 169, 0x02, CP_CURRENT_6UA, LPF_RESISTORS_13KOHM},
+    { 179, 0x12, CP_CURRENT_6UA, LPF_RESISTORS_13KOHM},
+    { 199, 0x22, CP_CURRENT_6UA, LPF_RESISTORS_13KOHM},
+    { 219, 0x03, CP_CURRENT_4_5UA, LPF_RESISTORS_13KOHM},
+    { 239, 0x13, CP_CURRENT_4_5UA, LPF_RESISTORS_13KOHM},
+    { 249, 0x23, CP_CURRENT_4_5UA, LPF_RESISTORS_13KOHM},
+    { 269, 0x04, CP_CURRENT_6UA, LPF_RESISTORS_11_5KOHM},
+    { 299, 0x14, CP_CURRENT_6UA, LPF_RESISTORS_11_5KOHM},
+    { 329, 0x05, CP_CURRENT_3UA, LPF_RESISTORS_15_5KOHM},
+    { 359, 0x15, CP_CURRENT_3UA, LPF_RESISTORS_15_5KOHM},
+    { 399, 0x25, CP_CURRENT_3UA, LPF_RESISTORS_15_5KOHM},
+    { 449, 0x06, CP_CURRENT_7_5UA, LPF_RESISTORS_11_5KOHM},
+    { 499, 0x16, CP_CURRENT_7_5UA, LPF_RESISTORS_11_5KOHM},
+    { 549, 0x07, CP_CURRENT_7_5UA, LPF_RESISTORS_10_5KOHM},
+    { 599, 0x17, CP_CURRENT_7_5UA, LPF_RESISTORS_10_5KOHM},
+    { 649, 0x08, CP_CURRENT_7_5UA, LPF_RESISTORS_11_5KOHM},
+    { 699, 0x18, CP_CURRENT_7_5UA, LPF_RESISTORS_11_5KOHM},
+    { 749, 0x09, CP_CURRENT_7_5UA, LPF_RESISTORS_11_5KOHM},
+    { 799, 0x19, CP_CURRENT_7_5UA, LPF_RESISTORS_11_5KOHM},
+    { 849, 0x29, CP_CURRENT_7_5UA, LPF_RESISTORS_11_5KOHM},
+    { 899, 0x39, CP_CURRENT_7_5UA, LPF_RESISTORS_11_5KOHM},
+    { 949, 0x0a, CP_CURRENT_12UA, LPF_RESISTORS_8KOHM},
+    { 999, 0x1a, CP_CURRENT_12UA, LPF_RESISTORS_8KOHM},
+    {1049, 0x2a, CP_CURRENT_12UA, LPF_RESISTORS_8KOHM},
+    {1099, 0x3a, CP_CURRENT_12UA, LPF_RESISTORS_8KOHM},
+    {1149, 0x0b, CP_CURRENT_12UA, LPF_RESISTORS_10_5KOHM},
+    {1199, 0x1b, CP_CURRENT_12UA, LPF_RESISTORS_10_5KOHM},
+    {1249, 0x2b, CP_CURRENT_12UA, LPF_RESISTORS_10_5KOHM},
+    {1299, 0x3b, CP_CURRENT_12UA, LPF_RESISTORS_10_5KOHM},
+    {1349, 0x0c, CP_CURRENT_12UA, LPF_RESISTORS_10_5KOHM},
+    {1399, 0x1c, CP_CURRENT_12UA, LPF_RESISTORS_10_5KOHM},
+    {1449, 0x2c, CP_CURRENT_12UA, LPF_RESISTORS_10_5KOHM},
+    {1500, 0x3c, CP_CURRENT_12UA, LPF_RESISTORS_10_5KOHM}

minor nit: you should leave a space before the closing brace '}'.

