[PATCH v2 5/7] drm/sun4i: backend: Offset layer buffer address by DRAM starting address

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



The display backend, as well as other peripherals that have a DRAM
clock gate and access DRAM directly, bypassing the system bus,
address the DRAM starting from 0x0, while physical addresses the
system uses starts from 0x40000000 (or 0x20000000 in A80's case).

This issue was witnessed on the Cubietruck, which has 2GB of RAM.

Devices with less RAM function normally due to the DRAM address
wrapping around. CMA seems to always allocate its buffer at a
very high address, close to the end of DRAM.

On a 1GB RAM device, the physical address would be something like
0x78000000. The DRAM address 0x78000000 would access the same DRAM
region as 0x38000000 on a system, as the DRAM address would only
span 0x0 ~ 0x3fffffff. The bit 0x40000000 is non-functional in this
case.

However on the Cubietruck, the DRAM is 2GB. The physical address
is 0x40000000 ~ 0xbfffffff. The buffer would be something like
0xb8000000. But the DRAM address span 0x0 ~ 0x7fffffff, meaning
the buffer address wraps around to 0x38000000, which is wrong.
The correct DRAM address for it should be 0x78000000.

Correct the address configured into the backend layer registers
by PHYS_OFFSET to account for this.

Fixes: 9026e0d122ac ("drm: Add Allwinner A10 Display Engine support")
Signed-off-by: Chen-Yu Tsai <wens@xxxxxxxx>
---
 drivers/gpu/drm/sun4i/sun4i_backend.c | 7 +++++++
 1 file changed, 7 insertions(+)

diff --git a/drivers/gpu/drm/sun4i/sun4i_backend.c b/drivers/gpu/drm/sun4i/sun4i_backend.c
index 4fefd8add714..d18d7e88d511 100644
--- a/drivers/gpu/drm/sun4i/sun4i_backend.c
+++ b/drivers/gpu/drm/sun4i/sun4i_backend.c
@@ -216,6 +216,13 @@ int sun4i_backend_update_layer_buffer(struct sun4i_backend *backend,
 	paddr = drm_fb_cma_get_gem_addr(fb, state, 0);
 	DRM_DEBUG_DRIVER("Setting buffer address to %pad\n", &paddr);
 
+	/*
+	 * backend DMA accesses DRAM directly, bypassing the system
+	 * bus. As such, the address range is different and the buffer
+	 * address needs to be corrected.
+	 */
+	paddr -= PHYS_OFFSET;
+
 	/* Write the 32 lower bits of the address (in bits) */
 	lo_paddr = paddr << 3;
 	DRM_DEBUG_DRIVER("Setting address lower bits to 0x%x\n", lo_paddr);
-- 
2.14.2

_______________________________________________
dri-devel mailing list
dri-devel@xxxxxxxxxxxxxxxxxxxxx
https://lists.freedesktop.org/mailman/listinfo/dri-devel




[Index of Archives]     [Linux DRI Users]     [Linux Intel Graphics]     [Linux USB Devel]     [Video for Linux]     [Linux Audio Users]     [Yosemite News]     [Linux Kernel]     [Linux SCSI]     [XFree86]     [Linux USB Devel]     [Video for Linux]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [XFree86]
  Powered by Linux