+};
+
+static int max_mbps_to_parameter(unsigned int max_mbps)
+{
+    int i;
+
+    for (i = 0; i < ARRAY_SIZE(dppa_map); i++)
+        if (dppa_map[i].max_mbps >= max_mbps)
+            return i;
+
+    return -EINVAL;
+}
+
+static inline void dsi_write(struct dw_mipi_dsi_rockchip *dsi, u32 reg, u32 val)
+{
+    writel(val, dsi->base + reg);
+}
+
+static inline u32 dsi_read(struct dw_mipi_dsi_rockchip *dsi, u32 reg)
+{
+    return readl(dsi->base + reg);
+}
+
+static inline void dsi_set(struct dw_mipi_dsi_rockchip *dsi, u32 reg, u32 mask)
+{
+    dsi_write(dsi, reg, dsi_read(dsi, reg) | mask);
+}
+
+static inline void dsi_update_bits(struct dw_mipi_dsi_rockchip *dsi, u32 reg,
+                   u32 mask, u32 val)
+{
+    dsi_write(dsi, reg, (dsi_read(dsi, reg) & ~mask) | val);
+}
+
+static void dw_mipi_dsi_phy_write(struct dw_mipi_dsi_rockchip *dsi,
+                  u8 test_code,
+                  u8 test_data)
+{
+    /*
+     * With the falling edge on TESTCLK, the TESTDIN[7:0] signal content
+     * is latched internally as the current test code. Test data is
+     * programmed internally by rising edge on TESTCLK.
+     */
+    dsi_write(dsi, DSI_PHY_TST_CTRL0, PHY_TESTCLK | PHY_UNTESTCLR);
+
+    dsi_write(dsi, DSI_PHY_TST_CTRL1, PHY_TESTEN | PHY_TESTDOUT(0) |
+                      PHY_TESTDIN(test_code));
+
+    dsi_write(dsi, DSI_PHY_TST_CTRL0, PHY_UNTESTCLK | PHY_UNTESTCLR);
+
+    dsi_write(dsi, DSI_PHY_TST_CTRL1, PHY_UNTESTEN | PHY_TESTDOUT(0) |
+                      PHY_TESTDIN(test_data));
+
+    dsi_write(dsi, DSI_PHY_TST_CTRL0, PHY_TESTCLK | PHY_UNTESTCLR);
+}
+
+/**
+ * ns2bc - Nanoseconds to byte clock cycles
+ */
+static inline unsigned int ns2bc(struct dw_mipi_dsi_rockchip *dsi, int ns)
+{
+    return DIV_ROUND_UP(ns * dsi->lane_mbps / 8, 1000);
+}
+
+/**
+ * ns2ui - Nanoseconds to UI time periods
+ */
+static inline unsigned int ns2ui(struct dw_mipi_dsi_rockchip *dsi, int ns)
+{
+    return DIV_ROUND_UP(ns * dsi->lane_mbps, 1000);
+}
+
+static int dw_mipi_dsi_phy_init(void *priv_data)
+{
+    struct dw_mipi_dsi_rockchip *dsi = priv_data;
+    int ret, i, vco;
+
+    vco = (dsi->lane_mbps < 200) ? 0 : (dsi->lane_mbps + 100) / 200;
+
+    i = max_mbps_to_parameter(dsi->lane_mbps);
+    if (i < 0) {
+        DRM_DEV_ERROR(dsi->dev,
+                  "failed to get parameter for %dmbps clock\n",
+                  dsi->lane_mbps);
+        return i;
+    }
+
+    ret = clk_prepare_enable(dsi->phy_cfg_clk);
+    if (ret) {
+        DRM_DEV_ERROR(dsi->dev, "Failed to enable phy_cfg_clk\n");
+        return ret;
+    }
+
+    dw_mipi_dsi_phy_write(dsi, PLL_BIAS_CUR_SEL_CAP_VCO_CONTROL,
+                  BYPASS_VCO_RANGE |
+                  VCO_RANGE_CON_SEL(vco) |
+                  VCO_IN_CAP_CON_LOW |
+                  REF_BIAS_CUR_SEL);
+
+    dw_mipi_dsi_phy_write(dsi, PLL_CP_CONTROL_PLL_LOCK_BYPASS,
+                  CP_CURRENT_SEL(dppa_map[i].icpctrl));
+    dw_mipi_dsi_phy_write(dsi, PLL_LPF_AND_CP_CONTROL,
+                  CP_PROGRAM_EN | LPF_PROGRAM_EN |
+                  LPF_RESISTORS_SEL(dppa_map[i].lpfctrl));
+
+    dw_mipi_dsi_phy_write(dsi, HS_RX_CONTROL_OF_LANE_0,
+                  HSFREQRANGE_SEL(dppa_map[i].hsfreqrange));
+
+    dw_mipi_dsi_phy_write(dsi, PLL_INPUT_DIVIDER_RATIO,
+                  INPUT_DIVIDER(dsi->input_div));
+    dw_mipi_dsi_phy_write(dsi, PLL_LOOP_DIVIDER_RATIO,
+                  LOOP_DIV_LOW_SEL(dsi->feedback_div) |
+                  LOW_PROGRAM_EN);
+    /*
+     * We need set PLL_INPUT_AND_LOOP_DIVIDER_RATIOS_CONTROL immediately
+     * to make the configured LSB effective according to IP simulation
+     * and lab test results.
+     * Only in this way can we get correct mipi phy pll frequency.
+     */
+    dw_mipi_dsi_phy_write(dsi, PLL_INPUT_AND_LOOP_DIVIDER_RATIOS_CONTROL,
+                  PLL_LOOP_DIV_EN | PLL_INPUT_DIV_EN);
+    dw_mipi_dsi_phy_write(dsi, PLL_LOOP_DIVIDER_RATIO,
+                  LOOP_DIV_HIGH_SEL(dsi->feedback_div) |
+                  HIGH_PROGRAM_EN);
+    dw_mipi_dsi_phy_write(dsi, PLL_INPUT_AND_LOOP_DIVIDER_RATIOS_CONTROL,
+                  PLL_LOOP_DIV_EN | PLL_INPUT_DIV_EN);
+
+    dw_mipi_dsi_phy_write(dsi, AFE_BIAS_BANDGAP_ANALOG_PROGRAMMABILITY,
+                  LOW_PROGRAM_EN | BIASEXTR_SEL(BIASEXTR_127_7));
+    dw_mipi_dsi_phy_write(dsi, AFE_BIAS_BANDGAP_ANALOG_PROGRAMMABILITY,
+                  HIGH_PROGRAM_EN | BANDGAP_SEL(BANDGAP_96_10));
+
+    dw_mipi_dsi_phy_write(dsi, BANDGAP_AND_BIAS_CONTROL,
+                  POWER_CONTROL | INTERNAL_REG_CURRENT |
+                  BIAS_BLOCK_ON | BANDGAP_ON);
+
+    dw_mipi_dsi_phy_write(dsi, TERMINATION_RESISTER_CONTROL,
+                  TER_RESISTOR_LOW | TER_CAL_DONE |
+                  SETRD_MAX | TER_RESISTORS_ON);
+    dw_mipi_dsi_phy_write(dsi, TERMINATION_RESISTER_CONTROL,
+                  TER_RESISTOR_HIGH | LEVEL_SHIFTERS_ON |
+                  SETRD_MAX | POWER_MANAGE |
+                  TER_RESISTORS_ON);
+
+    dw_mipi_dsi_phy_write(dsi, HS_TX_CLOCK_LANE_REQUEST_STATE_TIME_CONTROL,
+                  TLP_PROGRAM_EN | ns2bc(dsi, 500));
+    dw_mipi_dsi_phy_write(dsi, HS_TX_CLOCK_LANE_PREPARE_STATE_TIME_CONTROL,
+                  THS_PRE_PROGRAM_EN | ns2ui(dsi, 40));
+    dw_mipi_dsi_phy_write(dsi, HS_TX_CLOCK_LANE_HS_ZERO_STATE_TIME_CONTROL,
+                  THS_ZERO_PROGRAM_EN | ns2bc(dsi, 300));
+    dw_mipi_dsi_phy_write(dsi, HS_TX_CLOCK_LANE_TRAIL_STATE_TIME_CONTROL,
+                  THS_PRE_PROGRAM_EN | ns2ui(dsi, 100));
+    dw_mipi_dsi_phy_write(dsi, HS_TX_CLOCK_LANE_EXIT_STATE_TIME_CONTROL,
+                  BIT(5) | ns2bc(dsi, 100));
+    dw_mipi_dsi_phy_write(dsi, HS_TX_CLOCK_LANE_POST_TIME_CONTROL,
+                  BIT(5) | (ns2bc(dsi, 60) + 7));
+
+    dw_mipi_dsi_phy_write(dsi, HS_TX_DATA_LANE_REQUEST_STATE_TIME_CONTROL,
+                  TLP_PROGRAM_EN | ns2bc(dsi, 500));
+    dw_mipi_dsi_phy_write(dsi, HS_TX_DATA_LANE_PREPARE_STATE_TIME_CONTROL,
+                  THS_PRE_PROGRAM_EN | (ns2ui(dsi, 50) + 20));
+    dw_mipi_dsi_phy_write(dsi, HS_TX_DATA_LANE_HS_ZERO_STATE_TIME_CONTROL,
+                  THS_ZERO_PROGRAM_EN | (ns2bc(dsi, 140) + 2));
+    dw_mipi_dsi_phy_write(dsi, HS_TX_DATA_LANE_TRAIL_STATE_TIME_CONTROL,
+                  THS_PRE_PROGRAM_EN | (ns2ui(dsi, 60) + 8));
+    dw_mipi_dsi_phy_write(dsi, HS_TX_DATA_LANE_EXIT_STATE_TIME_CONTROL,
+                  BIT(5) | ns2bc(dsi, 100));
+
+    clk_disable_unprepare(dsi->phy_cfg_clk);
+
+    return ret;
+}
+
+static int
+dw_mipi_dsi_get_lane_mbps(void *priv_data, struct drm_display_mode *mode,
+              unsigned long mode_flags, u32 lanes, u32 format,
+              unsigned int *lane_mbps)
+{
+    struct dw_mipi_dsi_rockchip *dsi = priv_data;
+    int bpp;
+    unsigned long mpclk, tmp;
+    unsigned int target_mbps = 1000;
+    unsigned int max_mbps = dppa_map[ARRAY_SIZE(dppa_map) - 1].max_mbps;
+    unsigned long best_freq = 0;
+    unsigned long fvco_min, fvco_max, fin, fout;
+    unsigned int min_prediv, max_prediv;
+    unsigned int _prediv, uninitialized_var(best_prediv);
+    unsigned long _fbdiv, uninitialized_var(best_fbdiv);
+    unsigned long min_delta = ULONG_MAX;
+
+    dsi->format = format;
+    bpp = mipi_dsi_pixel_format_to_bpp(dsi->format);
+    if (bpp < 0) {
+        DRM_DEV_ERROR(dsi->dev,
+                  "failed to get bpp for pixel format %d\n",
+                  dsi->format);
+        return bpp;
+    }
+
+    mpclk = DIV_ROUND_UP(mode->clock, MSEC_PER_SEC);
+    if (mpclk) {
+        /* take 1 / 0.8, since mbps must big than bandwidth of RGB */
+        tmp = mpclk * (bpp / lanes) * 10 / 8;
+        if (tmp < max_mbps)
+            target_mbps = tmp;
+        else
+            DRM_DEV_ERROR(dsi->dev,
+                      "DPHY clock frequency is out of range\n");
+    }
+
+    fin = clk_get_rate(dsi->pllref_clk);
+    fout = target_mbps * USEC_PER_SEC;
+
+    /* constraint: 5Mhz <= Fref / N <= 40MHz */
+    min_prediv = DIV_ROUND_UP(fin, 40 * USEC_PER_SEC);
+    max_prediv = fin / (5 * USEC_PER_SEC);
+
+    /* constraint: 80MHz <= Fvco <= 1500Mhz */
+    fvco_min = 80 * USEC_PER_SEC;
+    fvco_max = 1500 * USEC_PER_SEC;
+
+    for (_prediv = min_prediv; _prediv <= max_prediv; _prediv++) {
+        u64 tmp;
+        u32 delta;
+        /* Fvco = Fref * M / N */
+        tmp = (u64)fout * _prediv;
+        do_div(tmp, fin);
+        _fbdiv = tmp;
+        /*
+         * Due to the use of a "by 2 pre-scaler," the range of the
+         * feedback multiplication value M is limited to even division
+         * numbers, and m must be greater than 6, less than 512.
+         */
+        if (_fbdiv < 6 || _fbdiv > 512)
+            continue;
+
+        _fbdiv += _fbdiv % 2;
+
+        tmp = (u64)_fbdiv * fin;
+        do_div(tmp, _prediv);
+        if (tmp < fvco_min || tmp > fvco_max)
+            continue;
+
+        delta = abs(fout - tmp);
+        if (delta < min_delta) {
+            best_prediv = _prediv;
+            best_fbdiv = _fbdiv;
+            min_delta = delta;
+            best_freq = tmp;
+        }
+    }
+
+    if (best_freq) {
+        dsi->lane_mbps = DIV_ROUND_UP(best_freq, USEC_PER_SEC);
+        *lane_mbps = dsi->lane_mbps;
+        dsi->input_div = best_prediv;
+        dsi->feedback_div = best_fbdiv;
+    } else {
+        DRM_DEV_ERROR(dsi->dev, "Can not find best_freq for DPHY\n");
+    }
+
+    return 0;
+}
+
+static const struct dw_mipi_dsi_phy_ops dw_mipi_dsi_rockchip_phy_ops = {
+    .init = dw_mipi_dsi_phy_init,
+    .get_lane_mbps = dw_mipi_dsi_get_lane_mbps,
+};
+
+static struct rockchip_dw_dsi_chip_data rk3288_chip_data = {
+    .dsi0_en_bit = RK3288_DSI0_SEL_VOP_LIT,
+    .dsi1_en_bit = RK3288_DSI1_SEL_VOP_LIT,
+    .grf_switch_reg = RK3288_GRF_SOC_CON6,
+    .max_data_lanes = 4,
+};
+
+static struct rockchip_dw_dsi_chip_data rk3399_chip_data = {
+    .dsi0_en_bit = RK3399_DSI0_SEL_VOP_LIT,
+    .dsi1_en_bit = RK3399_DSI1_SEL_VOP_LIT,
+    .grf_switch_reg = RK3399_GRF_SOC_CON20,
+    .grf_dsi0_mode = RK3399_GRF_DSI_MODE,
+    .grf_dsi0_mode_reg = RK3399_GRF_SOC_CON22,
+    .flags = DW_MIPI_NEEDS_PHY_CFG_CLK | DW_MIPI_NEEDS_GRF_CLK,
+    .max_data_lanes = 4,
+};
+
+static const struct of_device_id dw_mipi_dsi_rockchip_dt_ids[] = {
+    {
+     .compatible = "rockchip,rk3288-mipi-dsi",
+     .data = &rk3288_chip_data,
+    }, {
+     .compatible = "rockchip,rk3399-mipi-dsi",
+     .data = &rk3399_chip_data,
+    },
+    { /* sentinel */ }
+};
+MODULE_DEVICE_TABLE(of, dw_mipi_dsi_rockchip_dt_ids);

It would be nice to have the above 3 structs at the bottom of the file
along with the dw_mipi_dsi_rockchip_driver struct creation. Using
of_device_get_match_data() should avoid the need to keep the of_device_id
table at the bottom.
Done in patch v3

+
+static void dw_mipi_dsi_encoder_mode_set(struct drm_encoder *encoder,
+                         struct drm_display_mode *mode,
+                         struct drm_display_mode *adjusted)
+{
+    struct dw_mipi_dsi_rockchip *dsi = to_dsi(encoder);
+    const struct rockchip_dw_dsi_chip_data *cdata = dsi->cdata;
+    int val, ret;
+
+    ret = drm_of_encoder_active_endpoint_id(dsi->dev->of_node,
+                        &dsi->encoder);
+    if (ret < 0)
+        return;
+    /*
+     * For the RK3399, the clk of grf must be enabled before writing grf +     * register. And for RK3288 or other soc, this grf_clk must be NULL,
+     * the clk_prepare_enable return true directly.
+     */
+    ret = clk_prepare_enable(dsi->grf_clk);
+    if (ret) {
+        DRM_DEV_ERROR(dsi->dev, "Failed to enable grf_clk: %d\n", ret);
+        return;
+    }
+
+    val = cdata->dsi0_en_bit << 16;
+    if (ret)
+        val |= cdata->dsi0_en_bit;

Is this "if (ret)" check okay here? The older code checked on a "mux"
variable.

+    regmap_write(dsi->grf_regmap, cdata->grf_switch_reg, val);
+
+    if (cdata->grf_dsi0_mode_reg)
+        regmap_write(dsi->grf_regmap, cdata->grf_dsi0_mode_reg,
+                 cdata->grf_dsi0_mode);
+
+    clk_disable_unprepare(dsi->grf_clk);
+}
+
+static int
+dw_mipi_dsi_encoder_atomic_check(struct drm_encoder *encoder,
+                 struct drm_crtc_state *crtc_state,
+                 struct drm_connector_state *conn_state)
+{
+    struct rockchip_crtc_state *s = to_rockchip_crtc_state(crtc_state);
+    struct dw_mipi_dsi_rockchip *dsi = to_dsi(encoder);
+
+    switch (dsi->format) {
+    case MIPI_DSI_FMT_RGB888:
+        s->output_mode = ROCKCHIP_OUT_MODE_P888;
+        break;
+    case MIPI_DSI_FMT_RGB666:
+        s->output_mode = ROCKCHIP_OUT_MODE_P666;
+        break;
+    case MIPI_DSI_FMT_RGB565:
+        s->output_mode = ROCKCHIP_OUT_MODE_P565;
+        break;
+    default:
+        WARN_ON(1);
+        return -EINVAL;
+    }
+
+    s->output_type = DRM_MODE_CONNECTOR_DSI;
+
+    return 0;
+}
+
+static const struct drm_encoder_helper_funcs
+dw_mipi_dsi_encoder_helper_funcs = {
+    .mode_set = dw_mipi_dsi_encoder_mode_set,

Are we using the mode_set() encoder helper func (instead of enable/disable) here because the dw-mipi-dsi bridge driver also does the majority of the DW DSI controller configuration
in the bridge's mode_set() helper?
yes, GRF should be set before bridge's mode_set().

+    .atomic_check = dw_mipi_dsi_encoder_atomic_check,
+};
+
+static const struct drm_encoder_funcs dw_mipi_dsi_encoder_funcs = {
+    .destroy = drm_encoder_cleanup,
+};
+
+static int rockchip_dsi_drm_create_encoder(struct dw_mipi_dsi_rockchip *dsi,
+                       struct drm_device *drm_dev)
+{
+    struct drm_encoder *encoder = &dsi->encoder;
+    int ret;
+
+    encoder->possible_crtcs = drm_of_find_possible_crtcs(drm_dev,
+                                 dsi->dev->of_node);
+
+    ret = drm_encoder_init(drm_dev, encoder, &dw_mipi_dsi_encoder_funcs,
+                   DRM_MODE_ENCODER_DSI, NULL);
+    if (ret) {
+        DRM_ERROR("Failed to initialize encoder with drm\n");
+        return ret;
+    }
+
+    drm_encoder_helper_add(encoder, &dw_mipi_dsi_encoder_helper_funcs);
+
+    return 0;
+}
+
+static int dw_mipi_dsi_rockchip_bind(struct device *dev,
+                     struct device *master,
+                     void *data)
+{
+    const struct of_device_id *of_id =
+            of_match_device(dw_mipi_dsi_rockchip_dt_ids, dev);
+    const struct rockchip_dw_dsi_chip_data *cdata = of_id->data;

You could use of_device_get_match_data() here.

+    struct dw_mipi_dsi_rockchip *dsi = dev_get_drvdata(dev);

I guess this needs to be fixed as Brian described in the other mail.

Thanks,
Archit



_______________________________________________
dri-devel mailing list
dri-devel@xxxxxxxxxxxxxxxxxxxxx
https://lists.freedesktop.org/mailman/listinfo/dri-devel





[Index of Archives]     [Linux DRI Users]     [Linux Intel Graphics]     [Linux USB Devel]     [Video for Linux]     [Linux Audio Users]     [Yosemite News]     [Linux Kernel]     [Linux SCSI]     [XFree86]     [Linux USB Devel]     [Video for Linux]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [XFree86]
  Powered by Linux